304 316l 316Ti sanitary stainless steel pipe fittings eccentric elbows

The ASTM A234 WP5 specification consists of wrought carbon steel and alloy steel in seamless and welded form. The ASTM A234 WP5 Pipe Fittings are widely used in pressure vessel fabrication. These fittings have application under moderate to high temperatures and can also be effectively used in pressure piping systems.

These curved products are used in the dairy, food, pharmaceutical, biotechnology and other industries for condensers, heat exchangers, process lines and product transport. We specialize in sanitary certified 316L stainless steel custom swept elbow production and provide mill test reports, our long radius elbows can provide sweeps up to 180 degrees. We offer a wide range of sizes – from 1″ to 10″ OD and tube lengths up to 72″, we can make the size you need.

L2S 90 degree elbows are 304 or 316L stainless steel with a polished finish (No. 7) featuring a butt weld x butt weld connection. This 90 degree elbow is used to change flow direction in many applications for the semiconductor, cosmetics, food, dairy and beverage industries.

Stainless Steel 310s Fittings are austenitic steel products specifically designed for applications requiring corrosion resistance at elevated temperatures. Our ASTM SA403 GR.TP 310S fittings contain high levels of chromium and nickel which contribute to its corrosion resistance, superior strength and corrosion resistance.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Alloy 800HT / Incoloy 800HT is a controlled composition derivative of INCOLOY? alloy 800H (UNS N08810) and is used for the same creep resistant applications, however the combined effects of mechanical and thermal processing of the alloy permit higher design stresses to be incorporated than are permitted for the conventional alloy.

ASME B16.9, ASME B16.28. These Stainless steel 304/ 304L tube/pipe fittings have special quality finishing and duress for long life, high pressure and zero defects.

Stainless steel pipe fittings consist of 10% nickel and high chromium content. Manufacturers of stainless steel fittings produce these fittings with the addition of manganese, phosphorus, carbon, silicon and sulfur in addition to the two main elements.

Depending on the needs of the application, the A234 Wpb Elbow Dimensions vary.

316L stainless steel possesses less carbon and molybdenum than typical 316 steel, which gives the two alloys different characteristics.

In addition to heat resistance, Hastelloy Buttweld Fittings have high resistance to corrosion, pressure and oxidation. Hastelloy pipe fittings also have excellent mechanical properties and are often used in the chemical and aerospace industries.

The stainless steel pipe fittings are available in different cast stainless steel grades including 304, 316, and 316L stainless steel. Different casting grades of stainless steel are suitable for different environments.

we are suppliers of we are manufacturer of pipe fittings, stainless steel pipe fittings, stainless steel erw pipe fittings, stainless steel seamless pipe fittings, stinless steel welded pipe fittings, stainless steel buttweld pipe fittings, stainless steel 304 pipe fittings, stainless steel 304L pipe fittings, stainless steel 310 pipe fittings, stainless steel 316 pipe fittings, stainless steel 316L pipe fittings, stainless steel 321 pipe fittings

Stainless steel reducing tees are very practical in the oil, gas, water pipes, power plants, construction and food industries.

ASTM A403 WP321 pipe fittings mean the pipe fitting which material is Wrought Austenitic Stainless,they are used for the pressure piping systems of moderate and high temperature services.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

WPB is the most commonly used carbon steel pipe fitting material for medium and high temperature application now, it can be made by steel pipe like ASTM A106 Gr.C or steel plate like ASTM A285 GR.C.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Strengthening of super alloy Hastelloy B2 pipe bend is performed by solid-solution hardening, work hardening, and precipitation hardening methods.

30 deg long radius 304 316 321 stainless steel pipe fittings weld S30400 elbow for incredible corrosion resistance in chemical environments containing phosphoric, nitric, sulphuric and chloride acids. However, it is significantly resistant to warm sulfuric acid. The increased power of the tube may also require better forming pressures.

Stainless steel, thanks to its passive chromium oxide coating, does not react with other substances. Thanks to this, it can be freely used in contact with food. Strict HACCP standards require the use of stainless steel in contact with food. All because steel is non-toxic and easy to keep clean. Stainless steel elements can be cleaned with most common detergents and we do not have to worry that the steel surfaces will lose their properties or change their appearance.

The stainless steel pipe fittings are available in different cast stainless steel grades including 304, 316, and 316L stainless steel. Different casting grades of stainless steel are suitable for different environments.

ASTM A234 is the standard specification for pipe fittings of wrought carbon steel and alloy steel for moderate and high-temperature service. Carbon steel pipe fittings manufactured to ASMT A234 are usually furnished in butt-welding form in accordance with ASME B16.9 or ASME B16.49. There are two carbon steel grades: WPB and WPC, of which ASTM A234 WPB is mostly often used in pipeline industry. The A234 WPB butt-welding pipe fittings include elbows, bends, returns, tees, reducers, end caps, crosses, lap joint stub ends, nipples and couplings.
After forming at an elevated temperature, fittings are cooled to a temperature below the critical range under suitable conditions to prevent injurious defects caused by too rapid cooling, but in no case more rapidly than the cooling rate in still air. Heat treatment temperatures specified are metal (part) temperatures. Heat-treated fittings are to be treated according to paragraph 7 in Specification A960/A960M.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

Inconel 600/601/625/718 Butt Weld Heads are a product with many reliable features to prevent cracking and rusting. If the product is free of cracks, the service life of the product will automatically increase.

ASTM A234 WPB Fittings are made up of different material grades.Hot formed WPB, WPC, WPR fittings forming at above 620¡æ[1150¨H] to 980¡æ[1800¨H] no need to be heat treated which they are cooled in still air.

Duplex Elbow Fittings – Duplex steel elbows are installed between two lengths of pipe or tubing, allowing a 180¡ã, 90¡ã or 45¡ã change in direction. End machining is used for butt welding when the two ends are different in size, called a reducer or a reducer elbow. Fitting elbows are available as 1D, 1.5D, 2D, 3D, 5D, 6D, 8D, 10D radius 180¡ã elbows, 90¡ã elbows or 45¡ã elbows as short and long radius elbows.

316 stainless steel pipe bend can be used with seawater, provided precautions are taken to avoid crevice corrosion developing under sediments, precipitation and biofouling, and at designed-in crevices.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance to a wide range of media.