316l vs monel 400 tubo y tuberia

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

When utilized at subzero temperatures, these fasteners actually increase their tensile and yield strengths, while ductility and toughness are virtually unchanged. In addition, the flange face differs as flat face, raised face and ring type joint face as well. The Monel Slip On Flange is most useful with seamless pipes. The seamless pipes can easily slip onto the flange and reach the precise connection location. The ASTM B564 Monel 400 Lap Joint Flanges and other flanges can also come as threaded, forged, screwed or plate flange types.

It combines the corrosion resistance of Monel K-500 but gives the added advantage of extra strength and hardness (as a result of its age hardening ability).

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance to a wide range of media.

The chemical composition of Monel K500 Nippo Flanges provides great resistance to a lot of corrosive environments, such as pitting, crevice corrosion, inter ¨C granular corrosion, and stress ¨C corrosion cracking. Monel K500 Spacer Flanges has useful resistance to boiling sulfuric acid up to 40 % concentration, to 60 % concentration at 176 Degree F and in all concentrations to 150 Degree F.

Alloy 400 Pipe Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Monel K500 is a nickel-copper alloy that combines the excellent corrosion resistance of Monel 400 (link) with the added benefits of higher strength and hardness. Performance can be improved by adding aluminum and titanium to the nickel-copper matrix and by heating under controlled conditions to precipitate submicroscopic particles of Ni3 (Ti, Al) throughout the matrix. This is commonly referred to as age hardening or aging.

Monel 400 Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

The hex head design of the Monel bolt also allows the wrench to easily grasp it, improving the tightening and loosening experience. Monel k500 ASTM material provides advanced quality corrosion protection from hydrofluoric acid, salts, alkalinity and more. Monel NiCu k500 hex bolts are also resistant to seawater and steam, so they are a solid choice for marine applications.

Monel 400 is a popular high performance nickel copper alloy commonly used in critical and high performance applications. Monel 400? has high strength, excellent resistance to acid and alkaline environments, and good ductility and thermal conductivity. This alloy maintains its properties and performance in temperatures ranging from subzero to 1,000¡ãF (538¡ãC). Monel 400 can only be hardened by cold work.

Another important characteristic of Monel 400 Blind Flange is its resistance to halides or halogen containing solutions.

Monel K500(alloy K500), UNS N05500 (QQ-N-286), is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150¡ãF (-101¡ãC). This alloy shows the corrosion resistant characteristics of grades such as Alloy 400 but with enhanced strength and hardness after precipitation hardening. However, it can be further strengthened by cold working before the precipitation hardening.

The best machinability for these Monel K500 Lap Joint Flanges is in the annealed condition. Meanwhile, these Monel K500 Socket Weld Flanges are also being offered in different sizes and shapes to our customers.

Monel K500 pipe bend and elbow are resistant to a sour-gas environment

The increased properties are obtained by adding aluminum and titanimum to the nickel-copper base, and by heating under controlled conditions so that submicroscopic particles of Ni3 (Ti, Al) are precipitated thoughout the matrix.

Generally, the corrosion resistance of Monel K500 in solid solution is basically the same as that of Monel 400 alloy, so the corrosion resistance data of Monel 400 can be applied to Monel K500 alloy. Due to its low corrosion rate and high strength in flowing seawater, the alloy is particularly suitable for manufacturing seawater corrosion-resistant centrifugal pump shafts.

Monel 400 is resistant to a variety of corrosive conditions. For example, acidic applications involving hydrofluoric acid, brine, sulfuric acid and bases. Alloy 400 can only be hardened by cold work. Monel 400 is used in many industries for its excellent corrosion resistance, especially marine and chemical processing.

Typical applications for alloy K-500 pipe bend and elbow are pump shafts and impellers; doctor blades and scrapers; oil-well drill collars and instruments; electronic components; springs; and valve trim.

Monel nickel-copper alloy K-500 pipe bend and elbow combine the excellent corrosion resistance characteristic of Monel alloy 400 with the added advantages of greater strength and hardness.

ANSI B 16.47 Monel DIN 2.4375 Threaded Flanges are welded to a pipe or fitting with a single full penetration. ASTM B 564 Monel K500 Lap Joint Flanges may be used at all pressures and are available in a full- size range. They can be salvaged for use in systems that erode or corrode quickly. We keep a tab on market trends and demands, to invent new, sustainable and economical products capable of undergoing customization. Our products are fully certified and 100% durable.

Monel 400 Welded Pipe (NA13, N04400) offer hardness, strength and corrosion resistance with good fabrication capabilities. Monel 400 ERW Pipe can easily be welded by gas metal arc, gas-tungsten arc or shielded metal arc processes using appropriate filler metals.

It has excellent solderability and can withstand very high pressure and weight. The alloy has excellent mechanical properties at sub-zero temperatures, with a melting point of 2370¡ã – 2460¡ã F, and the product can be used at temperatures up to 1000¡ã C.

Monel K500 fasteners have trusted properties such as strength, hardness and fracture toughness, which are achieved through the addition of aluminum and titanium as well as nickel and copper alloys. Its basic composition is similar to ALLOY400, but alloys are added to allow age hardening under controlled temperature and time conditions.

Alloy 400 is highly regarded as one of the best performing engineering alloys.

Monel K500 pipe bend and elbow are usually used in propeller, pump shafts, pumps, valves used in the manufacture of perchlorethylene, and chlorinated plastics.

A nut is a threaded fastener that can be used with a bolt to secure a virtually unlimited number of parts, objects, and accessories for many types of applications. Monel 500 alloy provides short and long term benefits when used as a material for making nuts. Monel nickel copper k500 nuts provide strength and corrosion resistance in both acidic and alkaline environments. Monel nickel copper k500 nuts are also known for their favorable dimensional accuracy and non-corrosion in salt water and hydrofluoric acid.

Also known as alloy k500, Monel K500 fasteners and flanges are comprised of a nickel alloy that combines the outstanding corrosion resistance of Monel 400 with increased strength and hardness. Stronger than 400, alloy K500 even retains this strength in corrosive conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

MONEL K500 is a nickel-copper alloy, precipitation hardenable through additions of aluminum and titanium.

Monel K500 pipe bend and elbow are exceptionally good dimensional stability.

Si bien es un metal muy util, tiene un costo prohibitivo en la mayoria de las aplicaciones. Monel 400 cuesta de 5 a 10 veces mas que el niquel o el cobre normales.

The high pressure rating of Monel flanges means they can be used in high pressure environments.