4 inch nickel alloy 90 degree elbow pipe fitting Inconel 600 601 625 718

ASTM B366 N08825 Incoloy 825 fittings provide smooth operation at high temperatures. Our Incoloy 825 Elbow is used in a wide variety of industries due to its corrosion resistance properties in oxidizing and reducing environments.

Stainless steel 310 reducers are a mixture of several metals (this is called an alloy), but mostly iron, which is harder and stronger than iron. Stainless Steel 310S Cross Butt Weld Fittings are typically ferrous alloys with a carbon content between 0.02% and 1.7% by weight. Stainless steel 310 bend butt welded pipe fittings with carbon content above this value are called cast iron, in which the carbon is replaced by other alloy materials.

Carbon steel pipes are known for their ability to withstand high temperatures and are ideal for steam pipes. However, if you are trying to work in extreme climatic conditions (for example, transporting cryogenic liquids), you must use a different grade of pipe.

30 deg long radius 304 316 321 stainless steel pipe fittings weld S30400 elbow for incredible corrosion resistance in chemical environments containing phosphoric, nitric, sulphuric and chloride acids. However, it is significantly resistant to warm sulfuric acid. The increased power of the tube may also require better forming pressures.

HastelloyC-276 (Hastelloy) is a tungsten-nickel-chromium-molybdenum alloy with extremely low silicon-carbon content and is considered to be an all-around corrosion-resistant aluminum alloy. The key moisture-resistant chlorine, various air-oxidizing fluorides, isopropyl titanate solutions, hydrochloric acid and air-oxidizing salts, have good corrosion resistance in ultra-low temperature and standing temperature sulfuric acid. Therefore, in the past 30 years, it has been widely used in extremely corrosive natural environments such as chemical plants, petrochemicals, flue gas desulfurization, pulp and paper industry, and environmental protection.

Corrosion resistance

The aluminum alloy has the following characteristics: 1. It has good corrosion resistance to most corrosive substances under the two conditions of air oxidation and repair. ¢ÚIt has good resistance to pitting corrosion, void corrosion and intergranular corrosion. The higher content of Mo and Cr makes the aluminum alloy resistant to corrosion by chloride ion content, and the W element further improves the corrosion resistance. At the same time, Hastelloy C-276 aluminum alloy is one of the only types of raw materials that are resistant to wet chlorine, hypochlorite and chlorine dioxide saturated solutions. Ester solution has obvious corrosion resistance. It is one of the very few raw materials that can be used as a hot sulfuric acid saturated solution.

1.4529 German numeral code. Is a super duplex stainless steel, the main components: 20Cr-25Ni-6Mo-1Cu-0.2N corresponding to the United States: N08926, 254SMo…
1.4529 (UNS N08926) has very high resistance to pitting and crevice corrosion in halide media and in acidic environments containing sulfur and hydrogen
It can effectively resist chloride ion stress corrosion, and also has good corrosion resistance and good stability in oxidizing and reducing media.
The mechanical properties are slightly better than 904L, and it can be used in the manufacture of pressure vessels from -196 to 400 ¡ãC.

Inconel Tube Fittings can be easily elongated by 40% and still possess excellent workability. These fittings have a melting point of about 1413 degrees C and have a long service life. The Inconel 600 Buttweld Fittings can be produced by hot or cold rolling processes.

AL-6XNalloy (UNS N08367) is a low carbon, high purity, nitrogen-bearing “super-austenitic” stainless alloy. The AL-6XN alloy was designed to be a seawater resistant material and has since been demonstrated to be resistant to a broad range of very corrosive environments. The high strength and corrosion resistance of the AL6XN alloy make it a better choice than the conventional duplex stainless steels and a cost effective alternative to more expensive nickel-base alloys where excellent formability, weldability, strength and corrosion resistance are essential.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

When we call a steel tee ¡°equal tee¡±, means the branch diameter of this tee is same with the main pipe (Run pipe) diameter of this tee. When we see only one size of tee in its description, it means this tee is the equal tee. for example, 8¡å tee mean the tee main pipe and branch pipe both are 8 inches. Sometimes the equal tee also described 8¡åX8¡å which is the same meaning of 8¡å tee.

The 316L is a low carbon version, while the 316H type is a high carbon version of 316 stainless steel. Meanwhile, the 316Ti is a titanium stable version of the 316. Anti-sensitization is achieved in type 316Ti by adding titanium to stabilize the structure to prevent the precipitation of chromium carbide, which is the source of sensitization.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

This alloy provides improved resistance in highly corrosive environments with sulfur-containing media and chlorides. Stainless steel UNS S31700 pipe elbows are non-magnetic in the annealed condition. It can be easily welded and machined. Stainless steel 317 / 317L forged fittings can be hardened by cold work.

These fittings have earned the 3A symbol, which requires an annual assessment to make certain each product conforms in all respects to the published standard.

The deformation activation energy is low during superplastic deformation, and the process may be controlled by diffusion.

Our stainless steel 310S butt weld fittings are said to be the most commonly used and easiest to use, offering more forms and finishes than any other grade in the stainless steel range. Since it is the low carbon form of the alloy, these SS 310 butt welded pipe fittings are used to simplify production.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

We are also shareholders of carbon steel pipe fittings, such as carbon steel butt welding elbows, butt welding carbon steel crosses, butt welding carbon steel tees, butt welding carbon steel end caps, carbon steel butt welding short pipe ends, etc.

In most instances, these fitting have been shaped to fit a profile in order to perform that particular function.We manufacture wide range of ASTM A234 Seamless Fittings such as ASTM/ ASME SA 234 Reducer, Elbow etc. AS per Universal standard like ASME/ASTM, we are supplying A234 WPB Carbon Steel Fittings globally.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Grade 2205 is the most widely used duplex stainless steel grade. Fittings of this grade finds applications due to both their excellent corrosion resistance as well as their high strength.

Stainless steel 316l pipe fittings are of a low carbon austenitic grade. The versatile pipe fittings are designed with a superior content of chromium, nickel, and small amounts of molybdenum.

This nickel steel alloy can be used in the as-welded condition because it resists the formation of grain-boundary carbide precipitates in the weld heat-affected zone.

304 and 304L are austenitic alloys, which means that a nonmagnetic solid solution of ferric carbide or carbon in iron is used in giving this stainless steel its corrosion-resistant properties.

Commercial applications involve furnace components and fixtures requiring strength and oxidation resistance at temperatures up to 2000 degrees F.

Duplex stainless steel 2205 tee consists of branch pipe diameters, which are also tee pipes. These tees have 3 internal holes and can connect pipes of different diameters. Duplex Ss 2205 Reducers are used to accommodate pipes of different sizes in piping systems. These reducers can be concentric or eccentric.

316 Stainless Steel Pipe Fitting is widely used in the connection of pipe fittings. Our company has been manufacturing and supplying stainlesss steel elbow for years of experience. With the advantages of huge stock ability, we could provide you the quick delivery. Besides, with a strict quality control system, we could guarantee the quality.