304 304L 310S 347 stainless steel pipe fittings 90 degree elbows of high quality

N04400 is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Alloy N04400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acid-like substances), brine, hydrofluoric acid, and sulfuric acid. Other advantages of using this alloy are toughness and high strength over a wide temperature range; it can also be manipulated to be magnetic if desired.

Duplex steel S32205 tee butt welded pipe fittings are often used in chemical process industries: such as sulfuric acid production, nitric acid process, phosphoric acid process, ethylene oxide, polypropylene production, PVC, equipment for handling organic and fatty acids, chemical storage and tankers, thermal switch, etc.

Some types of duplex steel pipe fittings are butt welded fittings, elbows, reducers, couplings, reducers, tees, adapters, joints, and more. Other features of this fitting are good corrosion resistance, pitting and crevice resistance, higher tensile strength, higher yield strength, good toughness, reliability, durability, oxidation resistance, mechanical properties, chemical properties Wait. In addition, it is used in the following applications in chemical industry, pulp and paper industry, condenser, offshore industry, etc.

Hastelloy B2 pipe bend resists the formation of grain boundary carbide precipitates in the weld heat-affected zone, making it suitable for most chemical process applications in the as-welded condition.

Alloy 20 pipe fitting is a chromium-iron-nickel-based, austenitic alloy that comes with excellent corrosion resistance in chemical environments. It contains sulfuric acid and many aggressive media well. The alloy is stabilized with niobium that helps it to resist intergranular corrosion.

Tube caps are used as protective devices designed to protect tube ends of various shapes. The main purpose of using pipe caps is to waterproof connections. They are also used to close the ends of hydraulic or pneumatic pipes and tubes. We supply 1-8 SS304L pipe butt weld pipe fitting cap.

ASTM a403 wp304 pipe bend is done to under control conditions to avoid carburization, decarburization and scaling surface. Heat treatment methods are stress relieving, hardening and annealing which strength the ductility and corrosion resistance properties.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.?Butt-weld and forged fittings are available.Excellent corrosion resistance in many acidic and alkaline environments Especially suitable for reducing conditions. Good ductility and thermal conductivity Ideal for seawater applications.

Our Carbon Steel Butt Welded Pipe Elbow is a carbon steel pipe solution made of forged carbon steel and is mainly used in the high temperature service range.

Monel K500 has about three times the yield strength and twice the tensile strength of Monel 400, and higher mechanical properties can be obtained by cold working or age hardening. Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

Chromium confers resistance to sulfur compounds and also provides resistance to oxidizing conditions at high temperatures or in corrosive solutions.

A welded ASTM A403 Stainless Steel Weld Fittings is made up of pieces of steel plates. Stainless Pipe Fittings are made up of 10% nickel and high chromium content.

ASTM A815 UNS S32760 capis available at our company on a large-scale. The UNS S32760 standard of pipe fittings is considered one of the best in the industry due to its mechanical properties.

ASTM A234 specification does not cover cast welding fittings or fittings machined from castings.

These stainless steel 310S butt welded pipe fittings are used in a variety of applications such as oven fixtures, furnace parts, heat treating chambers, hydrogenation parts, jetting parts, and more. These SS 310S butt weld fittings are also primarily used in the chemical, construction and plumbing industries.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

A stainless steel butt weld cap is a type of pipe fitting that covers the end of a pipe. Since it can have female threads, it can screw on to the male end of the pipe. It can also be welded on to close the end of the pipe. On a weld, if it is a temporary close, or the contractor wants to add to the piping system in the future, he or she should allow additional pipe before closing so the pipe cap can be cut off and the pipe system extended as needed. This way you will not have less pipe than you need and the new fitting can be attached correctly.
A Stainless Steel Butt Weld Cap is used to seal the end of a pipe or a particular butt weld fitting branch or orifice. Typically butt weld pipe caps are used at the end of a piping system or if maintenance is required the pipe cap can blind or isolate the rest of the system to keep it running while maintenance or repairs are performed.

1.4404 SA403 WP316L elbow not necessary. Due to their excellent resistance to intergranular corrosion, these fittings can also be used in the as-welded state. Cold working the alloy will not only increase the strength and hardness of ASTM A403 WP316L fittings, but may also make them slightly magnetic.

Inconel 625 Pipe Fittings are strong and are used in high corrosive applications that need stronger pipes. The material is a nickel chromium molybdenum alloy with niobium in the composition for stabilization. It can operate from cryogenic temperatures up to 1093 degrees Celsius. So the fittings are preferable for applications that require high strength, corrosion resistance and high temperature resistance. The Alloy 625 Buttweld Fittings are used with ease of welding and this is the most used type of fittings. The Inconel UNS N06625 Pipe Elbow is used to turn the pipe away by an angle, usually 45 degrees or 90 degrees. The ANSI B16.9 ASTM B366 625 Inconel Monel Tee can range from ? inches to 48 inches in nominal bore size and it branches a pipe into two.

The alloys used to make these 304 stainless steel socket weld fittings are the most adaptable and widely used. UNS S30400 Short Radius Elbows can be used for high temperatures up to 889 degrees Celsius.

All SA234 WPB Elbow are manufactured in India and produced from strictly European sourced raw material. All ASTM A234 Elbow & Elbow A234 Wpc are manufactured from plate, pressed in two halves with two weld seams.

Super Duplex 2507 Industrial Pipe Fittings, S32750 Pipe Bend, ASME SA 815 S32750 LR Elbow, Super Duplex S32750 Seamless Butt weld Fittings, Super Duplex Steel 1.4410 Eccentric Reducer, Super Duplex S32750 Stub End, S32750 Super Duplex Steel Equal Tee, ANSI B16.9 Super Duplex S32750 Welded Pipe Fittings, SAF 2507 Pipe Fittings Manufacturer in China.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Pipe bending methods will vary based upon the metals used.

HT PIPE is one of the leading manufacturers of different types of high-quality products, such as pipe fittings of different shapes, sizes, thicknesses, etc. On the other hand, we are also a major supplier and exporter of the popular product duplex steel UNS S31803 pipe fittings. Pipe fittings are manufactured to all national and international standards of our organization. There are many kinds of pipe fittings, which are widely used in piping systems for various purposes. They are both used to mount profiled pipes to each other. In this way, liquids, fluids, gases, etc. pass through the pipes without any leakage. Also, fittings come in many sizes, sizes, standards, alloys, grades, etc., but most importantly our Duplex 1.4462 fittings are the most demanded fittings on the market today and for many years.

The combination of very low corrosion rates in high-velocity sea water and high strength make alloy K-500 pipe bend and elbow particularly suitable for shafts of centrifugal pumps in marine service.

We are a manufacturer, supplier and distributor of premium quality Nickel Alloy Forged Elbow. Our primary purpose in providing this product is to understand and meet our customers’ operational requirements. We have supplied these products to large industrial sectors for many years and have earned the trust and satisfaction of our valued customers.

Molybdenum-containing austenitic stainless steel DIN 1.4404 seamless pipe fittings are relatively low in carbon compared to DIN 1.4401 grades, but with small additions of molybdenum and nitrogen, and are used in light or moderately corrosive industries.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

One of the greatest benefits of Inconel 600 fittings is their ability to maintain their performance even at high temperatures. It has a minimum yield strength of 310 MPa and a minimum tensile strength of 655 MPa. It has an elongation of 40%, which is pretty good. Inconel 600 material has a melting point of 1413 degrees Celsius, which makes it ideal for high temperature applications and has a long service life. It can be easily bent and welded, and the size can be customized according to specific requirements.