150# duplex 304 316 pipe fittings with elbows

A pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction
or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Nickel Alloy 600 works well with most alkaline solutions and sulfur compounds and also provides lower rate of attack from chlorine or hydrogen chloride.

Hastelloy Alloy C276 Pipe Fittings, which are used as matching composition filler material for welding alloy, wrought and cast products. For optimum corrosion performance in Hastelloy C276 Butt Weld Fittings, therefore, the re-annealing of cold worked parts is important. To obtain a reducing media in Hastelloy C276 Elbow Pipe Fittings, add 2 % (by volume) of either ethyl or propyl alcohol to water. During machining, Hastelloy C276 Tee Pipe Fittings work harden rapidly, generate high heat during cutting, weld to the cutting tool surface and offer high resistance to metal removal because of their high shear strengths. Hastelloy C276 Cross Pipe Fittings is used for Flue gas desulfurization system, Aramide plastics production, and Pickling baths. Hastelloy C276 Reducer Pipe Fittings is commonly used in Flue Gas Desulfurization (FGD) applications for scrubbers, dampers and ducts.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

Due to the lower carbon content in 317L fittings, the alloy can be welded without intergranular corrosion. Generally, intergranular corrosion is the result of chromium carbide precipitation on the surface of metals with a higher carbon content and prolonged exposure to high temperatures. Because the alloy used for 317L joints can withstand high temperatures without being corroded by intergranular corrosion, these joints can be used in the as-welded condition.

Each method has unique benefits and will determine the degree of bending possible and the final shape of the pipe.

Our WNR 1.4462 Duplex Steel S31803 Pipe Fittings withstand sulphur-induced stress corrosion cracking, accommodate high steam pressures and provide extended service life, economical and reliable.

However, titanium can lose its strength at temperatures greater than 430?C because it is not as hard as high grades of steel.

We are a manufacturer, trader, stocker, supplier and exporter of alloy 20 pipe fittings made from niobium stabilized austenitic pipe fittings that minimize carbon induced carbide precipitation during welding.

Nickel Alloy 600, also sold under the brand name Inconel 600. It is a unique nickel-chromium alloy that is known for its oxidation resistance at higher temperatures.

Steel tee is a T-shaped pipe fittings that has three branches, normally has two forms with Equal Tee and Reducing Tee (Tee reducer), both are used to divide (combine) the pipelines to adjust the flow rate and change the direction.

All stainless steel fabrication can only be done using tools designed for stainless steel materials. Tools and work surfaces must be thoroughly cleaned before use. These precautions are necessary to avoid cross-contamination of stainless steel with easily corroded metals that may discolor the surface of processed products.

317L stainless steel 180 degree elbow has very high corrosion resistance, but it is getting more and more expensive. The products we offer are known throughout the world for their reliability and quality.

In the piping system, the stainless steel short radius elbow 1.5d is a pipe fitting that changes the direction of the pipe. There are three most commonly used ASME short radius elbows, depending on the angle. In addition to the conventional 45¡ã SR Bw elbow, 90¡ã SR Bw elbow, and 180¡ã SR Bw elbow, other non-normal angle 12-inch short radius elbows such as 60¡ã are also included according to engineering needs.

Stainless Steel 347 Fitting is an austenitic stainless steel with a nominal composition of 17% Chromium and 7% Nickel with good strength and ductility when cold worked.

Sanitary pipe fittings AISI304, AISI304L, AISI316, AISI316L, its standard is DIN/SMS/3A/ISO/IDF, pipeline flow control: DN10-DN200&1 /4″”-8″, it is used in stainless steel pipe system, its working principle It can be welded on the pipeline to adjust the flow in the pipeline. Its medium includes beer, dairy products, beverages and pharmaceuticals.

Fully austenitic welds are more prone to cracking during welding. For this reason, Type 316 and Type 316L “matching” filler metals are formulated to cure with a small amount of ferrite in the microstructure to minimize cracking susceptibility.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

Stainless steel 304 fittings contain 18% – 20% chromium and 8% – 10.5% nickel. It is an austenitic stainless steel with lower electrical and thermal conductivity than carbon steel. It is a component that helps to change the direction of flow, such as tees and elbows.

HASTELLOY X pipe bend is a wrought nickel base alloy with excellent high temperature strength and oxidation resistance. All of the product forms are excellent in terms of forming and welding.

When choosing pipe fittings, material is always a big part of the choice. Stainless steel offers excellent protection against corrosion and rust, something which could prove hugely troublesome within water and gas pipes. Brass and copper pipes wouldn’t have the same resistance to these kinds of issues.

Hex bolts are used to fasten two or more parts together to form an assembly either because it cannot be manufactured as a single part or to allow for maintenance and repair disassembly. By definition “A Bolt is a headed and externally threaded mechanical device designed for insertion through holes in assembled parts to mate with a nut and is normally intended to be tightened or released by turning that nut.” When used with a preformed internally threaded (tapped) hole, the hex bolt’s head is turned to tighten, which technically makes it a screw (see our Tech Data section for a discussion regarding the differences between bolts and screws). Hex bolts are also known as: hex head bolts, cap screws, hex cap screws, hex head cap screws, machine bolts, hex machine bolts, hex head machine bolts and, if fully threaded, tap bolts, hex tap bolts and hex head tap bolts. A hex bolt is often differentiated from a hex cap screw by its underhead bearing surface: if it has a circular boss, called a washer face, it’s a hex cap screw¡ªif it doesn’t then it’s a hex bolt.

The UNS S32760 Pipe Fittings have high tensile strength, durability, and excellent corrosion resistive property. The specifications of SA 815 WPS S32760 Elbow has criteria like size, standard, type and many more.

The alloy also has excellent mechanical properties and presents the desirable combination of high strength and good workability.

Sanitary elbows are a crucial link in the chain of fluid systems everywhere. While these types of equipment are highly specialized in nature, their presence in industrial, commercial, and even residential spaces is more ubiquitous than you might think.

The stainless steel 45 degree butt weld elbow is a pipe fitting that is attached to two pieces of pipe to allow a change in direction. Stainless steel butt weld elbows can come in various degrees of angles and schedules. The most common angles available are 45 degree elbows and 90 degree elbows. 90 degree elbows are available in long radius and short radius.

The Stainless Steel Fittings Manufacturers produce these fittings with the addition of manganese, phosphorus, carbon, silicon, and sulfur apart from the 2 main elements.

Our ASTM A815 Duplex Steel UNS S32205 Caps are available in a variety of cap shapes, diameters and thread types and are resistant to many industrial acids and seawater.

To qualify as 316L stainless steel, the amount of carbon cannot exceed 0.03%. This decreases the risk of carbon precipitation, making it a better option for welding to ensure maximum corrosion resistance.