52in. forged A182 F5 alloy flange for bop

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nuts with a nominal size over 1 inch shall be a UNC Series Class 2B fit or an 8 UN Series Class 2B fit. High strength ASTM A194 grade 2H nuts are common in the market and are often replaced by ASTM A563 grade DH nuts due to the limited availability of DH nuts in certain diameters and finishes.

High alloy steel is defined by a high percentage of alloying elements.

Bolts and bolts are used in many applications in almost all industrial applications.

ASTM A320 L7M Grade AS Fasteners are commonly used in oil and gas exploration and processing equipment – piping, piping and heat exchangers.

HastelloyC-276 (Hastelloy) is a tungsten-nickel-chromium-molybdenum alloy with extremely low silicon-carbon content and is considered to be an all-around corrosion-resistant aluminum alloy. The key moisture-resistant chlorine, various air-oxidizing fluorides, isopropyl titanate solutions, hydrochloric acid and air-oxidizing salts, have good corrosion resistance in ultra-low temperature and standing temperature sulfuric acid. Therefore, in the past 30 years, it has been widely used in extremely corrosive natural environments such as chemical plants, petrochemicals, flue gas desulfurization, pulp and paper industry, and environmental protection.

Corrosion resistance

The aluminum alloy has the following characteristics: 1. It has good corrosion resistance to most corrosive substances under the two conditions of air oxidation and repair. ¢ÚIt has good resistance to pitting corrosion, void corrosion and intergranular corrosion. The higher content of Mo and Cr makes the aluminum alloy resistant to corrosion by chloride ion content, and the W element further improves the corrosion resistance. At the same time, Hastelloy C-276 aluminum alloy is one of the only types of raw materials that are resistant to wet chlorine, hypochlorite and chlorine dioxide saturated solutions. Ester solution has obvious corrosion resistance. It is one of the very few raw materials that can be used as a hot sulfuric acid saturated solution.

Users of SA182 Chrome Moly Gr.f9 forged bar do not rely solely on external coatings or finishes.

The flange connection type usually comes with double units, with a gasket and some bolts & nuts to connect each other. (Firstly pipes are welded on the flanges, then valves and other equipment could be installed on flanges.)

We are a manufacturer, trader, stocker, supplier and exporter of B7-2H Fasteners.

The A335 Chromium (or Chromium) is the basic component of stainless steel. Any steel with 12% or more chromium is considered stainless steel. Chromium is almost irreplaceable in terms of resistance to oxidation at high temperatures. Chromium increases tensile, yield and hardness at room temperature.

ASME SA 335 / ASTM A335 P91 pipe has some great features like fully tested, cost effective, quality certified and more. The ASTM A335 Alloy Steel P91 Pipe offered is manufactured by our experts utilizing the highest quality stainless steel and advanced technology.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.49

The Alloy Steel Weld Neck Flange has a welded neck onto it that holds larger pipes in place for easy welding and installation.

These pipes are highly resistant to high temperature and corrosive environments. The absolute roughness of astm a335 gr P9 seamless pipe is small, so the size is very accurate.

Alloy 20 (Alloy 20) is an iron-based austenitic alloy developed to resist sulfuric acid corrosion. It has excellent resistance to sulfuric acid corrosion; it has strong resistance to phosphoric acid, nitric acid and chloride environments, chloride stress corrosion, pitting corrosion and crack corrosion. Therefore, alloy 20 has the name of anti-corrosion alloy; it has a wide range of applications: such as: chemical, food, medicine, power production and plastics industries will use it. For resistance to pitting corrosion and chloride corrosion, stress corrosion cracking problems, etc., alloy 20 is often used.

The material can be heat treated to anneal and normalize in air, or quench and temper in polymer or oil. Alloy 4130 has a lower carbon content of 0.28% – 0.33% and slightly higher amounts of other elements. And the material is easy to process. 4140 low alloy steel has a range of 2. 375″ to 12.750″ OD with wall thicknesses ranging from 0.375″ to 1.5″. Alloy 4145 has a slightly higher carbon content than 4140 and 4130 types of pipes.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P139

ASTM A335 seamless steel pipe is commonly referred to as chrome molybdenum pipe with chemical elements molybdenum and chromium. Molybdenum can improve steel properties such as strength, elastic limit, wear resistance, impact resistance and hardenability.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P93

ASTM A182 F5 Lap Joint Flanges go by a range of names, including back up flange, loose hubbed flange, loose ring flange and van stone flange. ASTM A182 F5 Flanges is a method of connecting pipes, valves, pumps and other equipment to form a piping system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or screwed. Flanged joints are made by bolting together two flanges with a gasket between them to provide a seal.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

The corrosion resistance of SA 335 P91 seamless pipe is much higher than that of carbon steel. Grade P91 is a reference for the chemical composition of alloy steels. A chromium-molybdenum steel, the chemical composition of ASTM A335 P91 alloy steel pipe consists of 9% chromium and 1% molybdenum and vanadium.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.22

The a182 f9 material contains a certain amount of chromium and molybdenum, both of which contribute to a longer service life and therefore longer life.

These are said to be specifications for alloy flanges for high pressure and service. The 3% carbon content of these flanges provides a lot of room for improved weldability, which also increases their overall strength.

ASTM A320 Grade L7M bolts and studs are also made from quenched and tempered alloy steel.

Which means that one has to know if the alloy steel flange material is critical to achieving good weld integrity and the need for proper filler metal selection.High heat resistance steel grades are generally known as Chromium Molybdenum Steel.

A low alloy steel flanges series mostly consists of approximately 0.5% to 9% of Chromium. And the content of Molybdenum in the alloy steel flanges ranges anywhere between 0.5% to 1% .

One of the top stocks of ASTM A182 alloy steel F5 flanges for a variety of industrial applications. With a talented team of professionals, we are committed to supplying the highest quality ASTM A182 Alloy Steel F5 Flanges, widely used by customers in suitable applications.

ASTM A335 P9 pipe standards and schedules vary based on the needs of the application. A335 P9 chromium pipe composition contains 9% chromium and 1% molybdenum.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.55

There are other different types of ASME SA 182 AS Pipe Flanges such as the weld neck flanges and socket weld flanges each specified for a particular role.

The A335 P91 chrome tube composition makes these high mechanical properties possible for the material. P91 steel pipe materials can be normalized and tempered during the production process, and can also be quenched and tempered. These methods increase the strength of the material. Additionally, these pipes are drawn and seamless.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.24

A333 P92 steel is American steel grade ASTM A335 P92, which is a martensitic heat-resistant steel. In recent years, it has been widely used in thermal power plants, mainly for main steam pipelines and reheat steam pipelines. The main alloy components are Cr: 9%, Mo: 1%, etc.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.59

Alloy pipe is a higher percentage of tubular alloying elements such as molybdenum (Mo), chromium (Cr), nickel, etc. than standard carbon steel pipe. In fact, ASTM A335 covers “low alloy” steel pipes, that is, having less than 5% total alloying elements. The addition of higher percentages of alloying elements such as nickel and chromium converts the steel into higher alloys such as stainless steel, duplex stainless steel, up to superalloyed materials such as Inconel, Hastelloy, Monel, etc.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P100

We are also a supplier and exporter of Alloy Steel ASTM A182 F5 Butt Weld Flanges for high pressure hydraulic systems.