3-4 inch stainless steel 316 water supplying pipe fittings 45 degree S30400 elbow

ASTM A234 Pipe Fittings include Tee, Concentric reducer, eccentric Reducer, 5D/6D bend, elbow, unions, plugs, cross tee, pipe cap and nipple, ect for use in pressure piping and in pressure vessel fabrication for service at moderate and elevated temperatures.

UNS S31254 Pipe Fittings which is described as a 6 % Mo super austenitic stainless steel. These Duplex Steel UNS S31254 Butt Weld Fittings is a lustrous, silvery colored Molybdenum metal which has an abundance of 1.5 ppm in the earth¡¯s crust. Our Duplex Steel UNS S31254 Pipe Fittings is a high-alloy austenitic stainless steel developed for use in seawater and other aggressive chloride-bearing media. The driving force to the development of these Stainless Steel SMO 254 Buttweld Fittings was the sensitivity to inter-granular corrosion of existing austenitic steels which often contained 0.08 % – 0.10 % carbon. Our Duplex Steel F44 Buttweld Pipe Fittings combines moderately good mechanical strength and high ductility with excellent corrosion resistance in a variety of environments.

ASTM A403 WP347 is a non-heat treatable, austenitic, electric furnace processed grade of stainless steel very similar in composition to Type 321. Type 347 can withstand more severely elevated temperatures than Type 321, as the resulting columbium carbide is more stable and insoluble than the titanium carbide.

Type 304 stainless steel is an austenitic grade that can be drawn very deep. This characteristic has resulted in 304 being the primary grade used in applications such as sinks and pans.

These fittings have earned the 3A symbol, which requires an annual assessment to make certain each product conforms in all respects to the published standard.

The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with good mechanical properties from sub-zero temperatures up to about 550 ¡ãC (1020 ¡ãF) and is approved for pressure vessels with wall temperatures from -10 to 425 ¡ãC (14 to 800 ¡ãF) according to VdTUV-Wbl. 263 and up to 900 ¡ãF (480 ¡ãC) according to ASME Boiler and Pressure Vessel Code.

Nickel 800H reducing butt welded pipe fittings are also used in heat exchangers, dampers, pressure vessels, etc. Our Alloy 800HT Elbow Butt Weld Fittings can also be used in industrial furnaces and heat treating equipment.

The high nickel content gives the alloy resistance to corrosion by many organic and inorganic compounds and also makes it virtually immune to chloride-ion stress-corrosion cracking.

They can also be seamless in nature. The nominal diameter of the seamless fittings ranges from ? inches to 24 inches and the welded fittings range from ? inches to 120 inches in diameter.

They come in different sizes and types; for example, the SS 304 45 degree elbow is used to change the direction of the pipe by a 45 degree angle. Likewise, the UNS S30400 90-degree elbow changes the direction of the pipe by a 90-degree angle. According to customers’ requirements, we can provide exclusive elbows to meet their needs.

ASTM A403 WP317L is a molybdenum bearing, low carbon content “L” grade austenitic stainless steel that provides improved corrosion resistance over 304L and 316L stainless steels. The low carbon provides resistance to sensitization during welding and other thermal processes.

These alloys can function at very high temperatures and in severe mechanical stress environments, and also where high surface stability is required. They have high creep and oxidation resistance.

Alloy 400 is resistance to neutral, alkaline and acid salts is shown, but poor resistance is found with oxidizing acid salts such as ferric chloride.

Class CR fittings are those manufactured to the requirements of MSS SP-43, and they shall have pressure ratings compatible with 13.3. This specification does not apply to cast fittings.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

The material has good strength with 240MPa minimum yield strength and 585MPa minimum tensile strength.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

The Inconel 600 Pipe Fittings are made with high concentrations of chromium, nickel, and molybdenum. This composition of chemicals gives it excellent resistance against all forms of corrosion and oxidation.

Furnace rolls made of this alloy were still in good condition after operating for 8700 hours at 2150 Deg. F. Furnace trays, used to support heavy loads, have been exposed to temperatures up to 2300 Deg. F. in an oxidizing atmosphere without bending or warping.

Corrosion resistance of duplex steel radius fittings provided. Comparable to standard austenitic grades or high alloyed ferrites. While duplex steels have good high temperature oxidation resistance like other duplex stainless steels, embrittlement can occur even at temperatures above 300 degrees Celsius for short periods of time. In case of embrittlement, duplex steel stub joints can only be corrected by a complete solution annealing treatment.

Duplex Elbow Fittings – Duplex steel elbows are installed between two lengths of pipe or tubing, allowing a 180¡ã, 90¡ã or 45¡ã change in direction. End machining is used for butt welding when the two ends are different in size, called a reducer or a reducer elbow. Fitting elbows are available as 1D, 1.5D, 2D, 3D, 5D, 6D, 8D, 10D radius 180¡ã elbows, 90¡ã elbows or 45¡ã elbows as short and long radius elbows.

A403 316L Stainless Steel covers the standard for wrought austenitic stainless steel fittings for pressure piping applications.Compared to grade 316, the pitting resistance properties of ASME B16.9 SS 316L Fitting is much higher.

While there are slight variances to different hot pipe bending methods, nearly all are a form of induction bending.

304 fittings are standard “18/8” stainless steel; it is the most versatile and widely used stainless steel available in a wider range of products, forms and finishes than any other. It has excellent forming and welding characteristics.

Alloy 316H (UNS S31609) is a high carbon modification of Alloy 316 developed for use in elevated temperature service. The alloy has higher strength at elevated temperatures and is used for structural and pressure vessel applications at temperatures above 932¡ãF (500¡ãC). The higher carbon content of 316H also delivers higher tensile and yield strength than 316/316L and its austenitic structure provides excellent toughness down to cryogenic temperatures.

We are a manufacturer, supplier and exporter of Alloy Steel ASTM A234 WP22 Buttweld Fittings that form meaningful connections between multiple pipes of various sizes.

Type 304 is the most popular stainless steel and is a natural choice for its corrosion resistance. It resists rusting in many different environments, but is primarily attacked by chlorides.

This nickel alloy resists the formation of grain-boundary precipitates in the weld heat-affected zone, thus making it suitable for most chemical process applications in the as-welded condition.

Duplex Steel S31803 Pipe End Closures have excellent corrosion resistance and can be used in most environments without protection. Duplex Steel S32205 Fittings End Cap Fittings have the ability to transfer heat efficiently and quickly, making them ideal for heat transfer processes.