316 stainless steel flat bar weight SS 316 Bar stock

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

Inconel 718 is a nickel-chromium-based alloy that is commonly used in high-temperature applications such as aerospace and gas turbines. One of the most important factors in the production of ASTM B670 Inconel 718 Sheet is the plate rolling process. There are two main types of Inconel 718 plates available on the market: hot rolled and cold rolled plates.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

304 Piping Spools are made of 304 Stainless Steel, a common and popular material in many industrial applications that require resistance to corrosion and oxidation. These S30400 Piping Spools are prefabricated using specialized machinery and processes, which ensure that they are highly accurate and reliable.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

ASME B36.19M is the standard specification for stainless steel pipes, which specifies the dimensions, tolerance, and manufacturing requirements for both welded and seamless pipes.

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

These stainless steel pipe fittings have excellent corrosion resistance and dimensional accuracy along with close tolerances. Our range of pipe fittings include butt weld pipe fitting & instrumentation and ferrule fitting are offered in different sizes, we also provide customization as per the requirements of clients.

ASTM A182 F321 Flanges
Featuring 304 stainless steel for very good corrosion resistance, this GRAINGER APPROVED weld neck flange can be attached to a system via a circumferential weld at the neck. The welded area can be easily examined by radiography. Matched pipe and flange bore reduces turbulence and erosion inside the pipeline. Flange is excellent for use in your critical applications and is ideal for use with air, water, oil, natural gas, and steam.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Fasteners vary in size, shape, grade and specification. The most commonly used fasteners are bolts and nuts. Carbon steel washers are also commonly used to tightly mate nuts with bolt heads and mating surfaces.

Hastelloy B3 Lap Joint Flanges has a special chemistry designed to achieve a level of thermal stability greatly superior to that of its predecessors, e.g. B2 alloy.

The yield strength of this material is almost two times that of the usually used austenitic stainless steel grade.

ANSI B16.5 304 316 317 Stainless Steel Forged Weld Neck Flange
Featuring 304 stainless steel for very good corrosion resistance, this GRAINGER APPROVED weld neck flange can be attached to a system via a circumferential weld at the neck. The welded area can be easily examined by radiography. Matched pipe and flange bore reduces turbulence and erosion inside the pipeline. Flange is excellent for use in your critical applications and is ideal for use with air, water, oil, natural gas, and steam.

Chrome Moly Alloy A182 F11 Flanges is thus manufactured by regal sales corporation as it is the most reputed and well-known firm in the steel industry.

Both alloys have the same chemical composition as Alloy 800 plate (UNS N08800), but the carbon content is higher in both grades – (0.05 – 0.10%) in Alloy 800H and (0.06 in Alloy 800H) – 0.10% ) 800HT board.

ASTM B564?INCOLOY 825 FLANGES Incoloy 825 Flanges are one such type of flanges that have outstanding resistance to oxidizing as well as reducing acids. They are fabricated to improve their resistance to corrosion and are clean to weld

ASTM A182 F12 round bar is commonly used in different industries, such as air-conditioning industry, aluminum industry, boiler industry, steel industry, cement industry, construction industry, etc. ASME SA 182 F12 bar stock is available in a variety of sizes to meet different customer requirements.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

Duplex 2507 (UNS S32750) is a super duplex stainless steel with 25% chromium, 4% molybdenum, and 7% nickel designed for demanding applications which require exceptional strength and corrosion resistance, such as chemical process, petrochemical, and seawater equipment.

Alloy 800H plate (UNS N08810 plate) is a widely used structural material for equipment that must have high strength and resist carburization, oxidation and other detrimental effects of high temperature exposure.

Hastelloy Nickel Alloy B2 is a very chemically resistant alloy with high resistance to pitting and stress corrosion cracking in the heat affected zone. In particular, this alloy performs well in harsh environments such as sulfuric acid, hydrogen chloride and phosphoric acid. Alloy B is also known as WNR 2.4617 bolts and we offer these types of alloys in all material grades, gauges and sizes.

Alloy steel F12 square bars can withstand very high temperatures with minimal product aging even after thousands of operating hours,

It exhibits exceptional corrosion resistance in chemical environments containing phosphoric acid, nitric acid, chlorides and sulfuric acid. It also has good mechanical properties at both ambient and elevated temperatures.

HT PIPE is specialized in supplying the very good quality of Inconel 601 flanges that are actually created using premium quality of raw materials.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

ASTM A193 Grade B8 Grade 1 Bolts and Studs Made of AISI 304 Stainless Steel. Type 304 is the most commonly used stainless steel grade in the fastener industry.

Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Material: Duplex Steel ASTM A789 S31803,S32205,S32750, S32760
ASTM A790 S31803,S32205,S32750, S32760

All SA234 WPB Elbow are manufactured in India and produced from strictly European sourced raw material.

Hastelloy B3 Flanges are also being offered in customized sizes, and shapes to our valuable clients.

AISI 904L stud bolts are manufactured to ASTM A182 F904L forged material. AISI 904L stud bolts are manufactured from ASTM A276/A276M and A479/A479M bar stock specifications. These stainless steel 904L stud bolts are constructed with dimensions referenced to various ASME/DIN/ISO/UNI/PN/BS and BIS standards. AISI 904L stud bolts are duly marked for traceability.

AMS 5754 pipe bend has no yield or tensile strength requirements, but it does require a hardness maximum and stress rupture minimums.

Type 304L is a variant of Type 304 with a low carbon content to improve weldability and reduce the risk of reduced corrosion resistance around the weld. The yield strength and tensile energy of Type 304L are also slightly reduced compared to Type 304.

B2 has significantly lower carbon, silicon and iron compared to its¡¯ predecessor, Alloy B (UNS N10001), making the alloy less susceptible to decreased corrosion resistance in the weld zone, in the as-welded condition.

Also known as alloy k500, Monel K500 fasteners and flanges are comprised of a nickel alloy that combines the outstanding corrosion resistance of Monel 400 with increased strength and hardness. Stronger than 400, alloy K500 even retains this strength in corrosive conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.