4 inch steel pipe fittings 304 tee of tube connector tee connector pipe

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

C22 has excellent resistance to oxidation, carburization, and sulfidation at elevated temperatures. However, C22 should not be used at temperatures above 1250¡ãF due to the possible formation of embrittling phases.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

The carbon steel seamless pipe fittings, buttwelded fitting and fabricated ones are available in the market.

Stainless Steel 304 Buttweld Fittings are made up of a basic austenitic stainless steel material that has 18% chromium and 8% nickel in its composition.

The ASTM A234 WP5 specification consists of wrought carbon steel and alloy steel in seamless and welded form. The ASTM A234 WP5 Pipe Fittings are widely used in pressure vessel fabrication. These fittings have application under moderate to high temperatures and can also be effectively used in pressure piping systems.

Stainless Steel 304 Pipe Fittings are made from seamless steel pipes whereas ERW pipes are made from ERW steel pipes.

304 fittings meet steel 304 strength standards and 304L ultra-low carbon standards. Fittings are components used in many different industries to connect, terminate, control flow and change the direction of pipes.

It has high quality and erosion resistance.?317 Stainless Steel Elbow?is harder than?SS ASTM A403 WP317 Buttweld Fittings. It is suggested to utilize chip breakers.?

A234 WP9 carbon steel pipe fittings are widely used in many different industries. Alloy Steel A234 Gr. WP9 Buttweld Pipe Fittings are a type of pipe fitting made from carbon steel material, which is strong, durable, and resistant to corrosion. These Alloy Steel WP9 Butt weld Pipe Fittings are commonly used for connecting pipes and fixing them into place. ASTM A234 WP9 Pipe Fittings can be used for both small and large-scale projects, making them incredibly versatile and useful.

Sanitary pipe fittings AISI304, AISI304L, AISI316, AISI316L, its standard is DIN/SMS/3A/ISO/IDF, pipeline flow control: DN10-DN200&1 /4″”-8″, it is used in stainless steel pipe system, its working principle It can be welded on the pipeline to adjust the flow in the pipeline. Its medium includes beer, dairy products, beverages and pharmaceuticals.

ASTM A403 WP 310 Butt Weld Elbow is a pipe fitting commonly used to turn pipes in different directions at either a 45 degree or 90 degree angle. There are also different sized elbows. They are short radius elbows or long radius elbows. Grade 310 steel has a minimum yield strength of 205MPa and a minimum tensile strength of 515MPa. Due to the high melting point, 310 stainless steel butt welded pipe fittings can also work at high temperatures. The 310 material has a melting point of 1402 degrees Celsius. This allows fittings for high pressure and high temperature services such as heat exchangers and boiler components.

HASTELLOY X is a wrought nickel-based alloy with excellent high temperature strength and oxidation resistance. All product forms are excellent in forming and welding. Although HASTELLOY X is primarily known for its heat and oxidation resistance, it also has good resistance to chloride stress corrosion cracking and good carburization, as well as excellent resistance to reducing or carburizing atmospheres. Alloy X is one of the most widely used nickel-based superalloys for gas turbine engine components.

All ASTM A234 Elbow & Elbow A234 Wpc are manufactured from plate, pressed in two halves with two weld seams. We offer 100% radiography on all welds as standard.

Forging fittings Carbon content 0.35% maximum and Silicon content 0.35% maximum, no minimum.

ASME B16.9 SS Pipe Fittings that have matching pipe schedules offer seamless flow inside the pipe. A properly fitted elbow helps in gradual transition via pipes which can be terminated using a Stainless Steel pipe cap. Most of the buttwelds are beveled ended. This helps in creating full penetration without the need for extra penetration for ASME B16.9 SS Pipe Fittings.

316L elbow is tested well on various quality parameters. Stainless Steel 316L Socketweld Pipe Elbows are durable and are highly resistant to corrosion.

Titanium rapidly starts to react with oxygen molecules at around 1,200 ?C, and it can exhibit the same behavior at a reduced temperature of 610 ?C when the oxygen is in pure form.

Stainless steel tee used a lot in chemical, sanitary or food industries.It¡¯s advantage is suitable for different working environments and good corrosion resistance.

Astm b366 incoloy 800ht butt welded pipe fittings have some chemical compositions such as chromium, nickel and iron. Our butt welded pipe fittings provide increased creep and stress rupture and high temperature corrosion resistance. These butt weld fittings are available in custom and standard forms. Astm b366 incoloy 800ht butt welding fittings manufacturing process to ensure top quality.

Inconel Tube Fittings can be easily elongated by 40% and still possess excellent workability. These fittings have a melting point of about 1413 degrees C and have a long service life. The Inconel 600 Buttweld Fittings can be produced by hot or cold rolling processes.

It exhibits excellent weldability and can withstand very large amounts of pressure and weight.

Grade 316 pipe bend also has given excellent service in potable water. Pitting and crevice corrosion may occur in waters with higher chloride content, and 2000 ppm is accepted as the upper limit. The higher molybdenum content of 316 make it significantly more corrosion resistant than grade 304.

Hastelloy C-276 has a higher molybdenum content.

Duplex stainless steels are a family of stainless steels. These are called duplex (or austenitic-ferritic) grades because their metallurgical structure consists of two phases, austenite (face-centered cubic lattice) and ferrite (body centered cubic lattice) in roughly equal proportions. They are designed to provide better corrosion resistance, particularly chloride stress corrosion and chloride pitting corrosion, and higher strength than standard austenitic stainless steels such as Type 304 or 316.

These A234 WPB SCH 80 Elbow are also available in a wide size range. The purpose to use a ASTM A234 gr WPB elbow is to change direction or flow in a piping system.

Type 304 stainless steel is a T 300 Series Stainless Steel austenitic. It has a minimum of 18% chromium and 8% nickel, combined with a maximum of 0.08% carbon. It is defined as a Chromium-Nickel austenitic alloy.304 stainless steel is used for a variety of household and industrial applications such as food handling and processing equipment, screws,[3] machinery parts, utensils, and exhaust manifolds. 304 stainless steel is also used in the architectural field for exterior accents such as water and fire features. It is also a common coil material for vaporizers.

Stainless steel tees, carbon steel tees and special grade tees are widely supplied by us to many industries such as power generation, petrochemical, shipbuilding, paper manufacturing, chemical, pharmaceutical, and fabrication.

The most common dimensional standard for 45 degree carbon steel is SME B16.9, B16.28 MSS-SP43/75 for sizes ranging from ?¡± to 72¡å (in all Schedules).