304 or 316l stainless steel pipe fittings tee fittings m profile

The combined effects of mechanical and thermal processing of Incoloy Alloy 800HT permit higher design stresses to be incorporated than are permitted for the conventional Alloy 800H.

The deformation activation energy is low during superplastic deformation, and the process may be controlled by diffusion.

C22 can be hot worked or cold worked. However, C22 work-hardens rapidly. Therefore, cold working must often be performed in stages with intervening anneals. Parts should be annealed after cold working.

These fittings are for use in pressure piping and in pressure vessel fabrication for service at moderate and elevated temperatures.

Incoloy 800 is an alloy of Nickel, Iron, and Chromium alloy with high strength and excellent resistance to oxidation and carburization in high-temperature exposure. Incoloy 800H and 800 HT are also Nickel, Iron, and Chromium alloy which is used for high-temperature structural application. Incoloy 800HT has further modifications to the combined titanium and aluminium levels which ensures excellent high-temperature properties.

Duplex UNS S32205 Pipe Elbows are used where the direction of the pipe must be changed and there is less stress on the pipe wall. Elbow is one of the most commonly used accessories. Most fittings have nominal bores ranging from 1/8″ to 42″.

ncoloy 800H Forgings have good strength and excellent resistance to oxidation, sulfidation and carburization at elevated temperatures.

Strengthening of super alloy Hastelloy B2 pipe bend is performed by solid-solution hardening, work hardening, and precipitation hardening methods.

Inconel 625 Fittings are made up of an nickel alloy that is non ¨C magnetic. It has high toughness and strength. The material is corrosion resistant and oxidation resistant.

It has very good resistance to stress corrosion cracking Due to the control of carbon content and grain size, 601 has high creep rupture strength, so 601 is recommended for use in areas above 500 ¡ãC.

The accumulation of copper to the grade 904L alloys makes it resistant to corrosion, especially phosphoric, acidic, and sulphuric acid.It Is A Kind Of Corrosion And Heat Resistant Steel.

The stainless steel pipe fittings are available in different cast stainless steel grades including 304, 316, and 316L stainless steel. Different casting grades of stainless steel are suitable for different environments.

Stainless steel grade 304 is the most commonly used stainless steel. Stainless steel grade 304N has better corrosion resistance than grade 302, and is mostly non-magnetic in nature; however when cold worked it acquires a slightly magnetic quality.

This true alloy is very ductile. Therefore, fittings can be formed into any shape, including elbow stainless steel 304, which can be angled at 45 degrees or 90 degrees.

S32205 is a duplex stainless steel with twice the strength of austenitic stainless steel. Duplex stainless steel composed of 21% chromium, 2.5% molybdenum and 4.5% nickel-nitrogen alloy. It has high strength, good impact toughness and good overall and local stress corrosion resistance. The yield strength of duplex stainless steels is twice that of austenitic stainless steels, a feature that allows designers to reduce weight when designing products, making this alloy more affordable than 316, 317L. This alloy is particularly suitable for use in the -50¡ãF/+600¡ãF temperature range. For applications outside this temperature range, this alloy can also be considered, but there are some limitations, especially when applied to welded structures. Duplex stainless steel has twice the compressive strength compared to austenitic stainless steel, and designers can reduce its weight compared to 316L and 317L. Alloy 2205 is particularly suitable for use in the -50¡ãF/+600¡ãF temperature range, and can also be used at lower temperatures under severe restrictions (especially for welded structures).

ASTM A234 WPB Sch 40 Fittings covers carbon steel fittings of welded and seamless development secured by the foremost later revision of ASME B16.9, B16.11, MSS-SP-79, MSS-SP-83, MSS-SP-95, and MSS-SP-97. A234 WPB Carbon Steel Fittings to boot exceedingly corrosion-resistant has low string contact and profitable where high alloyed steel is required.

Nickel alloy 800 unequal tee fittings are considered suitable for metallurgical industry, shipping industry, pulp and paper industry, food industry, oil and gas industry, energy industry, chemical industry, seawater desalination industry, etc. With the help of using us, we provide a range of pipe fittings which are also factory made with an excellent well-established infrastructure facilitated by quality and current machines.

The corrosion resistance of this alloy alone makes duplex stainless steel pipe fittings a better contender for challenging applications. Industries such as oil and gas and petrochemicals are high pressure environments. These industries need products like ASTM A815 UNS S31803 elbows that are not only standardized but also durable.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Fittings such as ASTM A815 UNS S32205 Long Radius Elbows are used in seawater, marine and highly corrosive applications such as the oil, oil and gas, and offshore oil drilling industries because the duplex material is strong and resistant to corrosion by acid and chloride ions.

316 pipe fittings are commonly used in commercial and industrial piping systems in chemical plants, pulp & paper, petroleum, food & beverage, sanitary, steam systems, and general industrial processes that are subject to various stressors.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.?Butt-weld and forged fittings are available.Excellent corrosion resistance in many acidic and alkaline environments Especially suitable for reducing conditions. Good ductility and thermal conductivity Ideal for seawater applications.

Tube caps are used as protective devices designed to protect tube ends of various shapes. The main purpose of using pipe caps is to waterproof connections. They are also used to close the ends of hydraulic or pneumatic pipes and tubes. We supply 1-8 SS304L pipe butt weld pipe fitting cap.

These Buttweld 45 Degree Weld Elbows are manufactured to very high tolerances via hydroforming. Hydroforming results in a more uniform fitting that is easier to weld and polish.

Our inventory includes but is not limited to carbon steel, stainless steel, PVC S80, CPVC S80 and specialty alloy materials. Our highly trained staff will help you with piping, flanges, fittings, structural shapes and related components.

A stainless steel butt weld cap is a type of pipe fitting that covers the end of a pipe. Since it can have female threads, it can screw on to the male end of the pipe. It can also be welded on to close the end of the pipe. On a weld, if it is a temporary close, or the contractor wants to add to the piping system in the future, he or she should allow additional pipe before closing so the pipe cap can be cut off and the pipe system extended as needed. This way you will not have less pipe than you need and the new fitting can be attached correctly.
A Stainless Steel Butt Weld Cap is used to seal the end of a pipe or a particular butt weld fitting branch or orifice. Typically butt weld pipe caps are used at the end of a piping system or if maintenance is required the pipe cap can blind or isolate the rest of the system to keep it running while maintenance or repairs are performed.

HASTELLOY C-276 alloy (UNS N10276) was the first wrought, nickel-chromiummolybdenum material to alleviate concerns over welding (by virtue of extremely low carbon
and silicon contents).

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance in a wide range of marine and chemical environments and has freedom from chloride induced stress-corrosion cracking.

304 and 304L are austenitic alloys, which means that iron carbide or a non-magnetic solid solution of carbon in iron is used to impart corrosion resistance to this stainless steel. We manufacture stainless steel 304/304L forged fittings in socket weld and threaded forms as well as stainless steel 304/304L elbows in standard and non-standard sizes with bend radii from 1D to 10D. We offer stock delivery of Stainless Steel 304/ 304L Fittings, Stainless Steel 304/ 304L Flanges and Stainless Steel 304/ 304L Bends in a variety of standard sizes and types.