1-8 inch npt male and female pipe fittings 2205 elbows

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Some of the typical applications of duplex steel grade 2205 are oil and gas exploration, processing equipment, transport, storage and chemical process, high chloride and marine environments, paper machines, liquor tanks, pulp, and paper digesters.

ASTM A860 MSS SP 75 WPHY 52 Fittings are generally used at High Pressure requirements.Our wide range of Grade WPHY 52 Pipe Fittings includes: WPHY Gr 52 Bend, Elbow WPHY 52 in 45/90 degree, WPHY Grade 52 Tees, Carbon Steel WPHY 52 U Bend, MSS SP75 WPHY Gr 52 Stubends & ASTM A860 WPHY Grade 52 Pipe Nipple.

These fittings contain small amounts of additional copper, titanium and molybdenum, which improve their chemical and mechanical properties. Our UNS N08825 Incoloy 825 elbows have been designed to provide increased resistance to crevice and pitting corrosion and to operate smoothly at moderately elevated temperatures.

SS 304 Concentric Reducer also exhibits excellent ductility, spinning, forming and drawing properties.

There is a complete solid solution between nickel and copper. The wide solubility range between iron, chromium and nickel enables many alloy combinations. There are many different stainless steel grades in this category with their unique properties and performance in different conditions and environments.

ASTM A234 WP22 Pipe Fittings are made up of the specification that has carbon, manganese, silicon, sulfur, phosphorous, chromium and molybdenum in its composition. The molybdenum content is 0.9-1.1% of the composition which makes this grade specific. This grade has a tensile strength of 380MPa minimum and a yield strength of 585MPa minimum.

AS1210 Prequalified Incoloy 800 can be used at 800¡ãC. ASME codes allow Incoloy 800 to 815¡ãC, and Incoloy 800H and 800HT to 982¡ãC.

This modification was to control carbon (.05-.10%) and grain size to optimize stress rupture properties. Incoloy 800HT has further modifications to the combined titanium and aluminum levels (.85-1.20%) to ensure optimum high temperature properties.

Type 304 stainless steel is a T 300 Series Stainless Steel austenitic. It has a minimum of 18% chromium and 8% nickel, combined with a maximum of 0.08% carbon. It is defined as a Chromium-Nickel austenitic alloy.304 stainless steel is used for a variety of household and industrial applications such as food handling and processing equipment, screws,[3] machinery parts, utensils, and exhaust manifolds. 304 stainless steel is also used in the architectural field for exterior accents such as water and fire features. It is also a common coil material for vaporizers.

The 317L (00Cr19Ni13Mo3, UNS S31726) alloy is a molybdenum-based austenitic stainless steel. It is more resistant to chemical corrosion than conventional chromium-nickel austenitic stainless steels such as 304 alloy. In addition, compared with conventional stainless steel, 317L alloy has higher ductility, stress corrosion resistance, compressive strength and high temperature resistance. It is a low carbon grade or L grade, which is resistant to sensitization during welding and heat treatment.
Compared with 316L, 317L steel has good seawater resistance and SCC resistance, and is used in chemical ships, chemical products Reactor and other chemical equipment requiring high corrosion resistance.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Alloy 20 (Alloy 20) is an iron-based austenitic alloy developed to resist sulfuric acid corrosion. It has excellent resistance to sulfuric acid corrosion; it has strong resistance to phosphoric acid, nitric acid and chloride environments, chloride stress corrosion, pitting corrosion and crack corrosion. Therefore, alloy 20 has the name of anti-corrosion alloy; it has a wide range of applications: such as: chemical, food, medicine, power production and plastics industries will use it. For resistance to pitting corrosion and chloride corrosion, stress corrosion cracking problems, etc., alloy 20 is often used.

About high strength and excellent impact toughness, stress corrosion cracking resistance and high strength are exhibited by its Ferritic nature where as ease of fabrication and corrosion resistances are exhibited by its Austenitic nature. UNS S31803 Pipe Fittings has high applicability where demand for good corrosion resistance and good strength is required. In oxidizing, acidic and caustic environments, it exhibits good resistance towards pitting and crevice corrosion.

The SS 304 Elbow is one of the key components in the pressure piping system. It basically helps to change the direction of flow in the pipe run. These ASTM A403 Gr WP304 Buttweld Fittings help to connect two pipes with the same or different nominal diameters so as to change the fluid direction by 45 or 90 degrees.

Reducing tee, generally a professional term, tee for pipe fittings, pipe connectors, used in the main pipe to branch pipe.Reducing tee is a kind of tee, the tee has two kinds: general equal diameter tee and reducing tee.Named because the three ends can be connected to the pipe.

Cast stainless steel pipe fittings such as 304 and 316L can be used in all types of water, including drinking water in public supply. They have an excellent resistance to the full range of potable waters, including various chloride levels. At the end of its useful life, cast stainless steel is fully recyclable and retains a higher residual scrap value than ordinary cast steel.

Hastelloy B2 pipe bend resists the formation of grain boundary carbide precipitates in the weld heat-affected zone, making it suitable for most chemical process applications in the as-welded condition.

UNS S31803 Forged Threaded 45 Degree Elbow Fittings are widely recognized for their advanced finish, dimensional accuracy and corrosion resistance. It provides customers with excellent overall performance and therefore has some great features such as high quality, non-corrosiveness, cost-effectiveness, etc.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

2205 is a standard duplex steel with 21% chromium. The material is strong, twice as strong as austenitic steel types.

Hastelloy B2 pipe bend has excellent resistance to all temperatures and concentrations of hydrochloric acid.

The alloy is slightly magnetic at room temperature. Monel 400 is widely used in the chemical, oil and marine industries.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Pipe Tee is a type of pipe fitting which is T-shaped having two outlets, at 90¡ã to the connection to the main line. It is a short piece of pipe with a lateral outlet. Pipe Tee is used to connect pipelines with a pipe at a right angle with the line. Pipe Tees are widely used as pipe fittings.

ASTM A234 is standard of the pipe fitting material. However, this is indicating the properties of the material of various kinds of alloy steel and carbon steel. WPB is a steel grade in which W stands for weldable, B is grading B and P stands for pressure. Thus it is referring minimum yield strength.

ASTM A403 WP316 is the standard molybdenum-bearing grade, second in importance to 304 amongst the austenitic stainless steels. The molybdenum gives 316 better overall corrosion resistant properties than Grade 304, particularly higher resistance to pitting and crevice corrosion in chloride environments.

HT PIPE offers a full range of pipe fittings such as carbon steel reducers, carbon steel elbows, carbon steel tees, carbon steel crosses, carbon steel stub ends and carbon steel elbows. Our carbon steel or mild steel forged flange products include threaded flanges, butt weld flanges, slip flanges, socket weld flanges, blind flanges, lap flanges, plate flanges. We specialize in manufacturing flanges of special sizes and custom shapes for our customers.

SD reducers are designed for featuring resistance to pitting, corrosion fatigue, erosion-corrosion, SCC, crevice corrosion and also high strength and good welding ability. SD cross combines ductility, high mechanical strength and corrosion resistance at ranges of the atmosphere.

Type 316L stainless steel in a molybdenum bearing austenitic.