304 316 317L stainless steel elbows pipe fittings

Bending a pipe or tube using a stationary die while a counter die bends the material around the stationary die.

It is well known that ASTM A234 steel pipe fittings are used in pressure piping and pressure vessel fabrication for service in medium and high temperature. Fitting materials in this standard include killed steel, forgings, bars, plates, seamless or fusion welded tubular products with filler metals added.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.?Butt-weld and forged fittings are available.Excellent corrosion resistance in many acidic and alkaline environments Especially suitable for reducing conditions. Good ductility and thermal conductivity Ideal for seawater applications.

Nickel Alloy 201 is the low carbon version of Nickel 200 suitable for forming by deep drawing and spinning into combustion boats and the continuous stamping of strip into electronic components. The material is selected for caustic salt evaporators above 315 deg C (600 deg F) as the extended exposure of Nickel 200 above this temperature can lead to the formation of graphite.

Available in a variety of thread types and sizes, head types and lengths, our SS UNS S31600 Pipe Elbow is used to shield all types of pipe from dirt and moisture penetrating the interior of the pipe. Stainless steel 316 butt welded pipe fittings are highly resistant to corrosive activity and carbide precipitation, primarily due to the addition of molybdenum.

Copper Nickel Fittings are also known as Curpo Nickel Fittings (Cu-Ni Fittings), Copper Nickel C71500 (70/30) and UNS C70600 (90/10) Fittings. Simplex offers a full line of copper pipe fittings such as copper-nickel UNS C71500 elbows, copper-nickel (Cu-Ni) 70/30 reducers, copper-nickel tees, copper-nickel stub ends, copper-nickel elbows and copper-nickel crosses .

Type 304 stainless steel is a T 300 Series Stainless Steel austenitic. It has a minimum of 18% chromium and 8% nickel, combined with a maximum of 0.08% carbon. It is defined as a Chromium-Nickel austenitic alloy.304 stainless steel is used for a variety of household and industrial applications such as food handling and processing equipment, screws,[3] machinery parts, utensils, and exhaust manifolds. 304 stainless steel is also used in the architectural field for exterior accents such as water and fire features. It is also a common coil material for vaporizers.

The cast stainless steel pipe fittings such as 304 or 3016l are available in several different types for use in different applications such as threaded, flared, without flare and flange adapters. They provide a safe and leak-proof seal for refineries, chemical processing units, power supply units, and different processing lines. They are suitable for high-pressure applications as well as high temperatures, for instance, nuclear industry and petrochemical, etc.

SA234 WPB Elbow is made up of carbon steel or alloy steel.

These fittings material consist of killed steel, forgings, bars, plates, seamless or HFW (fusion welded) pipe products, with filler metal added.A234 WPB pipe fittings are butt welding ends,commonly used to be welded with the steel pipes of A106,A53,GR.B material,or API 5L GR.B material.

We are manufacturing buttweld seamless and welded Stainless steel 304/ 304L fittings, Stainless steel 304/ 304L flanges and Stainless steel 304/ 304L pipe bends in accordance with ANSI/ASME and DIN standards.

AMS 5754 pipe bend has no yield or tensile strength requirements, but it does require a hardness maximum and stress rupture minimums.

What makes this material a cost-effective alternative is that the nickel content that manufacturers use to produce dual-phase steel butt-welded pipe fittings is lower than that of super-duplex steel. While the reduction in nickel content gives the metal lower mechanical properties, the higher molybdenum and chromium content almost makes up for the lack of nickel in duplex stainless steel fittings.

We manufacture SA403 WP 304 Short Radius and Long Radius Elbows very strong with a minimum yield strength of 205MPa and a minimum tensile strength of 515MPa. These work well in high temperature environments up to 870 degrees Celsius.

Pipe bending methods will vary based upon the metals used.

Stainless steel 310 reducers are a mixture of several metals (this is called an alloy), but mostly iron, which is harder and stronger than iron. Stainless Steel 310S Cross Butt Weld Fittings are typically ferrous alloys with a carbon content between 0.02% and 1.7% by weight. Stainless steel 310 bend butt welded pipe fittings with carbon content above this value are called cast iron, in which the carbon is replaced by other alloy materials.

Alloy 600 / Inconel 600 is combination of Nickel Chromium and Iron providing a standard material for the chemical industry and the automotive engine, aero engine and airframe sectors.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Monel 400 is a nickel-copper alloy with excellent corrosion resistance in a wide variety of media. Monel 400 is characterized by good general corrosion resistance, good weldability and moderate to high strength.

Stainless steel tee is also a kind of pipe fittings, generally there are two kinds. That is, an equal tee, the diameter of the three ends is the same; a reducing tee, the diameter of the branch pipe is different from the other two.

AISI 316 and 316L stainless steels offer increased resistance to atmospheric corrosion, many organic and inorganic chemicals, and food and beverages. 316L has a maximum carbon content of 0.03 and is suitable for welding, while 316 has a moderate carbon content.

It¡¯s also ideal for sensitive industries such as food preparation and pharmaceuticals, as the risk of contamination is much lower.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Monel 400 is widely used in Brine heaters, sea water scrubbers in tanker inert gas systems.

Copper-nickel (Cu-Ni) piping systems are components that connect copper-nickel pipes, copper-nickel fittings, copper-nickel flanges, and valves that process seawater treatment systems.

Process piping systems rarely travel in a straight line from process to process.

WPHY 52 chemical composition includes metals like Manganese, aluminium, phosphorus, sulphur, vanadium, silicon, nickel, titanium, chromium, molybdenum and copper.A few other moved forward ASTM A860 WPHY 52 properties are its expanded solidness, expanded sturdiness, moved forward weldability, great resistance to hydrogen stretch breaking and its exact measurement.

Monel K500 alloy has excellent corrosion resistance, and has higher strength and hardness than Monel 400. This is due to the addition of elements such as Al and Ti to the alloy, and after a certain heat treatment, there are dispersed intermetallic compounds on the substrate.

Manufactured from 304/304L or 316/316L stainless steel with milled inside and outside diameters (ID/OD). These stainless steel welded joints meet ASTM A403, ASTM A960, MSS SP-4, ASTM B16.9 (except for walls), and MSS SP-43.