304 stainless steel pipe fittings for drinking water system/male tee for ss pipe connection

Pipe fittings of ASTM A420 WPL6 are widely utilized in pressure piping and pressure vessel service at low-temperatures.ASTM A420 is the standard specification for pipe fittings of carbon steel and alloy steel used for low temperature services.

Duplex fittings have medium performance. However, the mechanical properties of duplex steels are much higher compared to austenitic alloys such as 304. What makes this material a cost-effective alternative is that the nickel content that manufacturers use to produce dual-phase steel butt-welded pipe fittings is lower than that of super-duplex steel.

Stainless steel 304 elbow fittings are also used in shipbuilding, pressure vessels, boilers, construction, wind energy engineering, etc. Our stainless steel 304L tee fittings are also difficult to dilute sulfuric acid solutions to 120 degrees Fahrenheit.

The Stainless Steel 304 Pipe Fittings are also strong. They have 205MPa minimum yield strength and 515MPa minimum tensile strength.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

It is well known that ASTM A234 steel pipe fittings are used in pressure piping and pressure vessel fabrication for service in medium and high temperature. Fitting materials in this standard include killed steel, forgings, bars, plates, seamless or fusion welded tubular products with filler metals added.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

Incoloy 800H and 800HT are typically used in parts above 1100¡ãF where creep and fracture resistance is required. The chemical balance allows nickel steel alloys to exhibit excellent resistance to carburizing, oxidizing and nitriding atmospheres. Incoloy 800HT will not become brittle even after prolonged use in the 1200-1600¡ã F range where many stainless steels become brittle. 800HT exhibits the excellent cold forming qualities normally associated with Nichrome.

Inconel 601 (UNS N06601 ) nickel-based alloy density: 8.42 g/cm3 (grams/cubic centimeter).

We are also shareholders of carbon steel pipe fittings, such as carbon steel butt welding elbows, butt welding carbon steel crosses, butt welding carbon steel tees, butt welding carbon steel end caps, carbon steel butt welding short pipe ends, etc.

Inconel 625 Pipe Fittings are strong and are used in high corrosive applications that need stronger pipes. The material is a nickel chromium molybdenum alloy with niobium in the composition for stabilization. It can operate from cryogenic temperatures up to 1093 degrees Celsius. So the fittings are preferable for applications that require high strength, corrosion resistance and high temperature resistance. The Alloy 625 Buttweld Fittings are used with ease of welding and this is the most used type of fittings. The Inconel UNS N06625 Pipe Elbow is used to turn the pipe away by an angle, usually 45 degrees or 90 degrees. The ANSI B16.9 ASTM B366 625 Inconel Monel Tee can range from ? inches to 48 inches in nominal bore size and it branches a pipe into two.

Inconel600 is suitable for welding with the same material or other metals by any traditional welding process, such as tungsten electrode inert gas welding, plasma arc welding, manual sub-arc welding, metal inert gas shielded welding, molten arc inert gas shielded welding, and pulsed arc welding. Welding is the preferred solution. When using manual arc welding, it is recommended to use a shielding gas mixed with various components (Ar+He+H2+CO2).
Welding of Incoloy 825 must be carried out in the annealed condition and cleaned with a stainless steel wire brush to remove stains, dust and various markings. When welding the root of the weld, extreme care must be taken (Argon 99.99) to obtain the best quality of the root weld so that the weld does not produce oxides after the root has been welded. Color from the weld heat-affected zone should be removed with a stainless steel brush while the weld area is not cool.

Hastelloy C2000 pipe fittings is a nickel-chromium-molybdenum alloy. It is most commonly available in wrought forms at the mill level. Hastelloy C2000 can be used in applications requiring high metallurgical stability in reducing or oxidizing atmosphere. It is also sed in chemical process equipment applications.

Grade 310S Stainless Steel Butt Weld Pipe Fitting contains low Carbon, with higher Nickel and Chromium content curbing Hydrogen sulphide attack, which used in various industries like heat exchangers, furnace parts, shipbuilding, heat treatment baskets, condensers, offshore etc.
The fittings are shaped up and then heated to a high temperature following a rapid cooling closer to the cooling in still air. This rapid cooling adds to the strength of the Stainless Steel 310 Pipe Fittings and makes them much stronger. The SS 310S Fitting is used in industries like the sea water processing, thermal energy generation plants and much domestic piping as well. 310S SS Weld Fittings is used in different pressure classes to cope up with the pressure containment requirement of the application as well.

These A234 WP9 Alloy Steel Reducer are relevant to use in low-pressure product flow services, however, their working pressure can vary depending upon the pipe’s built.This is because of the decreased inclination to accelerate malicious inter-metallic stages in these Alloy Steel WP9 Stub End, subsequently, bearing it more noteworthy flexibility than different alloys amid and following different thermal cycling conditions.

1 – 4 inch short type t, sanitary stainless steel ASTM A403 WPS31254 is an austenitic chromium alloy which is the make-up of the steel is 18 percent chromium and 8 percent nickel. Stainless Steel 304 Pipe Fittings has high ductility, excellent forming, spinning and drawing properties.

The SS 304 Elbow is one of the key components in the pressure piping system. It basically helps to change the direction of flow in the pipe run. These ASTM A403 Gr WP304 Buttweld Fittings help to connect two pipes with the same or different nominal diameters so as to change the fluid direction by 45 or 90 degrees.

Grade 430 is a ferritic, straight chromium, non-hardenable grade, combining good corrosion resistance and formability characteristics with useful mechanical properties. Its ability to resist nitric acid attack permits its use in specific chemical applications but automotive trim and appliance components represents its largest fields of application.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

INCONEL Alloy 600 (UNS N06600 W.Nr. 2.4816) is a standard engineering material for applications which require resistance to corrosion and heat.

Unlike the bends, the elbows can reduce the pressure applied on the walls when turning the fluid flow direction.Fittings made from WPHY 52 material are known to have a long work life, durable, tough and hard. The WPHY 52 properties make these fittings a perfect cost saving solution for a variety of industries.

UNS S31600 material is considered a marine grade pipe and is designed without any welds or seams. The grade performs well in different aqueous media and shows resistance to pitting corrosion by chlorides and any contaminants. The superior chemistry of this grade prevents long-term plumbing in water bodies. However, marine-grade pipelines are susceptible to warm waters.

Although 316L contains less carbon, 316 and 316L stainless steels cost approximately the same.

Meanwhile, these Duplex Steel S32205 Cross Pipe Fittings are also available to our customers in different sizes and shapes. Duplex steel S31803 bent butt welded pipe fittings generally perform well in environments that cause premature failure of austenitic grades. Although duplex steel S32205 short end butt welded pipe fittings have good high temperature oxidation resistance, this grade – like other duplex stainless steels – can experience embrittlement if held at temperatures above 300 degrees Celsius for even short periods of time. If embrittled, duplex S31803 end caps can only be corrected by full solution annealing. Duplex S32205 Disc Lid Fittings are almost never used above 300 degrees Celsius.

One of the major concerns about the SS 304 Fitting is its low cost compared to other high end alloy material counterparts.All A403 gr WP304 Buttweld Elbow and 304 Pipe Fittings should experience heat-treatment.

A403 is applicable in various applications like car headers, machinery parts, screws and also food handling equipment. We offer these DIN 1.4301 Stainless Steel Butt Weld Fittings in different forms like Tees, Reducers, Cross, Stub Bends, Elbow and End caps. SS UNS S30400 Butt Weld Pipe Elbow execute excellent forming and welding properties. This type of steel also shows excellent oxidation resistant properties. We develop all our products under international standards in top notch infrastructure facility to attain highest scales of quality.

1.4529 German numeral code. Is a super duplex stainless steel, the main components: 20Cr-25Ni-6Mo-1Cu-0.2N corresponding to the United States: N08926, 254SMo…
1.4529 (UNS N08926) has very high resistance to pitting and crevice corrosion in halide media and in acidic environments containing sulfur and hydrogen
It can effectively resist chloride ion stress corrosion, and also has good corrosion resistance and good stability in oxidizing and reducing media.
The mechanical properties are slightly better than 904L, and it can be used in the manufacture of pressure vessels from -196 to 400 ¡ãC.

Owing to its high corrosion resistance– especially pitting and crevice resistance, Inconel 625 is an ideal for high saline, underwater applications.

Copper Nickel Fittings are also known as Curpo Nickel Fittings (Cu-Ni Fittings), Copper Nickel C71500 (70/30) and UNS C70600 (90/10) Fittings. Simplex offers a full line of copper pipe fittings such as copper-nickel UNS C71500 elbows, copper-nickel (Cu-Ni) 70/30 reducers, copper-nickel tees, copper-nickel stub ends, copper-nickel elbows and copper-nickel crosses .

Bending a pipe or tube using a stationary die while a counter die bends the material around the stationary die.