150lb bsp pipe fittings ASTM A815 UNS S32750 EQUAL TEE

MONEL K500 retains the excellent corrosion resistant characteristics of 400 and has enhanced strength and hardness after precipitation hardening when compared with 400.

Duplex UNS S31803 Tee Fittings have high general corrosion resistance. Duplex UNS S31803 Cross Fittings provide good weldability in thick plates. Duplex UNS S31803 Reducer Fitting is a duplex stainless steel with a 50/50 austenitic, ferritic microstructure.

Alloy 20 pipe fitting is a chromium-iron-nickel-based, austenitic alloy that comes with excellent corrosion resistance in chemical environments. It contains sulfuric acid and many aggressive media well. The alloy is stabilized with niobium that helps it to resist intergranular corrosion.

321 stainless steel, also known as UNS S32100 and Grade 321, is primarily comprised of 17% to 19% chromium, 12% nickel, .25% to 1% silicon, 2% maximum manganese, traces of phosphorus and sulfur, 5 x (c + n) .70% titanium, with the balance being iron. With regards to corrosion resistance, 321 Stainless Steel is equivalent to Grade 304 in the annealed condition and is superior if the application involves service in the 797¡ã to 1652¡ã F range. 321 Stainless Steel combines high strength, resistance to scaling and phase stability with resistance to subsequent aqueous corrosion.
UNS S32100 Reducing Tee is preferred due to its ability to work in high pressure and temperature even at a higher temperature.
Stainless Steel 321 / 321H Pipe Fittings are used in filtration, refrigeration, oil, gas, petrochemical and in offshore oil drilling industries. The material has chromium, nickel, titanium and other elements along with carbon. The 321H has higher carbon than the other versions. There are different types of fittings such as the 321/321H Stainless Steel Buttweld Fittings which are most commonly used but there are also the seamless fittings. The Stainless Steel UNS S32100 Pipe Elbow is a fitting type that is used in high temperature applications to change direction of flow.

With Up To 3000 Ton Capacity Proficient Of Cold Forming 8″ Nb SS 304 Fitting And ASTM A403 WP304 Elbow Upto 12″ Nb And Wall Thicknesses Upto 0.75″ Thick As Per Ansi/ Asme B16.9.

Incoloy 825 fittings are known for their resistance to chloride stress-related corrosion cracking and pitting. We are a leading manufacturer and supplier of ASTM B366 Alloy 825 Elbow. The addition of titanium to the alloy is what stabilizes the alloy 825 tee against sensitization in the as-welded state. Thus, making these fittings resistant to intergranular attack even in temperature ranges that would normally make unstable conventional-use stainless steel grades sensitive.

Alloy 800H/800HT is frequently used in applications that involve long-term exposure to elevated temperatures where resistance to oxidation, carburization and other types of elevated temperature corrosion is required.

HT PIPE offers a range of precision finished duplex fittings & flanges to ensure a good flow in seamless. Our flanges are corrosion resistant & designed to operate in high pressure environments. Here at HT PIPE we supply a broad range of piping products and materials which are used in many different industries.

There are different types of fittings such as bends, tees, crosses, reducers, caps and the WPHY 52 Elbow.In sour service wells, when hydrogen sulphide gas reacts with water, the hydrogen molecule gets deposited either on the pipes or fittings.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

They can operate in a temperature range of 450¡ãC to 850¡ãC. They can also be customized to specific requirements and have passed various tests to confirm maintaining the performance of this SS 316L eccentric reducer.

Inconel 718 elbows are commonly used in gas turbine engine parts, wellhead completions and blowout preventers (BOPs).

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

There are 5 most common ASTM A234 WPB Elbow are in mainly in demand, the 45¡ã, 90¡ã and 180¡ã elbows, all three in the “long radius” version, and in addition the 90¡ã and 180¡ã elbows both in the “short radius” version.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Hastelloy C276 alloy, UNS N10276, 2.4819, is the most widely used and versatile corrosion resistant nickel alloy.

ASME B366 Incoloy 800 Elbow resists water corrosion at moderate temperatures.

If embrittled, duplex S31803 end caps can only be corrected by full solution annealing. Duplex S31803 Disc Lid Fittings are almost never used above 300 degrees Celsius. Duplex steel S31803 bent butt welded pipe fittings generally perform well in environments that cause premature failure of austenitic grades. Although duplex steel S31803 short end butt welded pipe fittings have good high temperature oxidation resistance, this grade – like other duplex stainless steels – can embrittle even for short periods of time if held at temperatures above 300 degrees Celsius. If embrittled, duplex S31803 end caps can only be corrected by full solution annealing.

Pipe bending allows systems to minimize pressure changes while still routing materials through complex piping systems.

Adapters and fittings for stainless steel, carbon steel and other materials for oil and gas, petrochemical, power, pulp and paper and other applications. As a supplier of stainless steel and carbon steel pipe fittings, we provide industrial pipe fittings to meet your project needs.

They can also be seamless in nature. The nominal diameter of the seamless fittings ranges from ? inches to 24 inches and the welded fittings range from ? inches to 120 inches in diameter.

Inconel 625 pipe fittings are available in ATSM B366 and ASME SB366 specifications. The tensile strength of Din 2.4856 Welded Buttweld Fittings is 1,35,000 psi 930 MPsand yield strength is 75,000 psi 517 MPa. UNS N06625 Cross are manufactured using push, cast, press, and forge processes. These fittings are available in the price range of Rs. 12,700 to Rs 2 lakh. We are among the leading manufacturers of alloy 625 reducer fittings and provide you the best quality product at an affordable price. Customer satisfaction is our ultimate goal. We assist in choosing the fittings as per the customers’ needs and specifications.

Monel k500 has good corrosion resistance and long-term organizational stability.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Monel 400 Tee is a nickel-copper alloy resistant to seawater and steam at high temperatures, as well as salts and corrosive solutions. Monel 400 Pipe Elbows operate over a wide temperature range and are available in a variety of styles for a variety of products.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Monel 400 is widely used in Brine heaters, sea water scrubbers in tanker inert gas systems.

They are corrosion proof and can last longer for their suppliers. They are made of top-grade metals that meet ANSI, DIN, BS, ASME and JIP specifications and are ideal for applications involving excessive stress and temperature. Incoloy UNS N08800 Tee Fittings are ideal for suppliers with excessive temperatures. Utilizing our extensive distribution network, we source and process a wide and varied range of pipe fittings that are synthesized using high-grade metals at our licensed premises. It was developed to business specifications and is ideal for use in numerous business applications. Fittings with precision drilled holes align effortlessly with pipes.

Grade 310S Stainless Steel Butt Weld Pipe Fitting contains low Carbon, with higher Nickel and Chromium content curbing Hydrogen sulphide attack, which used in various industries like heat exchangers, furnace parts, shipbuilding, heat treatment baskets, condensers, offshore etc.
The fittings are shaped up and then heated to a high temperature following a rapid cooling closer to the cooling in still air. This rapid cooling adds to the strength of the Stainless Steel 310 Pipe Fittings and makes them much stronger. The SS 310S Fitting is used in industries like the sea water processing, thermal energy generation plants and much domestic piping as well. 310S SS Weld Fittings is used in different pressure classes to cope up with the pressure containment requirement of the application as well.

S32205 is a duplex stainless steel with twice the strength of austenitic stainless steel. Duplex stainless steel composed of 21% chromium, 2.5% molybdenum and 4.5% nickel-nitrogen alloy. It has high strength, good impact toughness and good overall and local stress corrosion resistance. The yield strength of duplex stainless steels is twice that of austenitic stainless steels, a feature that allows designers to reduce weight when designing products, making this alloy more affordable than 316, 317L. This alloy is particularly suitable for use in the -50¡ãF/+600¡ãF temperature range. For applications outside this temperature range, this alloy can also be considered, but there are some limitations, especially when applied to welded structures. Duplex stainless steel has twice the compressive strength compared to austenitic stainless steel, and designers can reduce its weight compared to 316L and 317L. Alloy 2205 is particularly suitable for use in the -50¡ãF/+600¡ãF temperature range, and can also be used at lower temperatures under severe restrictions (especially for welded structures).