201 202 304 904l 304l stainless steel plate

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

ASME B36.19M is the standard specification for stainless steel pipes, which specifies the dimensions, tolerance, and manufacturing requirements for both welded and seamless pipes.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

304 Piping Spools are made of 304 Stainless Steel, a common and popular material in many industrial applications that require resistance to corrosion and oxidation. These S30400 Piping Spools are prefabricated using specialized machinery and processes, which ensure that they are highly accurate and reliable.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

Inconel 718 is a nickel-chromium-based alloy that is commonly used in high-temperature applications such as aerospace and gas turbines. One of the most important factors in the production of ASTM B670 Inconel 718 Sheet is the plate rolling process. There are two main types of Inconel 718 plates available on the market: hot rolled and cold rolled plates.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

ASTM A182 Alloy Steel F22 Fittings are available in a variety of shapes, sizes and dimensions according to the needs or requirements of the application or to customer supplied specifications.

These ASTM A182 Grade F5 Flanges gives extraordinary erosion resistance in, for instance, caustic and acidic applications which includes sulphuric and higher chloride environments. A182 Gr F5 Threaded Flanges are mostly used in utility services such as air and water. It is similar to the Slip-On flange, but the bore is threaded. Its greatest advantage is that it can be assembled without welding, explaining its use in low pressure services at ordinary atmospheric temperatures, and in highly explosive areas where welding create a hazard.

HT PIPE has an excellent production company for designing and developing superior Pipe Fittings SS 316/316L. During the testing and production phases, our expert team examines strictly SS 316/316L buttweld pipe fittings.

316 stainless steel is more resistant to corrosion than 304 stainless steel, especially chlorides. This makes it a common choice for applications where marine equipment and other materials are exposed to extremely high concentrations of chlorides or other oxidizing agents. However, 304 stainless steel still has excellent corrosion resistance, so this is usually only a factor in marine environments and other high corrosion locations.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.66

The reason ASTM B637 UNS N07718 bolts are ideally chosen for the manufacture of turbine engines. Since a turbine engine operates on basic thermodynamic principles, the efficiency of a turbine engine increases as the turbine inlet temperature increases.

Annealing between 1050 and 1080¡ãC can be done after forging, followed by rapid quenching, especially to restore corrosion resistance, but there is no heat treatment to harden 316L.

INCONEL? alloy 718 (UNS N07718/W.Nr. 2.4668) is a high-strength, corrosion-resistant nickel chromium material used at -423¡ã to 1300¡ãF. Inconel alloys are resistant to oxidation and have the ability to maintain its structural integrity in high temperature atmospheres.

253MA steel pipe flanges are typically designed for low pressure, non-circulating industrial applications. These 253MA flanges are typically used in low pressure conditions.

The fertilizer and chemical processing industry use 310 310S Stainless Steel Flanges for mild cyclic operations. Furnaces, power generation and thermal processing industries function at extremely high temperatures, thus requiring flanges that are tough at such temperatures.

Bolts are chrome molybdenum heat treated steel according to ASTM A193 B7m specification for bolts. The primary alloy components of ASTM A193 Grade B7 bolts are chromium and molybdenum. These ASTM A193 B7 Metric Bolts are manufactured by heat quenching and tempering. Heat treating A193 B7 bolt material helps to develop desired mechanical properties such as increased tensile strength of ASTM A193 B7 hex bolts after heat treatment.

A flange is a ring of steel (forged, cut from plate, or rolled) designed to connect sections of pipe, or to join pipe to a pressure vessel, valve, pump or other integral flanged assembly. Flanges are joined to each other by bolts, and to the piping system by welding or threading (or loose when stub ends are used). Stainless steel flange simplified as SS flange, it refers to the flanges that made of stainless steel. Common material standards and Grades are ASTM A182 Grade F304/L and F316/L, with pressure ratings from Class 150, 300, 600 etc and to 2500. It used in more industries than carbon steel as stainless steel has better resistant performances on corrosion environment and always provides with a good appearance.

Hastelloy C276 Sheets, Plates and Coils (also referred as WNR 2.4819) that are actually manufactured from High Quality of Standard Raw Materials and are designed as per with national and international standards.

We are one of the well-known Manufacturers, Supplier, and Exporter of 254 SMO Flex Pipe, Stainless Steel 254 SMO Pipes, 6MO Stainless Steel Pipe, ASTM A312 UNS S31254 Seamless Pipe, 254 SMO Stainless Steel Pipe, Stainless Steel 254 SMO Welded Pipes which are using high-quality raw material.

SS 304 alloy steel is used in the development of pipes. However, the alloy is composed of chromium and nickel, which provide pipes and tubes with various properties. In addition to this, SS 304L has a lower carbon content than 304 alloy steel. This is how it excels at being resistant to intergranular corrosion. Likewise, SS 304H is an alloy for high temperature applications, with high temperature strength and the ability to operate at high temperatures.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.59

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

La tuberia 254 Smo se usa ampliamente en el tratamiento de agua de mar, procesamiento quimico, procesamiento de alimentos y produccion de petroleo. Tubo Smo 254 tambien se utiliza en sistemas de blanqueo de plantas de celulosa, desulfuracion de gases de combustion, lavadores y columnas de destilacion de tall oil.

Alloy 718 is a nickel-chromium alloy that is easy to manufacture and has excellent welding characteristics, especially where resistance to post-weld cracking is required.

Monel 400 is also often used for the high tolerance tubing. It exhibits excellent weldability, and it is often found in marine applications such as seawater valves and pump shafts. These tubes are also used in chemical plant equipment, boiler feeders, and heat exchangers. For applications that require a high melting point and toughness under the harshest conditions.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

The lower carbon content of the stainless steel 304 thread bar reduces chromium carbide precipitation from welding and its susceptibility to intergranular corrosion. Stainless steel 304 studs are not particularly thermally or electrically conductive and are non-magnetic. The large number of Style 304 Stud Bolts we manufacture today can be used in products related to the food and beverage industry. These AISI 304 studs are ideal for milk processing, brewing and winemaking as well as yeast trays, pipes, fermentation vats and storage tanks.

Astm B564 Monel 400 Blind Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

As experts in the field of fasteners, we recognize that this alloy can be used in a variety of applications including heat exchangers, piping, pressure vessels, tanks, fans, pulp and paper equipment, oilfield equipment and press rolls. At HT PIPE you can find Duplex Premium Gaskets in high quality.

Monel400 Copper-nickel alloy (UNSN04400) is a soft Copper-nickel alloy that is resistant to various corrosive environments.

Hastelloy 276 bolts and fasteners are suitable for most chemical applications in the welded condition. However, it should be noted that in environments where C-276 alloy weld joints are subject to attack, C-22 weld filler material should be considered. Hastelloy C276 socket head cap screws also have excellent resistance to pitting corrosion, stress corrosion cracking and oxidizing atmospheres up to 1900¡ãF.

SAE 304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel. It is less electrically and thermally conductive than carbon steel. It is magnetic, but less magnetic than steel. It has a higher corrosion resistance than regular steel and is widely used because of the ease in which it is formed into various shapes.[1]

ASTM A234 Pipe Fittings include Tee, Concentric reducer, eccentric Reducer, 5D/6D bend, elbow, unions, plugs, cross tee, pipe cap and nipple, ect for use in pressure piping and in pressure vessel fabrication for service at moderate and elevated temperatures.

Flanges are an integral part of processing based industries. Most industries, including the oil and gas, water treatment and nuclear power generation make use of pipes, which permit the flow of media across different factory units

Stainless steel sanitary fittings are the main components of sanitary process systems. As one of the sanitary solution providers, HT PIPE manufactures and supplies a wide range of sanitary fittings including DIN/SMS/3A/IDF/RTJ/ISO/BS welded fittings, unions, tri-clamps, ferrules, pinch fittings and short tube etc. We have the ability to provide qualified sanitary fittings that meet your high purity conditions and FDA, GMP requirements.

ASTM A320 L7 Stud Bolts are designed for low temperature performance. These fasteners are commonly used in valves, flanges, fittings and pressure vessels. The ASTM specification recommends a minimum impact value of 20-ft-lbf -150F for ASTM A320 L7 studs.

Type 316 stainless steel tubing is similar to 304, but with the addition of molybdenum, which improves the alloys corrosion resistance. The austenitic structure allows excellent toughness, even down to extremely low temperatures. These grades have excellent weldability, with or without the addition of filler metal.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

The specification for ASTM A320 Grade L7m materials covers alloy steel and stainless steel bolting materials for low temperature applications. ASTM A320 L7 Studs can also be used in applications with ambient temperatures up to -150oF. ASTM A320 grade L7m bolts and ASTM A320 bolts have a minimum Charpy impact value of 15 foot-pounds at this temperature.