30 cr13 super duplex sheet 1.4410 1.4501 coil

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

2205 is also more formable under pressure than other ferritic grades. The greater toughness of this grade also outweighs most of its concerns.

Duplex alloys have some of the ferritic stress corrosion cracking resistance of common austenitic stainless alloys and many of the superior formability properties that are more cost effective than high nickel alloys.

The combination of chromium, molybdenum and nitrogen convey the good resistance of 2205 to chloride pitting and crevice corrosion. This resistance is extremely important for services such as marine environments, brackish water, bleaching operations, closed loop water systems and some food processing applications. The high chromium, molybdenum and nitrogen contents of 2205 provide corrosion resistance superior to common stainless steels, such as, 316L and 317L in most environments.

Duplex 2205 is the most widely used duplex (ferritic/austenitic) grade of stainless steel. It is used due to its excellent corrosion resistance and high strength.

Technically, the microstructure of a duplex 2205 tube is approximately 50% ferrite and 50% austenite. As a result, the properties inherited from both categories make this nitrogen-enhanced duplex 2205 seamless pipe ideal for use in industries such as food processing, oilfield piping and heat exchangers, and flue gas desulfurization.

For duplex S31803 nuts, 2 minutes to 3 minutes per mm of wall thickness at temperatures around 1080 degrees Celsius is sufficient to achieve a balanced austenite/ferrite ratio. After annealing, it is recommended to cool these Duplex S32205 nuts as soon as possible.

The A182 F51 material has carbon, 2% manganese, phosphorus, sulfur, 1% silicon, chromium, 4.5% nickel, 2.5% molybdenum and nitrogen it.

Super Duplex UNS S32750 is the most common super duplex grade in the market. UNS S32750 is a duplex stainless steel especially designed for service in aggressive chloride-containing environments.

These grades of super duplex stainless steel fasteners are used when applications require excellent corrosion resistance and strength. Composed of nitrogen, molybdenum and chromium, they have excellent resistance to crevice corrosion and chloride pitting.

S32760 is a super duplex stainless steel with a ferritic-austenitic microstructure.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

This provides the flanges with high corrosion resistance and higher mechanical properties. Please contact us for your orders of F53 flanges.

S32750 Welded Pipes are used in offshore platforms, Mechanical and structural components, sea-water piping, Desalination Plants, Heat exchangers and chemical processing industries.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Duplex steels are characterised by high chromium (19¨C28%) and molybdenum (up to 5%) and lower nickel contents than austenitic stainless steels. The most used duplex stainless steels are the 2205 (22% Chromium, 5% Nickel) and the 2507 (25% Chromium, 7% Nickel); 2507 is known as ¡°super duplex¡± due to its higher resistance to corrosion.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

2507 is also used in Flue Gas Scrubbing Equipment, Pulp and Paper Mill Equipment, Offshore Oil production/technology and Oil and gas industry equipment.

ASTM A240 UNS S32750 plate is suitable for high tension and high corrosion environments.

ASTM A479 Duplex Stainless Steel 1.4462 Punched Gaskets are SCC resistant which is prominent in many applications such as hot water tanks, brewing tanks, desalination plants and processing plants. Therefore, ASTM A479 Duplex Stainless Steel UNS S31803 Lock Washers exhibit the properties of ferritic and austenitic alloys.

2205 dual-phase steel fasteners have some excellenut mechanical properties, which may be due to the balanced austenitic and ferritic microstructures in the alloy.

Duplex stainless steels have a mixed microstructure of austenite and ferrite, the aim being to produce a 50/50 mix, although, in commercial alloys, the mix may be 40/60 respectively.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The astm a182 f53 vs f55 can come in different diameters ranging from ? inches to 48 inches with different pressure classes ranging from class 150 through class 2500.

The duplex microstructure allows this grade of high strength super duplex UNS S32750 bar to have a lower coefficient of thermal expansion and higher thermal conductivity than austenitic steels and is suitable for operating temperatures up to 300¡ãC.

2205 is the standard duplex grade and is more economical than most other duplex grades.

2205 has excellent corrosion properties, and it is well-suited to environments containing chlorides and hydrogen sulphide, for use in oil and gas extraction from sour wells, in refineries and in process solutions contaminated with chlorides.

This category of material includes grades 2205, F51, F53, and F60. Duplex stainless has increased in popularity over the years due to its excellent chemical and mechanical properties versus their basic stainless counterparts, given especially that the cost differences are minimal now as the availability has increased.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

As well as greater tensile and yield strength whilst still providing good ductility and resistance to stress corrosion cracking.

The advantage of the dual-phase structure is that it combines the stress corrosion cracking resistance and high strength of ferritic alloys with the ease of manufacture and corrosion resistance of austenitic stainless steel alloys.

The ASTM A182 F51 flanges refer to standard or non-standard flanges manufactured in accordance with ASTM A182 Grade F51, which is designated with UNS number S31803.

The advantage of the dual-phase structure is that it combines the advantages of ferritic alloys (resistance to stress corrosion cracking and high strength) with the advantages of austenitic alloys (ease of manufacture and corrosion resistance).
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.50

A high molybdenum superaustenitic with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. Suitable for use in pulp mill bleach plants, seawater heat exchangers and chemical process equipment.