304 sanitary stainless steel concentric tee

A pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction
or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

C-276 alloy is normally solution heat-treated at 2050¡ãF (1121¡ãC) and rapid quenched. If possible, parts which have been hot-formed should be solution heat-treated prior to final fabrication or installation.

As an important category of pipe fittings, pipe caps are in great demand. If a solvent welded cap is used as a future connection point, you must leave a few inches of tubing in front of the cap; when the cap is cut off for future connections, you must leave enough tubing to allow the new fitting to be glued to it. We offer 1-4 inch bw ss pipe fittings 304L cap.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Inconel 625 Pipe Fittings are strong and are used in high corrosive applications that need stronger pipes. The material is a nickel chromium molybdenum alloy with niobium in the composition for stabilization. It can operate from cryogenic temperatures up to 1093 degrees Celsius. So the fittings are preferable for applications that require high strength, corrosion resistance and high temperature resistance. The Alloy 625 Buttweld Fittings are used with ease of welding and this is the most used type of fittings. The Inconel UNS N06625 Pipe Elbow is used to turn the pipe away by an angle, usually 45 degrees or 90 degrees. The ANSI B16.9 ASTM B366 625 Inconel Monel Tee can range from ? inches to 48 inches in nominal bore size and it branches a pipe into two.

In the annealed condition, stainless steel 317L fittings are non-magnetic. Although fittings manufactured from Grade 317L cannot be hardened by heat treatment, the material will harden by cold working. 317L fittings can be easily welded and machined by traditional shop fabrication methods. No post weld heat treatment is required for these fittings. Generally, grade 317 stainless steel can be welded using fusion welding and resistance welding methods, but for these 317L stainless steel fittings, oxyacetylene welding is not the preferred method. For best results, use 317L filler metal or AWS E/ER317 or .

Super duplex 2507 / UNS S32750 pipe fittings have great resistive properties to chloride stress corrosion cracking and a high thermal conductivity with a low coefficient of thermal expansion. These pipe fittings have a great resistance to inorganic acids used in dilute hydrochloric acid.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Stainless grade S31254 is a very high-end austenitic stainless steel.
Grade S31254 is reported to be a cost-effective alternative to high nickel and titanium alloys for some applications.

Hastelloy C22 pipe fittings is a combination of versatile austenitic nickel, chromium, molybdenum, and tungsten alloy. This alloy enhances the resistance to corrosion, petting, and oxidations.

Its high nickel content, a minimum of Ni 72%, combined with its chromium content, provides users of Nickel Alloy 600 a number of benefits including: Good oxidation resistance at high temperatures, Corrosion resistance to both organic and inorganic compounds and Resistance to chloride-ion stress corrosion cracking.

Hastelloy B2 is a nickel-molybdenum alloy with significant resistance to reducing environments, such as hydrogen chloride gas and sulfuric, acetic and phosphoric acids.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Duplex fittings are used in different types of piping applications. 2205 is a standard duplex steel with 21% chromium. The material is strong, twice as strong as austenitic steel types. Different standards such as ASME B16.9, B16.28 and B16.25 govern the dimensions. Depending on the type of fitting, the nominal bore diameter of the fitting can also vary.

Designated as UNS N08825 or DIN W.Nr. 2.4858, Incoloy 825 (also known as “Alloy 825”) is an iron-nickel-chromium alloy with additions of molybdenum, copper and titanium. The addition of molybdenum improves its resistance to pitting in water corrosion applications, while the copper content gives it resistance to sulfuric acid. Titanium is added for stability. Alloy 825 has excellent resistance to localized corrosion such as reducing and oxidizing acids, stress corrosion cracking, and pitting and crevice corrosion. It is particularly resistant to sulfuric and phosphoric acid. Incoloy 825 alloy is mainly used in chemical processing, petrochemical pipelines, pollution control equipment, oil and gas well pipelines, nuclear fuel reprocessing, acid production and pickling equipment.

Monel K500 alloy has excellent corrosion resistance, and has higher strength and hardness than Monel 400. This is due to the addition of elements such as Al and Ti to the alloy, and after a certain heat treatment, there are dispersed intermetallic compounds on the substrate.

ASTM B 366 Hastelloy C276 Welded Outlets are used for butt welded branch connections where the pipeline is in critical/high pressure service. It is designed to minimize stress concentrations and provide overall reinforcement.

These caps provide a safe cushion against any type of cracks, chips and cracks on the pipes. We offer 1-8 in female pipe fittings duplex 2205 pipe cap.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

321 stainless steel, also known as UNS S32100 and Grade 321, is primarily comprised of 17% to 19% chromium, 12% nickel, .25% to 1% silicon, 2% maximum manganese, traces of phosphorus and sulfur, 5 x (c + n) .70% titanium, with the balance being iron. With regards to corrosion resistance, 321 Stainless Steel is equivalent to Grade 304 in the annealed condition and is superior if the application involves service in the 797¡ã to 1652¡ã F range. 321 Stainless Steel combines high strength, resistance to scaling and phase stability with resistance to subsequent aqueous corrosion.
UNS S32100 Reducing Tee is preferred due to its ability to work in high pressure and temperature even at a higher temperature.
Stainless Steel 321 / 321H Pipe Fittings are used in filtration, refrigeration, oil, gas, petrochemical and in offshore oil drilling industries. The material has chromium, nickel, titanium and other elements along with carbon. The 321H has higher carbon than the other versions. There are different types of fittings such as the 321/321H Stainless Steel Buttweld Fittings which are most commonly used but there are also the seamless fittings. The Stainless Steel UNS S32100 Pipe Elbow is a fitting type that is used in high temperature applications to change direction of flow.

Since the Stainless steel 90 degree elbow is sold as per pipe fitting it is important to know the pipe schedule this helps in matching the ID of the fitting to that of the pipe. 150# stainless steel socket weld fittings are available in both seamless and welded conditions.

These fittings contain small amounts of additional copper, titanium and molybdenum, which improve their chemical and mechanical properties. Our UNS N08825 Incoloy 825 elbows have been designed to provide increased resistance to crevice and pitting corrosion and to operate smoothly at moderately elevated temperatures.

These fittings material consist of killed steel, forgings, bars, plates, seamless or HFW (fusion welded) pipe products, with filler metal added.A234 WPB pipe fittings are butt welding ends,commonly used to be welded with the steel pipes of A106,A53,GR.B material,or API 5L GR.B material.

Inconel Alloy 600 is designated as UNS N06600 and Werkstoff Number 2.4816.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

There are many different types of 316 stainless steel. Some common types are the L, F, N, and H variants. Each is slightly different and each serves a different purpose. “L” means 316L steel has less carbon than 316.

They primarily provide resistance to chloride stress corrosion and chloride pitting corrosion. They have higher chromium and molybdenum content than other austenitic stainless steels.

Reducers have excellent weldability. Due to the nickel content, Inconel reducers have good formability and exhibit excellent weldability.

Super Duplex 2507 Industrial Pipe Fittings, S32750 Pipe Bend, ASME SA 815 S32750 LR Elbow, Super Duplex S32750 Seamless Butt weld Fittings, Super Duplex Steel 1.4410 Eccentric Reducer, Super Duplex S32750 Stub End, S32750 Super Duplex Steel Equal Tee, ANSI B16.9 Super Duplex S32750 Welded Pipe Fittings, SAF 2507 Pipe Fittings Manufacturer in China.