2205 S31803 duplex pipe ferritic nickel alloyed stainless steel pipe

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

Super Duplex UNS S32760 has high resistance to pitting, crevice corrosion and stress corrosion cracking. For optimum corrosion resistance, a pickled or machined surface finish is recommended.

Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Material: Duplex Steel ASTM A789 S31803,S32205,S32750, S32760
ASTM A790 S31803,S32205,S32750, S32760

Astm A790 Uns S31803 grade pipes and tubes can be cold-rolled to give them enhanced properties and good resistances in different systems.

Duplex steel UNS S31803 hex nuts are widely suitable for the effects of sulphurous gases, especially above 900 degrees Celsius, very low.

The Super Duplex 2507 Tube can be used in high-pressure and temperature systems.

2205 flange has good general corrosion resistance, high resistance to chloride stress corrosion cracking, as well as pitting and crevice corrosion.

Light gauges of 2507 material can often be used to achieve the same design strength of thicker nickel alloys. Duplex 2507 plate is suitable for applications requiring excellent strength and corrosion resistance. It contains 25% chromium, 4% molybdenum and 7% nickel.

Duplex is often found in desalination and pressure vessel equipment located in port cities.

The duplex stainless steel grade alloy UNS S32750 Washer is a thin plate, which is typically produced in a disk -shaped, although sometimes square shaped with a hole i.e. sometimes present in the middle.

ASTM A1082 specification alloy S31803 fasteners have higher pitting and crevice corrosion than stainless steel alloy 316. Due to its higher corrosion resistance, alloy grade UNS S31803 is able to exhibit better fatigue strength than other commonly used austenitic stainless steel grades in environments containing corrosive media.

The yield strength of this alloy is about 570 MPa. In addition to strength, A240 S32750 Super Duplex Plate is an alloy that provides the best resistance to crevice and pitting corrosion.

A ferrous metal is one that contains iron. Therefore, stainless steels are ferrous metals as their main constituent is iron, even in the very highly alloyed grades, such as super duplex stainless steels, or super austenitic stainless steels.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The standard austenitic steels like 304 (1.4301) and ferritic steels like 430 are relatively easy to make and to fabricate. As their names imply, they consist mainly of one phase, austenite or ferrite. Although these types are fine for a wide range of applications, there are some important technical weaknesses in both types.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

UNS S32760 (F55, 1.4501) is a high alloy super duplex stainless steel mainly used in a variety of strongly corrosive environments. S32760 has strong strength and corrosion resistance and is mainly used in chemical processing, petrochemical and subsea equipment.

The microstructure and composition of the duplex 2205 alloy provides corrosion resistance superior to Type 316 or 317 in many environments, and its minimum yield strength is more than double that of conventional austenitic stainless steels.

This grade, with a tighter specification, is captioned as F60, equating to UNS S32205. Consequently, S32205 can be dual-certified as S31803 but not vice-versa.

S32760 also has high strength and extended service life. It is 10% lighter than grade 316 steel, ideal for sub-zero use, and more cost-effective than nickel alloys. Stainless steel grade F55 can be easily machined and welded.

S31803 has been supplemented by S32205 (F60) which has a higher minimum Ni Cr and Mo.

The advantage of the dual-phase structure is that it combines the advantages of ferritic alloys (resistance to stress corrosion cracking and high strength) with the advantages of austenitic alloys (ease of manufacture and corrosion resistance). The service temperature of 2205 duplex stainless steel should be limited to below 600¡ãF. Prolonged exposure to high temperatures can make 2205 stainless steel brittle.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.67

The round and hollow pipes are usual ones. In addition to the Duplex Stainless Hollow Pipes and the Duplex Steel Round Pipes there are square, rectangular and hexagonal pipes available in the market.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

It is a super duplex alloy, so heat resistance is also what Super Duplex 2507 rods are capable of. River or sea water often contains highly corrosive chemicals containing sulfur or chloride ions, and materials such as the 2507 Super Duplex Round Bar can withstand these chemicals.

2507 nuts are highly resistant to carbide-related intergranular corrosion due to their low carbon content (0.020% in weight).

Duplex stainless steel fasteners are made from alloys with high chromium content and low to moderate nickel content.

The material for UNS S32760 Stud Bolts is about 10% lighter when compared to grade 316 stainless steel. The Stud Bolt S32760 demonstrates high performance at cryogenic temperature settings as well. Which means that the ASTM A1082 UNS S32760 has good sub-zero notch ductility properties down to a temperature of minus 50¡ãC.

As well as greater tensile and yield strength whilst still providing good ductility and resistance to stress corrosion cracking.

These plates combine desirable properties of austenitic and ferritic grades.

Flat and lock washers can be cut or stamped from sheet to customer specifications. Since 2205 combines high strength, excellent corrosion and stress corrosion cracking resistance with very good pitting corrosion resistance and low thermal expansion, this may be the right alloy for your project nuts, bolts, spacers and studs.

Alloy 2507 has 25% chromium, 4% molybdenum, and 7% nickel. This high molybdenum, chromium and nitrogen content results in excellent resistance to chloride pitting and crevice corrosion attack and the duplex structure provides 2507 with exceptional resistance to chloride stress corrosion cracking.

“Duplex” describes a family of stainless steels that are neither fully austenitic (like 304 stainless steel) nor pure ferritic (like 430 stainless steel). The structure of the S31803 duplex stainless steel consists of a pool of austenite surrounded by a continuous ferrite phase.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.63