80mm x three-eighth bsp female 304 stainless steel pipe fitting pagoda joint ASTM A815 UNS S32750 EQUAL TEE

ASTM A420 WPL6 Pipe Fittings are one kind of butt welding pipe fittings,they are commonly produced from the steel pipes of ASTM A333 Grade 6.

In fact, the above properties of 317L fittings are considered to be much better than traditionally used stainless grades such as 304, 304L, 316 and 316L. The alloys used for stainless steel 317L are known to provide better resistance than 316L, especially in highly corrosive environments, which may contain chemicals such as sulfur-containing media, chlorides and other halides.

Copper Nickel Fittings are also known as Curpo Nickel Fittings (Cu-Ni Fittings), Copper Nickel C71500 (70/30) and UNS C70600 (90/10) Fittings. Simplex offers a full line of copper pipe fittings such as copper-nickel UNS C71500 elbows, copper-nickel (Cu-Ni) 70/30 reducers, copper-nickel tees, copper-nickel stub ends, copper-nickel elbows and copper-nickel crosses .

This combination makes the material resistant to corrosion and high temperatures up to 889 degrees Celsius. 304 stainless steel butt weld fittings meet standard ASTM A403 and are available in outside diameters from ?” to 48″. For seamless fittings, diameters range from ? to 10 inches.

Inconel 625 Pipe Fittings are strong and are used in high corrosive applications that need stronger pipes. The material is a nickel chromium molybdenum alloy with niobium in the composition for stabilization. It can operate from cryogenic temperatures up to 1093 degrees Celsius. So the fittings are preferable for applications that require high strength, corrosion resistance and high temperature resistance. The Alloy 625 Buttweld Fittings are used with ease of welding and this is the most used type of fittings. The Inconel UNS N06625 Pipe Elbow is used to turn the pipe away by an angle, usually 45 degrees or 90 degrees. The ANSI B16.9 ASTM B366 625 Inconel Monel Tee can range from ? inches to 48 inches in nominal bore size and it branches a pipe into two.

Incoloy 800H and 800HT are typically used in parts above 1100¡ãF where creep and fracture resistance is required. The chemical balance allows nickel steel alloys to exhibit excellent resistance to carburizing, oxidizing and nitriding atmospheres. Incoloy 800HT will not become brittle even after prolonged use in the 1200-1600¡ã F range where many stainless steels become brittle. 800HT exhibits the excellent cold forming qualities normally associated with Nichrome.

The high chromium content provides good resistance to oxidizing media while the molybdenum and tungsten content give good resistance to reducing media.

The Carbon Steel A234 WPB Smls Reducer is a seamless product that reduces the diameter of the pipeline.Unless specified for carbon steel plates or sheet, the steel may be made to either coarse grain or fine grain practice. Which ASTM A234 WP9 shall be made to fine grain practice.

Stainless Steel Pipe Bends is used in the textile and printing industry due to its versatility and weldability.

Duplex steel tees generally perform well in environments that cause premature failure of austenitic grades, where it has better seawater resistance than 316 grades. Duplex steel is a nitrogen-enhanced stainless steel designed to solve common corrosion problems encountered with 300 series stainless steels.

The difference between 304 and 304L stainless steel is that 304L has a .03 max carbon and is good for welding whereas 304 has a mid range level of carbon.

ASTM B366 UNS N08800 N06625 N08020 N04400 N06600 N08904 N08031 180deg ELBOW ASME B16.9 features corrosion resistance, accurate dimensions, withstands high pressure and high temperature loads, rust-resistant finish, smooth transition from flange thickness to pipe and ensures excellent stress distribution.

Incoloy 800HT is a nickel-iron-chromium alloy, and also a modified version of alloy 800.

ASTM A815 Pipe Fittings, ASTM A815 Super Duplex 2507 Pipe Fittings, UNS S32750 Super Duplex Pipe Fittings, ASTM A815 32205 Seamless Pipe Fittings, ASTM A815 S32950 Butt weld Fittings, ASTM A815 Super Duplex S32760 Pipe Fittings Exporter.

Stainless Steel UNS N08904 Seamless Pipe Fittings, ASTM B366 904L Stainless Steel 90 degree Elbow Exporters, 904L Stainless Steel Reducer, Stainless Steel 10d Pipe Bend, SS 904L Short Radius Elbow Supplier.

It is more resistant to general corrosion and pitting than conventional nickel chromium stainless steels such as 302-304.

Our ASTM A403 SS 304 Elbow has a tensile strength of 75 ksi, guarantees extreme dexterity, has a load-carrying capacity high enough to work under constant pressure, is resistant to atmospheric corrosion, and can be used to seal pipe ends and prevent General-purpose fluids such as internal contamination.

Duplex 2507 is a super duplex stainless steel designed for applications which demand exceptional strength and corrosion resistance. Alloy 2507 has 25% chromium, 4% molybdenum, and 7% nickel. This high molybdenum, chromium and nitrogen content results in excellent resistance to chloride pitting and crevice corrosion attack and the duplex structure provides 2507 with exceptional resistance to chloride stress corrosion cracking.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Duplex steel pipe fittings are the profession of repairing or installing pipes or piping systems that carry liquids, gases and occasionally solid materials. It is a ferritic-austenitic microstructure with a phase balance of approximately 50% ferrite and 50% austenite.

All of the common methods of welding can be used to weld Hastelloy C-276 alloy, although the oxyacetylene process is not recommended. Special precautions should be taken to avoid excessive heat input.

WPHY 52 Pipe fittings are manufactured as per MSS SP 75 shall be furnished in the heat treated condition.We offer a wide assortment of ASTM A860 WPHY 52 Fittings that cater to the prerequisite of different industries such as engineering, chemical, refineries, machine apparatuses, and numerous others.

1.4529 German numeral code. Is a super duplex stainless steel, the main components: 20Cr-25Ni-6Mo-1Cu-0.2N corresponding to the United States: N08926, 254SMo…
1.4529 (UNS N08926) has very high resistance to pitting and crevice corrosion in halide media and in acidic environments containing sulfur and hydrogen
It can effectively resist chloride ion stress corrosion, and also has good corrosion resistance and good stability in oxidizing and reducing media.
The mechanical properties are slightly better than 904L, and it can be used in the manufacture of pressure vessels from -196 to 400 ¡ãC.

We also produce Carbon Steel ASTM A234 WPB Threaded elbows with all male connections, all female or a combination of each.

The 2.4858 Long Stub End uses modern technology to provide these fittings with the perfect thickness, high strength and standard length. If desired, we can also customize these ASTM B366 Incoloy N08825 end caps to the end user in the application. They can withstand high pressures when transferring liquids.

It exhibits excellent weldability and can withstand very large amounts of pressure and weight.

ASTM B366 pipe fitting is used to connect straight pipe sections, adapt to different sizes or shapes and for other purposes, such as regulating(or measuing) fluid flow. These fittings are maded as per application requirements in different outer diameter and inner diameter with specified surface. HT pipe is a global distributor of nickel alloy pipe fittings in different sizes. Our company is constantly executing regualr as well as customised order for pipe fittings for sectors like oil and gas, engineering, etc.

These fittings material consist of killed steel, forgings, bars, plates, seamless or HFW (fusion welded) pipe products, with filler metal added.A234 WPB pipe fittings are butt welding ends,commonly used to be welded with the steel pipes of A106,A53,GR.B material,or API 5L GR.B material.

Pipe Tee is a type of pipe fitting which is T-shaped having two outlets, at 90¡ã to the connection to the main line. It is a short piece of pipe with a lateral outlet. Pipe Tee is used to connect pipelines with a pipe at a right angle with the line. Pipe Tees are widely used as pipe fittings.

304 has good oxidation resistance in intermittent duty up to 870¡ãC and continuous duty up to 925¡ãC. However, continuous use at 425-860¡ãC is not recommended. In this case, 304L is recommended because of its resistance to carbide precipitation.