304 317 316 stainless steel construction pipe fittings elbows

WPHY 52 Fittings are recommended be heat treated by one or more of the following procedures: annealing (stress relieving), normalizing, normalizing and tempering, quenching and tempering.Made utilizing high-grade crude materials, these ASTM A860 WPHY Pipe Fittings are anti-corrosive and strong.

Inconel 600 butt welded fittings are also resistant to stress-related corrosion cracking in chloride environments. They are effective against alkaline environments. Inconel 601 fittings also exhibit all of these properties, but due to the addition of aluminum to their chemical composition, they exhibit improved mechanical performance even in extremely hot environments.

1 – 4 inch short type t, sanitary stainless steel ASTM A403 WPS31254 is an austenitic chromium alloy which is the make-up of the steel is 18 percent chromium and 8 percent nickel. Stainless Steel 304 Pipe Fittings has high ductility, excellent forming, spinning and drawing properties.

The ASTM B366 Pipe Fittings that we, Steel Tubes India, manufacture, are covered under the specification for nickel alloy pipe fittings and these include the likes of Hastelloy, Inconel, Nickel Alloy and Monel.

Fully austenitic welds are more prone to cracking during welding. For this reason, Type 316 and Type 316L “matching” filler metals are formulated to cure with a small amount of ferrite in the microstructure to minimize cracking susceptibility.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

The Carbon Steel A234 WPB Smls Reducer is a seamless product that reduces the diameter of the pipeline.Unless specified for carbon steel plates or sheet, the steel may be made to either coarse grain or fine grain practice. Which ASTM A234 WP9 shall be made to fine grain practice.

Alloy B2 also has excellent resistance to pitting and stress corrosion cracking.

HASTELLOY(r) B-2 is a wrought nickel-molybdenum alloy that can be used in the ¡®as welded¡¯ condition.

Designated as UNS N08825 or DIN W.Nr. 2.4858, Incoloy 825 (also known as “Alloy 825”) is an iron-nickel-chromium alloy with additions of molybdenum, copper and titanium. The addition of molybdenum improves its resistance to pitting in water corrosion applications, while the copper content gives it resistance to sulfuric acid. Titanium is added for stability. Alloy 825 has excellent resistance to localized corrosion such as reducing and oxidizing acids, stress corrosion cracking, and pitting and crevice corrosion. It is particularly resistant to sulfuric and phosphoric acid. Incoloy 825 alloy is mainly used in chemical processing, petrochemical pipelines, pollution control equipment, oil and gas well pipelines, nuclear fuel reprocessing, acid production and pickling equipment.

Carbon steel pipes are a popular choice for a variety of applications. Ventilation and steam ducts, municipal ducts and sewage ducts are usually made of carbon steel. It helps if you consider additional properties that may be required in chemicals or temperature. The above details can help you determine which steel is right for you.

Incoloy 800H and 800HT are typically used in parts above 1100¡ãF where creep and fracture resistance is required. The chemical balance allows nickel steel alloys to exhibit excellent resistance to carburizing, oxidizing and nitriding atmospheres. Incoloy 800HT will not become brittle even after prolonged use in the 1200-1600¡ã F range where many stainless steels become brittle. 800HT exhibits the excellent cold forming qualities normally associated with Nichrome.

INCONEL Inconel 601 (UNS N06601 / W.Nr. 2.4851) is a general purpose engineering material for applications requiring heat and corrosion resistance. An outstanding feature of INCONEL 601 alloy is its resistance to high temperature oxidation.

Duplex 2507 is a super duplex stainless steel designed for applications which demand exceptional strength and corrosion resistance. Alloy 2507 has 25% chromium, 4% molybdenum, and 7% nickel. This high molybdenum, chromium and nitrogen content results in excellent resistance to chloride pitting and crevice corrosion attack and the duplex structure provides 2507 with exceptional resistance to chloride stress corrosion cracking.

ASTM A182 Duplex Steel 2205 Elbow is used in high temperature applications where fluid direction must be changed smoothly without creating too much stress on the bend. There are different types of elbows; short radius, long radius, 90 degree and 45 degree. There are duplex steel Astm A815 fittings are forged stainless steel that can withstand high impact tension. High tension, high strength pipes can use this type of fitting.

ASTM A403 WP321 is a titanium stabilized austenitic stainless steel with good general corrosion resistance. It has excellent resistance to intergranular corrosion after exposure to temperatures in the chromium carbide precipitation range of 800¨C1500¡ãF (427¨C816¡ãC). The alloy resists oxidation to 1500¡ãF (816¡ãC) and has higher creep and stress rupture properties than alloys 304 and 304L. It also possesses good low temperature toughness.

The A420 Grade WPL6 fitting is used in pipelines in the paper and pulp industries, condensers, sea water, marine engineering, waste water management and pollution control systems.

Super Duplex 2507 Industrial Pipe Fittings, S32750 Pipe Bend, ASME SA 815 S32750 LR Elbow, Super Duplex S32750 Seamless Butt weld Fittings, Super Duplex Steel 1.4410 Eccentric Reducer, Super Duplex S32750 Stub End, S32750 Super Duplex Steel Equal Tee, ANSI B16.9 Super Duplex S32750 Welded Pipe Fittings, SAF 2507 Pipe Fittings Manufacturer in China.

It is also one of the few materials that withstands the corrosive effects of wet chlorine gas, hypochlorite, and chlorine dioxide.

Monel 400? can be used in temperatures up to 1000 oF. Monel K-500 is basically a better version of 400 and has higher strength and hardness.

Sanitary elbows are typically made of the stainless steel grade 304 or 316 to provide a sterile and corrosion-free surface.

we manufacture wide range of ASTM A234 Grade WPB Seamless Fittings such as ASTM/ASME A234 Wpb Reducer & A234 Gr WPB Fittings, ASTM A234 Gr WPB Elbow etc.

Monel 400 is a Nickel-Copper alloy, resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.

This alloy is more resistant to nickel under reducing conditions and more resistant than copper under oxidizing conditions, it does show however better resistance to reducing media than oxidizing.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Inconel 601 has good resistance to stress corrosion cracking. Due to the control of carbon content and grain size, 601 has high creep rupture strength, so it is recommended to use 601 in the field above 500 ¡ãC.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

316L is popular for pharmaceutical and photography equipment because it can withstand welding and corrosive chemicals.

ASTM A403 WP316 Fittings are a grade of pipe fittings that are made up of a high oxidation resistant material. This material is also corrosion resistive, pitting resistive and can withstand strong chemicals and acids. The high temperature and pressure tolerance of this material makes the A403 WP316 Elbow to perform better under the corrosive high pressure curvatures of piping. The corrosion in fluid direction changing joints is high. Due to the impact of the fluid flow, the fitting might break if there was corrosion and or thermal expansion.