304 304L 310S 347 stainless steel pipe fittings for drinking water system female elbows for ss pipe connection

Stainless Steel 304 Pipe Fittings are made from seamless steel pipes whereas ERW pipes are made from ERW steel pipes.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

A pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction
or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

A sanitary elbow is a kind of sanitary fitting installed between two lengths of pipe or tubing to allow a change of direction. While these corner fittings are usually a 90¡ã or 45¡ã angle, 22.5¡ã elbows are also available.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

Forged fittings produced in a facility covered by the ASME B16.9 standard must be manufactured in accordance with ASTM A 403. Molybdenum bearing stainless steel 316L fittings are also known as marine grade due to their excellent resistance in marine environments. While the chemical composition of grade 316L is similar to that of grade 316 stainless steel, the main difference between the two alloys is the nitrogen and carbon content.

Commercial applications involve furnace components and fixtures requiring strength and oxidation resistance at temperatures up to 2000 degrees F.

ASTM A234 standard steel pipe fittings have been widely applied in pipeline systems, it includes carbon and alloy steel material.

Stainless Steel 316L is an extra-low carbon version of the grade 316.

We sincerely look forward to providing you with the best quality and most affordable Heat-Resistant Stainless Steel Strips, 321 Stainless Steel Coils, 301 Stainless Steel Coil and bringing the best and fastest economic benefits to your business. Our company is committed to innovation, because we know that only unremitting innovation, the brand can be sustainable development. We may stick on supplying original and good quality parts even a little profit earned. In terms of business innovation, our company shapes the corporate image, implements the brand strategy, establishes the modern corporate culture, and reasonably arranges the network.

In power generation, superheater and reheater tubing has also employed the material 800HT.

Super duplex 2507 / UNS S32750 pipe fittings have great resistive properties to chloride stress corrosion cracking and a high thermal conductivity with a low coefficient of thermal expansion. These pipe fittings have a great resistance to inorganic acids used in dilute hydrochloric acid.

ASTM A403 WP304 Fittings are available in different sizes and shapes and have a pressure rating of 3000#, 6000#, and 9000#.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Duplex stainless steel pipes and fittings are generally less expensive because of the lower proportions of alloying elements used in the manufacture of duplex stainless steels. The yield strength of duplex stainless steel products is higher than that of austenitic stainless steel products, so users can buy duplex pipes and duplex pipe fittings with relatively lower thickness.

Grade 310S Stainless Steel Butt Weld Pipe Fitting contains low Carbon, with higher Nickel and Chromium content curbing Hydrogen sulphide attack, which used in various industries like heat exchangers, furnace parts, shipbuilding, heat treatment baskets, condensers, offshore etc.
The fittings are shaped up and then heated to a high temperature following a rapid cooling closer to the cooling in still air. This rapid cooling adds to the strength of the Stainless Steel 310 Pipe Fittings and makes them much stronger. The SS 310S Fitting is used in industries like the sea water processing, thermal energy generation plants and much domestic piping as well. 310S SS Weld Fittings is used in different pressure classes to cope up with the pressure containment requirement of the application as well.

Tee butt weld fittings are made from A312 dual certified 304/304L or 316/316L stainless steel with milled inside and outside diameters (ID/OD). These stainless steel welded joints meet ASTM A403, ASTM A960, MSS SP-4, ASTM B16.9 (except for walls) and MSS SP-43. Schedule 10 fittings are nominal pipe size (NPS), not pipe outside diameter (OD). Schedule 10 pipe and fittings have wall thicknesses that are nearly twice as thick as standard 16 gauge pipe OD fittings, making them ideal for custom turbine manifold and downpipe fabrication. The increased wall thickness provides additional durability and is less prone to cracking under the high thermal stress of exhaust gas temperatures.

Hastelloy C-276 pipe fittings refer to factory-made wrought nickel alloy fittings manufactured to ASTM B366 UNS N10276. It can be designated as CRHC276(corrosion resistant fittings) or WPHC276(ASME pressure fittings). The fittings can be manufactured from pipe or tube of ASTM B619, B622, B626 UNS N10276, plate, sheet or strip of ASTM B575 UNS N10276, forging or bar of ASTM B564, B462, B472, B574 Gr. N10276. The Hastelloy C-276 fittings are mainly furnished in 3 connection types: butt welding, threaded, socket welding, covering a variety of standard specifications.

Monel 400? sheet is available in thicknesses ranging from .018 to .140″.Butt-weld and forged fittings are available or can be manufactured with short lead times.

Hastelloy C276 fittings are the highest quality finishing fittings for long life, high pressure and zero defects. Hastelloy C276 fittings are alloys that maintain strength, toughness and corrosion resistance in high temperature environments. These alloys are used in a variety of industries and valuable applications such as oil refineries, chemical plants and power generation, nuclear power, aerospace and more.

Stainless steel reducer fittings are similar to couplings, but they can be detached and attached to the pipe and then screwed back to connect them. 316 stainless steel pipe fittings are used in the water pipeline, natural gas, manufacturing and nuclear power plant industries.

The microstructure of duplex stainless steels is split approximately 50:50 between austenite and ferrite, and the balance of these phases provides the following benefits: Higher strength, approximately twice that of Type 304 austenitic stainless steel . This results in a reduction in the thickness of the plates used in fabrication, resulting in reduced weight, which is of particular importance in structural applications such as pressure vessels, storage tanks and bridges, as well as good weldability of thick plates, good low temperature toughness, stress resistance Corrosion cracking is important in many applications including hot water tanks, processing plants, brewing tanks and desalination plants.

ASTM A815 specification covers two general classes, WP and CR, of wrought ferritic, ferritic/austenitic, and martensitic stainless steel fittings of seamless and welded construction. Class WP fittings are subdivided into four subclasses: Classes WP-S, WP-W, WP-WX, and WP-WU. The material for fittings shall consist of forgings, bars, plates, or seamless or welded tubular products.
Teel Industry has grown in the past few decades and there are a variety of products available in the market. ASTM A815 UNS S32750 Pipe Fittings are one of those products and are available in various sizes, shapes, and dimensions. ASTM A815 UNS S32760 Pipe Fittings are designed to be resistant to corrosion and are said to have perfect weldability. These Super Duplex S32750 Buttweld Fittings are resistant to erosion corrosion and fatigue. They have a mixed microstructure of 50% austenitic and 50% ferrite.

A pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction
or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

In seamless fitting form it has size ¡°1/2 to 24¡± and in welded form¡±24 to 96¡± and thickness is available in SCH 10,20,30,40,80,100,120,140,160,XXS. It has dimensions like ANSI/ ASME B16.9, B16.28, MSS-SP-43.

NAS 800H (NCF 800H, UNS N08810)/NAS 800T (UNS N08811) are nickel-iron-chromium alloys that provide high strength and excellent resistance to oxidation and carburization at high temperatures

When we call a steel tee ¡°equal tee¡±, means the branch diameter of this tee is same with the main pipe (Run pipe) diameter of this tee. When we see only one size of tee in its description, it means this tee is the equal tee. for example, 8¡å tee mean the tee main pipe and branch pipe both are 8 inches. Sometimes the equal tee also described 8¡åX8¡å which is the same meaning of 8¡å tee.

SA 815 S31803 Weld Fittings have exceptional chemical properties along with higher strength and good resistance to corrosion. Therefore this grade is used for fitting manufacturing. SA 815 S31803 Long/ Short Radius Elbow display outstanding resistance to pitting, crevice corrosion and have excellent weldability. They are perfect if one is looking for a sturdy pipe with good formability. ASME B16.9 WPS UNS S31803 Elbow also exhibits excellent resistance to acetic and marine environments.

INCONEL Inconel 601 (UNS N06601 / W.Nr. 2.4851) is a general purpose engineering material for applications requiring heat and corrosion resistance. An outstanding feature of INCONEL 601 alloy is its resistance to high temperature oxidation.