2205 S31803 duplex pipe high mechanical strength

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

2507 has a higher chromium and molybdenum content which gives the super duplex greater corrosion resistance than other standard duplex grades.

Duplex¡¯s premium mechanical and chemical properties are slightly offset by its difficulty in formability.

Although when the 2205 duplex stainless tubing material has been exposed to temperatures above 572¡ãF, even when the exposure is for a short period of time, the duplex 2205 seamless tube is subject to embrittlement.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

ASME SA 479 UNS S32205 Fastener is a corrosion resistant and high strength super alloy that can be used in low temperature ranges up to 1300 degrees Fahrenheit.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

Alloy 2205 gets the name Duplex because it is composed of two different types of grains. 40-50% of its grain structure is austenite and 50-60% of it is ferrite. It is closely related to, but much more popular than Alloy 255. In most environments, it surpasses 317L in crevice corrosion resistance. 2205 Duplex excels in chloride environments and resists hydrogen sulfide. 2205 Duplex has almost twice the strength of 316L. Due to the lower nickel and molybdenum content, it is less costly than Alloy C276. Among the places where 2205 Duplex is used include pressure vessels, heat exchangers and scrubbing systems.

Super Duplex Stainless Steel is known to have better stress corrosion, cracking resistance and mechanical properties than any other type of steel.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

Compared with ferrite, it has higher plasticity and toughness, no room temperature brittleness, significantly improved intergranular corrosion resistance and welding performance, and maintained 475 ¡æ brittleness, high thermal conductivity and Superplasticity of ferritic stainless steel. Compared with austenitic stainless steel, its yield strength is significantly improved, and its resistance to intergranular corrosion, stress corrosion, corrosion fatigue and abrasion is significantly improved.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The standard austenitic steels like 304 (1.4301) and ferritic steels like 430 are relatively easy to make and to fabricate. As their names imply, they consist mainly of one phase, austenite or ferrite. Although these types are fine for a wide range of applications, there are some important technical weaknesses in both types.

2205 dual-phase steel fasteners have some excellenut mechanical properties, which may be due to the balanced austenitic and ferritic microstructures in the alloy.

Duplex 2507 possesses excellent mechanical properties. Often a light gauge of 2507 material can be used to achieve the same design strength of a thicker nickel alloy.

Though it is important to keep in mind that pitting corrosion can be a concern in chloride solutions when oxidizing media is present. In these conditions, the passive (protective) layer of the Duplex 2205 material may be compromised in localized pitting may occur.

ASTM A815 UNS S32205 Long Radius Elbow is used in turning pipe direction and is also resistant to chloride and sulfide environments. These ASME B16.9 Duplex Stainless Steel Seamless Fittings have a higher chromium content.

The combination of chromium, molybdenum and nitrogen give Duplex 2205 flanges good protection from chloride pitting and crevice corrosion, which makes them useful for marine environments, brackish water, bleaching operations, closed loop water systems and some food processing applications.

Duplex 2205 is a nitrogen enhanced duplex stainless steel designed to solve common corrosion problems encountered with 300 series stainless steels. “Duplex” describes a family of stainless steels that are neither fully austenitic (such as 304 stainless steel) nor purely ferritic (such as 430 stainless steel).
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.48

Super Duplex UNS S32750 /F53 Flanges are made from a super duplex stainless steel grade that has 24% chromium, 3% molybdenum, 6% nickel and carbon, manganese, silicon, sulfur, phosphorus, nitrogen and iron in the composition.

Zeron 100 Threaded Rod are available in hot forged,cold forged and bar stock machined conditions depending upon the order quantity.SA 182 F55 is a forging grade of Alloy 32760 or UNS 32760 which is highly resistant to crevice corrosion and pitting alloy for variety of corrsives. It is 22% chromium duplex stainless steel.

Duplex 2205 stainless steel (ferritic and austenitic) is widely used in applications requiring good corrosion resistance and strength.

The corrosion resistance properties of Duplex 2205 Pipe is much better as compared to alloy grade 316.

Duplex stainless steel 2205 alloy is a compound stainless steel composed of 22% chromium, 2.5% molybdenum and 4.5% nickel nitrogen alloy.
It has high strength, good impact toughness and good overall and local stress corrosion resistance.

The corrosion resistance comes from the addition of alloying material, mostly the chromium content. The ASTM A790 Pipes are resistant to pitting corrosion and crevice corrosion. The pipes could also be electric fusion welded.

Alloy 2205 duplex stainless steel plate has better pitting and crevice corrosion resistance than 316L or 317L austenitic stainless steel in almost all corrosive media.

ASTM A240 UNS S32750 Plate is a stainless steel alloy with excellent resistance to chloride stress-related corrosion cracking.

It reaches the phase balance of austenite and ferrite in roughly same volume fraction.

The combination of chromium, molybdenum and nitrogen gives 2205 good resistance to chloride pitting and crevice corrosion. This resistance is extremely important for services such as marine environments, brackish water, bleaching operations, closed loop water systems and some food processing applications.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.53

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

The 2205 Duplex Stainless Pipe produced in accordance to ASTM A790 specification could be constructed by either a seamless construction or an automatic welding process.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.