3 inch stainless or duplex steel pipe fittings S31803 elbows

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Inconel 625 is a non-magnetic nickel-based alloy. Known for its high strength and toughness, high corrosion and oxidation resistance, and excellent fatigue strength, Inconel 625? also offers a very wide operating temperature range, from cryogenics to 2,000¡ãF (1,093¡ãC).

Inconel 625 elbow works well even in extreme temperatures under high stress.

The seamless fitting is made up of seamless pipe and is available in 12 inches. Whereas the welded SS Equal tee is made up of welded pipe and is available in the size range of ? inches to 72 inches. The welded buttweld fittings are economical when compared to the welded ones. The Stainless steel concentric reducer is used to connect pipe sections or tube sections on the same axis and is usually used when there is a shift in diameter.

Upon exposure to oxidising agents, Inconel 625 is protected naturally by its nickel-chromium matrix.

ASTM A234 covers wrought carbon steel and alloy steel fittings of seamless and welded construction covered by the latest revision of ASME B16.9, B16.11, MSS-SP-79, MSS-SP-83, MSS-SP-95, and MSS-SP-97. These fittings are for use in pressure piping and in pressure vessel fabrication for service at moderate and elevated temperatures.

All kinds of pipe products have DIN, ISO, 3A, SMS, BS, IDF, DS, BPE standard. And pipe fitting: 45¡ã/90¡ã/180¡ãbend series, tee/cross series, concentric(eccentric) series make your pipeline system free connectivity. Each series pipe fittings have weld, clamp, thread and flange four common install ways with your pipe system standard connections.

We are having a team of dynamic and experienced professionals who are observing and supervising the whole process to avoid defects. SS 316/ SS 316L Compression Tube Fittings are suitable to use in chemical, food, beer, decorate, and fluid applications industries. Due to the additional Molybdenum, SS 316 Compression Fittings has better corrosion resistant properties and higher strength than grade 304. We supply best-in-class products, meeting and exceeding our client¡¯s expectations.

Other available materials include silicone, rubber compounds, galvanized steel, and nylon. These sanitary fittings are primarily used to connect hoses to valves, water pumps, and deck drains.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Type 317L is a molybdenum-containing austenitic stainless steel designed to provide better corrosion resistance than Type 316L in highly corrosive process environments, especially those containing chlorides or other halides. The low carbon content allows 317L to be welded without intergranular corrosion due to chromium carbide precipitation at grain boundaries. Type 317L is non-magnetic in the annealed state, but can be made slightly magnetic by soldering.

Sanitary elbows are also classified by length. A large radius elbow has a curvature radius of 1.5 times the pipe¡¯s diameter, but a short radius elbow has a radius equal to the pipe¡¯s diameter

Its high nickel content, a minimum of Ni 72%, combined with its chromium content, provides users of Nickel Alloy 600 a number of benefits including: Good oxidation resistance at high temperatures, Corrosion resistance to both organic and inorganic compounds and Resistance to chloride-ion stress corrosion cracking.

We also accept all orders of CS Elbow A234 WPB up to and including 90 degree to suit your requirements.

ASTM A182 Duplex Steel 2205 Elbow is used in high temperature applications where fluid direction must be changed smoothly without creating too much stress on the bend. There are different types of elbows; short radius, long radius, 90 degree and 45 degree. There are duplex steel Astm A815 fittings are forged stainless steel that can withstand high impact tension. High tension, high strength pipes can use this type of fitting.

ASTM A403 WP317 Pipe Fittings?could be a altered adaptation of?Stainless Steel 317L Pipe Fittings.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

CS Gr A860 WPHY 52 Seamless Butt Weld Fittings have to be heat treated in order to achieve optimum tensile strength properties. The high strength obtained by these seamless or welded Carbon Steel WPHY 52 pipe Fittings could be increased by subjecting the material through processes such as normalizing, quenching, and tempering or stress relieving.

The manufacturing process of A860 WPHY 52 includes heat treatment.

Our ASTM A815 Duplex Steel UNS S32205 Caps are available in a variety of cap shapes, diameters and thread types and are resistant to many industrial acids and seawater.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Type : Seamless / Welded.This steel type contains as low as 0.03% of carbon content and thus reduces its susceptibility to intergranular corrosion.

The SS 316 fittings we sell are made of high quality materials that meet standards. Follow all sizes and dimensions so that our customers can trust our products. ANSI B16.9 Stainless Steel 316 Elbow Weight depends on the nominal size of the pipe, this standard ranges from ?” to 48″.

The machinability of 316 pipe bend is about 60% that of AISI B1112 resulphurised free cutting carbon steel. A free machining version of 316 is available as bar.

Typical application for MONEL K500 which takes advantage of high strength and corrosion resistance are pump shafts, impellers, propeller shafts, valve components for ships and offshore drilling towers, bolting, oil well drill collars and instrumentation components for oil and gas production. It is particularly well suited for centrifugal pumps in the marine industry because of its high strength and low corrosion rates in high-velocity seawater.

Our high quality standard grade 150 lb 304 316 stainless steel threaded fittings are manufactured to the highest standards. All stainless steel pipe fittings are monitored by quality control personnel for strict adherence to applicable standards and codes. These stainless steel fittings are ideal for applications involving potentially corrosive chemicals or liquids. In addition to being resistant to corrosion, stainless steel pipe fittings also prevent contamination, making them useful for many professionals.

Controlled chemical composition limits are applied in the nuclear industry to eliminate the risk of stress corrosion cracking by high purity water containing chloride ions.

Our tee pipe fittings are built of different materials and come in a variety of dimensions and styles. Our forged Tee fittings are created in applicable standards of ASME B 16.9 and ASME 16.11, for large bore and small bore respectively.

Hastelloy B2 is a nickel-molybdenum alloy with significant resistance to reducing environments, such as hydrogen chloride gas and sulfuric, acetic and phosphoric acids. Hastelloy B2 provides resistance to pure sulfuric acid and a number of non-oxidizing acids. The alloy should not be used in oxidizing media or where oxidizing contaminants are available in reducing media. Premature failure may occur if alloy B2 is used where iron or copper is present in a system containing hydrochloric acid.