150 class ss304 316 stainless steel pipe fitting bw seamless elbows

Monel 400 is widely used in Brine heaters, sea water scrubbers in tanker inert gas systems.

Usage of Duplex 2507 should be limited to applications below 600¡ã F (316¡ã C). Extended elevated temperature exposure can reduce both the toughness and corrosion resistance of alloy 2507.

Grade WPB fittings made from the steel pipes or plates maximum C is 0.35%.

The austenitic structure of 316 stainless steel pipe bend gives excellent toughness, even at cryogenic temperatures.

Stainless Steel 304 Fitting Elbow is an austenitic chromium alloy with a steel composition of 18% chromium and 8% nickel. Stainless steel 304 pipe fittings have high ductility, excellent forming, spinning and drawing properties.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Hastelloy B2 is a nickel-molybdenum alloy with significant resistance to reducing environments, such as hydrogen chloride gas and sulfuric, acetic and phosphoric acids.

This is a nickel-copper, solid-solution alloy that is hardenable only by cold working. It has high strength and toughness over a wide temperature range and is resistant to many corrosive environments.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

Our reducers have high strength and corrosion resistance and are suitable for various industries.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

One of the greatest benefits of Inconel 600 fittings is their ability to maintain their performance even at high temperatures. It has a minimum yield strength of 310 MPa and a minimum tensile strength of 655 MPa. It has an elongation of 40%, which is pretty good. Inconel 600 material has a melting point of 1413 degrees Celsius, which makes it ideal for high temperature applications and has a long service life. It can be easily bent and welded, and the size can be customized according to specific requirements.

Incoloy 800 pipe fittings, resistant to seawater and salt water even in reducing environments.

Pipe bending methods will vary based upon the metals used.

Alloy 32750 is a super duplex stainless steel supplied in hot worked and solution annealed conditions. As a super duplex stainless steel, it combines the desirable aspects of austenitic and ferritic steels. Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature over 50¡ãC.

Nickel alloy 800 unequal tee fittings are considered suitable for metallurgical industry, shipping industry, pulp and paper industry, food industry, oil and gas industry, energy industry, chemical industry, seawater desalination industry, etc. With the help of using us, we provide a range of pipe fittings which are also factory made with an excellent well-established infrastructure facilitated by quality and current machines.

Made of stainless steel 304/304L, this fitting is low in carbon to minimize harmful carbide precipitation during welding and ensure corrosion resistance. Elbow meets 304 steel strength standard and 304L extra low carbon standard for quality assurance. Fittings are components used in many different industries to connect, terminate, control flow and change the direction of pipes.

Grade 316 pipe bend also has given excellent service in potable water. Pitting and crevice corrosion may occur in waters with higher chloride content, and 2000 ppm is accepted as the upper limit. The higher molybdenum content of 316 make it significantly more corrosion resistant than grade 304.

Inconel Tube Fittings can be easily elongated by 40% and still possess excellent workability. These fittings have a melting point of about 1413 degrees C and have a long service life. The Inconel 600 Buttweld Fittings can be produced by hot or cold rolling processes.

Steel tee is a T-shaped pipe fittings that has three branches, normally has two forms with Equal Tee and Reducing Tee (Tee reducer), both are used to divide (combine) the pipelines to adjust the flow rate and change the direction.

The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content.

Incoloy 800 or also referred to as UNS N08800, nickel 800 has excellent resistance properties to chemicals as well. Renowned for its high tensile strength at elevated temperatures, Alloy 800 also resists oxidation, carburization as well as other types of high-temperature corrosion.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

The fittings made up of carbon steel are applied through various industrial, commercial and domestic applications.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Type 304 is the most popular stainless steel and is a natural choice for its corrosion resistance. It resists rusting in many different environments, but is primarily attacked by chlorides.

HT PIPE offers a range of precision finished duplex fittings & flanges to ensure a good flow in seamless. Our flanges are corrosion resistant & designed to operate in high pressure environments. Here at HT PIPE we supply a broad range of piping products and materials which are used in many different industries.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.?Butt-weld and forged fittings are available.Excellent corrosion resistance in many acidic and alkaline environments Especially suitable for reducing conditions. Good ductility and thermal conductivity Ideal for seawater applications.

The superposition of residual stress caused by cold working and aging thermal stress, as well as the preferential embrittlement of the surface layer at the initial stage of aging, are the main reasons for aging cracking of Monel K500 alloy.