1-8 in 4 inch 8 inch female ss 316 cap

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Incoloy 800H is a solution heat treated, carbon controlled version of its parent Alloy 800.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

Stainless steel 310 fittings are more corrosion resistant than grade 304 and 316 fittings. They are also resistant to oxidation and high temperatures. These are suitable for pressure piping applications. The material of stainless steel 310 fittings contains 24% chromium and 19% nickel, as well as carbon, manganese, silicon, phosphorus, sulfur, molybdenum and nitrogen. This special composition also provides additional corrosion resistance and strength to the material.

About high strength and excellent impact toughness, stress corrosion cracking resistance and high strength are exhibited by its Ferritic nature where as ease of fabrication and corrosion resistances are exhibited by its Austenitic nature. UNS S31803 Pipe Fittings has high applicability where demand for good corrosion resistance and good strength is required. In oxidizing, acidic and caustic environments, it exhibits good resistance towards pitting and crevice corrosion.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Although 316L contains less carbon, 316 and 316L stainless steels cost approximately the same.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

A tee is a type of pipe fitting that is used to divide the main flow into two streams or to combine flow from two streams. Because the form of a pipe tee resembles the alphabet “T”. The primary pipe of a Tee is frequently referred to as the main pipe or run pipe, and others as its branches.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Duplex steel S32205 tee butt welded pipe fittings are often used in chemical process industries: such as sulfuric acid production, nitric acid process, phosphoric acid process, ethylene oxide, polypropylene production, PVC, equipment for handling organic and fatty acids, chemical storage and tankers, thermal switch, etc.

Duplex Steel S31803 Front Ferrule Fittings are used in commercial and aerospace applications and can be freely formed and have best-in-class weldability. Given that the dual-phase steel S32205 rear ferrule joint is only about one-third the weight of comparable steel parts, it is the clear choice when weight is an aspect.

Inconel Tube Fittings can be easily elongated by 40% and still possess excellent workability. These fittings have a melting point of about 1413 degrees C and have a long service life. The Inconel 600 Buttweld Fittings can be produced by hot or cold rolling processes.

The strength of Inconel 625 lies not only in its nickel-chromium base but also the hardening mechanism of niobium and molybdenum.

The process to produce cast stainless steel pipe fittings is investment casting in lost wax method. In stainless steel investment casting, a specific and general wax pattern of the preferred pipe fitting is produced and mounted onto a wax tree. The wax tree is interchangeably plunged into a ceramic substance and topped with a stucco material. After this, it is left to dry out, and the process is repeated until a thick shell is achieved.

Inconel 600/601/625/718 Butt Weld Heads are a product with many reliable features to prevent cracking and rusting. If the product is free of cracks, the service life of the product will automatically increase.

A pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction
or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Duplex stainless steel pipes and fittings are generally less expensive because of the lower proportions of alloying elements used in the manufacture of duplex stainless steels. Compared to austenitic stainless steels, duplex stainless steels have higher yield strengths, so users can buy duplex pipes and duplex pipe fittings in relatively lower thicknesses.

In these standard Grade WPB is the most common material used for medium and high temperature pipelines. W means weldable, P means pressure, B is grade b, refer to the minimum yield strength.

The greater content of alloying elements like chromium, molybdenum, and nitrogen in SD UNS S32750 tee helps material in withholding crevice corrosion and pitting. SD UNS S32750 cross is combining greater mechanical strength and with good ductility with resistance to corrosion in a different atmosphere.

Duplex UNS S32205 Pipe Elbows are used where the direction of the pipe must be changed and there is less stress on the pipe wall. Elbow is one of the most commonly used accessories. Most fittings have nominal bores ranging from 1/8″ to 42″.

These Buttweld 45 Degree Weld Elbows with Tangents are manufactured to very high tolerances via hydroforming. Hydroforming results in a more uniform fitting that is easier to weld and polish. This manufacturing method allows us to supply a superior quality fitting regardless of the application. Suitable for use in applications ranging from food and beverage, dairy, and pharmaceutical to marine and automotive.

Duplex steels derive identical austenitic and ferritic fractions of a mixed microstructure. Ferritic alloys offer strength against stress cracking, while austenitic alloys offer ease of manufacture and rust resistance. These tubular fittings work under acid reducing and oxidizing conditions and in building materials in gas desulfurization plants. The higher the nitrogen content, the better the corrosion resistance.

Inconel alloy butt welded joints are used in all steel industries due to their high quality raw materials and design. Not sure, but mostly the steel and metals industries buy products so that butt welding can take the pressure. It is mainly used in the petrochemical industry because butt welding performs well in terms of processing temperatures, but also the automotive and refining industries are major users.

Stainless steel grade 316Ti is a titanium stabilized version of alloy 316. This austenitic chromium-nickel stainless steel grade contains substantial addition of molybdenum which is why the Stainless Steel 316Ti Pipe Fittings exhibits several important characteristics. For instance, grade 316Ti show an increase in the corrosion resistance properties along with improved resistance to pitting chloride ion solutions as well as increased tensile strength at elevated temperatures.

Stainless steel pipe is a kind of hollow long round steel or square rectangular material, which is widely used in industrial transmission pipelines and mechanical structural parts. In addition, with the same bending and torsional strength, stainless steel pipes are lighter in weight, so stainless steel pipes are also widely used in the manufacture of mechanical parts and engineering structures.

The stainless steel 45 degree butt weld elbow is a pipe fitting that is attached to two pieces of pipe to allow a change in direction. Stainless steel butt weld elbows can come in various degrees of angles and schedules. The most common angles available are 45 degree elbows and 90 degree elbows. 90 degree elbows are available in long radius and short radius.

Usually the ASTM A234 WP9 elbows,tees,reducers are made from steel pipes,the caps are made from plates.But the large sizes pipe fittings are commonly manufactured in pieces and welded together.In hot or concentrated solutions, rates of these Alloy Steel WP9 Cross Butt Weld Fittings are typically too high for sensible service life.

Stainless steel is an alloy of iron that is resistant to rusting. It contains at least 11% chromium and may contain elements such as carbon, other nonmetals and metals to obtain other desired properties. Stainless steel’s resistance to corrosion results from the chromium, which forms a passive film that can protect the material and self-heal in the presence of oxygen.
A stainless steel pipe system is the product of choice for carrying corrosive or sanitary fluids, slurries and gases, particularly where high pressures, high temperatures or corrosive environments are involved. As a result of the aesthetic properties of stainless steel, pipe is often use in architectural applications.

Duplex Steel S31803 Elbow Butt Weld Fittings are stainless steel, a type of stainless steel designed to improve resistance to pitting, high strength, stress corrosion, crevice corrosion and cracking. Duplex steel S31803 tee butt welded pipe fittings are often used in chemical process industries: such as sulfuric acid production, nitric acid process, phosphoric acid process, ethylene oxide, polypropylene production, PVC, equipment for handling organic and fatty acids, chemical storage and tankers, thermal switch, etc.