2507 super duplex pipe a low coefficient of thermal expansion

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

ASTM A789 A789M Covers Grades of nominal wall thickness, stainless steel tubing for services requiring general corrosion resistance, with particular emphasis on resistance to stress corrosion cracking. These steels are susceptible to embrittlement if used for prolonged periods at elevated temperatures.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Compared to 317L stainless steel, duplex steel has excellent resistance to chloride pitting and crevice corrosion. The alloy has excellent corrosion resistance to seawater and most concentrations of sulfuric acid. In addition, it is resistant to sulfide stress corrosion cracking (sour gas environments)

S31803 has been supplemented by S32205 which has a higher minimum N, CR and Mo.

A Super Duplex 2507 Pipe has outstanding resistance to corrosive and oxidative media.

There are SA 182 F53 S32750 Blind Flanges, socket weld flanges and weld neck flanges in this range of material. The different flanges are used in different applications set ups.

2507 is also used in Flue Gas Scrubbing Equipment, Pulp and Paper Mill Equipment, Offshore Oil production/technology and Oil and gas industry equipment.

Though it is important to keep in mind that pitting corrosion can be a concern in chloride solutions when oxidizing media is present. In these conditions, the passive (protective) layer of the Duplex 2205 material may be compromised in localized pitting may occur.

La tuberia SA 790 UNS S32205 se utiliza para aplicaciones que funcionan en ambientes ligeramente corrosivos, de presion y temperatura ligeramente alta. Aplicacion de tuberia sin costura Duplex S32205 UNS en sistemas de purificacion de agua y manejo de aguas residuales y alta precision.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

The combination of chromium, molybdenum and nitrogen convey the good resistance of 2205 to chloride pitting and crevice corrosion. This resistance is extremely important for services such as marine environments, brackish water, bleaching operations, closed loop water systems and some food processing applications. The high chromium, molybdenum and nitrogen contents of 2205 provide corrosion resistance superior to common stainless steels, such as, 316L and 317L in most environments.

A182 F51 Duplex stainless steel composed of 21% chromium, 2.5% molybdenum and 4.5% nickel-nitrogen alloy. It has high strength, good impact toughness and good overall and local stress corrosion resistance.

The ASTM A790 Duplex Welded Pipes are an example of welded duplex pipe. There are different grades of duplex pipes with different mechanical properties. There are duplex, super duplex and lean categories in the Duplex Pipes varieties. The Seamless Duplex Pipes are both strong and is highly corrosion resistant.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The mechanical strength, corrosion resistance and low temperature toughness of the ASTM A182 F53 Flanges is higher than that of ordinary duplex stainless steels.

In the annealed condition, S31803 contains approximately 40-50% ferrite. S31803 is often referred to as the workhorse grade and is the most widely used grade in duplex stainless steel pipes. The use of S31803 stainless steel pipe should be limited to temperatures below 600¡ãF.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.64

Alloy 2205 duplex stainless steel is an alloy developed from the initial Super Duplex Stainless Steel. It is supplied in the solution annealed condition.

2101 is a low nickel, lean duplex stainless steel possessing both superior strength and chloride stress-corrosion cracking resistance when compared to 300 series stainless steel.

Light gauges of 2507 material can often be used to achieve the same design strength of thicker nickel alloys. Duplex 2507 plate is suitable for applications requiring excellent strength and corrosion resistance. It contains 25% chromium, 4% molybdenum and 7% nickel.

There are different types of flanges such as slip on flanges, socket weld flanges, forged flanges, blind flanges, reducing flanges and many by their functions.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

2507 (UNS S32750) is a super duplex stainless steel designed for applications which require exceptional strength and corrosion resistance. 2507 is a 25% chromium, 4% molybdenum, and 7% nickel alloy resulting in excellent resistance to chloride pitting and crevice corrosion attack.

Duplex steel UNS S31803 hex nuts are widely suitable for the effects of sulphurous gases, especially above 900 degrees Celsius, very low.

Duplex steel sheets are resistant to chloride stress corrosion cracking at 150¡ãC.

Super Duplex UNS S32760 Round Rod has many properties and properties due to the elements present in the chemical composition. Due to these characteristics and properties, these super duplex UNS S32760 round bars are used in a large number of industrial applications.

Duplex¡¯s premium mechanical and chemical properties are slightly offset by its difficulty in formability.

At temperatures above 300¡ãC, the brittle trace components of 2205 precipitate, and at temperatures below -50¡ãC, the trace components undergo a ductile-brittle transition; therefore, this grade of stainless steel is not suitable for use at these temperatures.

Duplex 2205 fasteners are made from standard duplex materials. The material consists of carbon, manganese, silicon, phosphorus, 21% chromium, 2.5% molybdenum, 4.5% nickel and nitrogen.

In S31803, about half of the ferrite grains transform into austenite grains (“islands”) as the material cools to room temperature. The result is a microstructure of approximately 50% austenite and 50% ferrite.

The Benefits of Duplex Stainless Steel are improved Strength, because many duplex grades are as much as two-times stronger than austenitic and ferritic stainless steel grades, high Toughness and Ductility, high Corrosion Resistance, and Cost Effectiveness.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

If the 22cr Duplex Pipe is to be welded, no filler metal is required to be added to the alloy during its welding process.

The flange a182 f53 can also differ in the face type as flat face, raised face and ring type joint flanges.