2404 series stainless steel straight pipe fittings S30400 elbows

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.?Butt-weld and forged fittings are available.Excellent corrosion resistance in many acidic and alkaline environments Especially suitable for reducing conditions. Good ductility and thermal conductivity Ideal for seawater applications.

The Stainless Steel 904L Pipe Fittings were designed with the intention of being used between moderate to high corrosion resistance across a wide range of processing industries.

Used in chemical and petroleum processing, in power plants for superheater and reheater tubing, in industrial furnaces, and for heat treating equipment.

The A420 Grade WPL6 fitting is used in pipelines in the paper and pulp industries, condensers, sea water, marine engineering, waste water management and pollution control systems.

Hastelloy C22, also known as alloy C22, is a versatile austenitic nickel-chromium-molybdenum-tungsten alloy with enhanced resistance to pitting, crevice corrosion and stress corrosion cracking.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Hastelloy C-276 alloy can be forged, hot-upset, and impact extruded. Although the alloy tends to work-harden, it can be successfully deep-drawn, spun, press formed or punched.

Pipe fittings of ASTM A420 WPL6 are widely utilized in pressure piping and pressure vessel service at low-temperatures.ASTM A420 is the standard specification for pipe fittings of carbon steel and alloy steel used for low temperature services.

These fittings don‘t deform or dissociate easily at high pressures and elevated temperatures. The Alloy 600 Fittings possess superior strength and excellent mechanical properties. They possess a minimum tensile strength of 655Mpa and a minimum yield strength of 310 Mpa.

In this standard it covers the specification of elbows, tees, reducers, caps and cross, it usually adopt butt welding ends.

Inconel 625 pipe fittings are available in ATSM B366 and ASME SB366 specifications. The tensile strength of Din 2.4856 Welded Buttweld Fittings is 1,35,000 psi 930 MPsand yield strength is 75,000 psi 517 MPa. UNS N06625 Cross are manufactured using push, cast, press, and forge processes. These fittings are available in the price range of Rs. 12,700 to Rs 2 lakh. We are among the leading manufacturers of alloy 625 reducer fittings and provide you the best quality product at an affordable price. Customer satisfaction is our ultimate goal. We assist in choosing the fittings as per the customers’ needs and specifications.

A butt weld pipe reducer enables there to be a change in pipe size to meet certain hydraulic flow requirements or sometimes it’s just a matter of connecting two different pipe sizes. An eccentric butt welding reducer is a pipe fitting that is used when a pipe on the upstream side of the fitting is larger than the downstream side of the fitting.

Alloy Steel ASTM A234 WP22 Buttweld Fittings are one of the most demanding products among various industries around the world.We are a manufacturer, trader, stockist, supplier and exporter of A234 WPL22 Pipe Fittings which abide by the specifications of ASTM A234, which include wrought Carbon steel as well as Alloy Steel fittings, of seamless and welded construction.

Stainless steel 316l pipe fittings are of a low carbon austenitic grade. The versatile pipe fittings are designed with a superior content of chromium, nickel, and small amounts of molybdenum.

A234 WPB Elbow is produced and supplied in the butt welded form. SA234 WPB Elbow usually comes in either of three angles; 22.5, 45 or 90 degrees.

This feature is also particularly useful in procedures that use Nickel 201 fittings in the manufacture and processing of sodium hydroxide, which in turn is considered a special kind of caustic. Particularly unaffected by sodium hydroxide even at temperatures above 300 ¡ãC.

The fittings are also hard with a Brinell hardness sore of 210HB maximum. These can also operate under very high temperatures up to 870 degrees Celsius.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

316L steel is more susceptible to gaining some degree of magnetism.

Incoloy 800H is a high carbon grade of these 800 alloys. These alloys exhibit excellent resistance to post-weld carburization and graining. They remain ductile for extended periods of time at temperatures below 700 degrees Celsius.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

The austenitic structure of 316 stainless steel pipe bend gives excellent toughness, even at cryogenic temperatures.

The alloy has been used in a variety of applications. It has excellent resistance to rapidly flowing brackish water or seawater. It is particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated.

S31803 is resistant to stress chloride corrosion cracking, and duplex stainless steel exhibits the best corrosion performance in high temperature and sulfide environments.

Meanwhile, these Duplex Steel S32205 Cross Pipe Fittings are also available to our customers in different sizes and shapes. Duplex steel S31803 bent butt welded pipe fittings generally perform well in environments that cause premature failure of austenitic grades. Although duplex steel S32205 short end butt welded pipe fittings have good high temperature oxidation resistance, this grade – like other duplex stainless steels – can experience embrittlement if held at temperatures above 300 degrees Celsius for even short periods of time. If embrittled, duplex S31803 end caps can only be corrected by full solution annealing. Duplex S32205 Disc Lid Fittings are almost never used above 300 degrees Celsius.

There are different types of fittings such as bends, tees, crosses, reducers, caps and the WPHY 52 Elbow.In sour service wells, when hydrogen sulphide gas reacts with water, the hydrogen molecule gets deposited either on the pipes or fittings.

When titanium is mixed with other metals, the alloys can reach a tensile strength of more than 1,400 MPa, which makes 200,000 psi.

Inconel 625 elbow is made of high-performance nickel-chromium-molybdenum alloy known for its high level of strength, temperature resistance, and corrosion resistance.

ASTM A403 WP304H has a high carbon content in chemical compositions.ASTM A403 WP304H normally is used for the pressure piping systems of moderate and high temperature services. WP304H is a kind of heat and corrosion resistant steel.It has a good pipe bending,welding performance,heat and corrosion resistance,high rupture strength and stability,also the cold deformation ability is very good.It could be used up to 650¡ãC,oxidation temperature up to 850¡ãC.