6 inch elbow nickel alloy pipe fitting elbow nickel alloy

Inconel 601 (UNS N06601 ) nickel-based alloy density: 8.42 g/cm3 (grams/cubic centimeter).

Grade 1.4404 or 316L is an austenitic stainless steel AISI 316 with very good corrosion resistance due to its high chromium and molybdenum content and low carbon content. Its strength in the hardened state is about 600 MPa for large diameters, but for small sections, the strength can be increased by cold working.

Nickel Alloy 600 works well with most alkaline solutions and sulfur compounds and also provides lower rate of attack from chlorine or hydrogen chloride.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

Grade 430 is a ferritic, straight chromium, non-hardenable grade, combining good corrosion resistance and formability characteristics with useful mechanical properties. Its ability to resist nitric acid attack permits its use in specific chemical applications but automotive trim and appliance components represents its largest fields of application.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

The principle di?erence between alloys 800H and 800HT is the restricted aluminum and titanium content in 800HT, which results in higher creep and stress rupture properties.

The 304 elbow is a stainless steel threaded pipe fitting that changes the direction of the pipeline in the pipeline system. According to the angle, there are 45 ¡ã and 90 ¡ã. In addition, according to engineering needs, it also includes other abnormal angles such as 60 ¡ã. The material of our threaded elbows is 304 stainless steel.

HT PIPE offers a range of precision finished duplex fittings & flanges to ensure a good flow in seamless. Our flanges are corrosion resistant & designed to operate in high pressure environments. Here at HT PIPE we supply a broad range of piping products and materials which are used in many different industries.

Our high quality stub end A-type stub end butt welded joints are tested and proven for durability, accuracy and precision. ANSI B 16.9 Stub End is widely used in plumbing engineering to connect different types of pipes.

This concentric reducer has a high conductance tapered profile that reduces tube size. Butt weld joints are fabricated from welded, drawn and annealed 304 stainless steel tubing for applications where the number of sealed joints needs to be minimized.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Both materials remain available, subject to commercial considerations, and certain specifications which restrict the service temperature of some grades of INCOLOY alloy 800H.

This 316L Stainless Steel 90 Degree Weld Elbow is a common connection pipe fitting used in plumbing installation. It is used for connecting the bend of pipe and changing the direction of pipe. Since the 90 degree weld elbow has good strength and resistance to corrosion, it has long service life and low maintenance cost.

Monel K500 pipe bend and elbow are virtually nonmagnetic, even at quite low temperatures

This combination makes the material resistant to corrosion and high temperatures up to 889 degrees Celsius. 304 stainless steel butt weld fittings meet standard ASTM A403 and are available in outside diameters from ?” to 48″. For seamless fittings, diameters range from ? to 10 inches.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

The Stainless Steel 304 Fittings one of the most commonly used types of pipe fittings all over the world.

In this standard it covers the specification of elbows, tees, reducers, caps and cross, it usually adopt butt welding ends.

Hastelloy X pipe bend is corrosion resistant, heat resistant and oxidation resistant, being able to withstand reducing or neutral atmospheres and oxidation.

We supply and sell 304/316L Sanitary Stainless Steel Pipe Fitting Reducing Tee with reasonable price and reliable quality to create a sincere enterprise. Now, we are trying to enter new markets where we do not have a presence and developing the markets we have the already penetrated. In line with the principle of customer first, we constantly pursue perfection, improve the technical content and quality of products, and constantly improve ourselves while meeting customers.

They primarily provide resistance to chloride stress corrosion and chloride pitting corrosion. They have higher chromium and molybdenum content than other austenitic stainless steels.

It is commonly referred to by the tradename Hastelloy C22 and the universal designation UNS N06022. C22 has excellent corrosion and oxidation resistance, great mechanical properties over a wide range of temperatures, and good fabrication properties.

In the annealed condition, stainless steel 317L fittings are non-magnetic. Although fittings manufactured from Grade 317L cannot be hardened by heat treatment, the material will harden by cold working. 317L fittings can be easily welded and machined by traditional shop fabrication methods. No post weld heat treatment is required for these fittings. Generally, grade 317 stainless steel can be welded using fusion welding and resistance welding methods, but for these 317L stainless steel fittings, oxyacetylene welding is not the preferred method. For best results, use 317L filler metal or AWS E/ER317 or .

We are a manufacturer, supplier and exporter of Alloy Steel ASTM A234 WP22 Buttweld Fittings that form meaningful connections between multiple pipes of various sizes.

SS 316 elbows are used to change the direction of pipes. They are available in different shapes, sizes and dimensions. The carbon content of these pipes is lower than 301 and 304 grades. Therefore, 316 stainless steel welded pipe fittings are said to be a suitable choice for welding.

The chromium and nickel contents of this alloy provide excellent oxidation resistance at low concentrations of oxidizing and reducing sulfur, good resistance to carburization and sulfidation. The alloy also has reasonable resistance to nitriding in cracked ammonia, but not as much as Inconel 600.

ASTM A420 WPL6 Pipe Fittings are made up of a carbon steel alloy that is made up of carbon, manganese, phosphorus, sulfur and silicon.