90 degree butt weld seamless carbon steel elbow incoloy 800

Large selection of finished and semi-finished stainless steel caps/end caps, crosses, elbows, reducers, tees, stub ends and many other stainless steel butt weld fittings for use in power plants, oil and gas, water treatment, food processing , petrochemical, LNG industry, automotive, heavy engineering, offshore and chemical. We can supply butt welded pipe fittings individually or in conjunction with our other plumbing products.

The material has good strength with 240MPa minimum yield strength and 585MPa minimum tensile strength.

304 fittings meet steel 304 strength standards and 304L ultra-low carbon standards. Fittings are components used in many different industries to connect, terminate, control flow and change the direction of pipes.

ASTM A234 includes wrought carbon steel and alloy steel fittings of seamless and welded construction covered by the latest revision of ASTM B16.9, B16.11, MSS-SP-79, MSS-SP-83, MSS-SP-95, and MSS-SP-97. etc.

ASTM A420 WPL6 Pipe Fittings such as WPL6 Caps, A420 WPL6 Weld Fittings, and SA 420 WPL6 Elbow. Our stock of low temperature steel fittings includes A420 Grade WPL6 fittings in a complete range of sizes and thicknesses.

Stainless steel 310S differs from wrought iron, which contains little or no carbon, which also has variations and combinations of production routes. Stainless Steel 310 End Cap Butt Weld Fitting is an iron and carbon alloy containing less than 2% carbon and 1% manganese and small amounts of silicon, phosphorus, sulfur and oxygen.

Meanwhile, these Duplex Steel S32205 Cross Pipe Fittings are also available to our customers in different sizes and shapes. Duplex steel S31803 bent butt welded pipe fittings generally perform well in environments that cause premature failure of austenitic grades. Although duplex steel S32205 short end butt welded pipe fittings have good high temperature oxidation resistance, this grade – like other duplex stainless steels – can experience embrittlement if held at temperatures above 300 degrees Celsius for even short periods of time. If embrittled, duplex S31803 end caps can only be corrected by full solution annealing. Duplex S32205 Disc Lid Fittings are almost never used above 300 degrees Celsius.

For the seamless steel pipe fittings refers to the fittings raw material from the seamless steel pipes and tubes. Thus the welded steel pipe fittings covers the fittings raw material from welded steel pipes.

Alloy 600 / Inconel 600 is combination of Nickel Chromium and Iron providing a standard material for the chemical industry and the automotive engine, aero engine and airframe sectors.

Nickel alloy 20 is a low-carbon, niobium-stabilized austenitic nickel/iron/chromium alloy with additions of molybdenum and copper. ASTM B366 specification covers Inconel, Monel, Hastelloy and Nickel Alloy Pipe Fittings used in acidic and sea water.

We also offer Super Duplex S32760 Butt Weld Fittings and Super Duplex S32750 Fittings according to customer specific requirements. We also offer various shapes such as Super Duplex S32760 Stub Ends, Super Duplex S32750 Coupling Reducers, Super Duplex S32760 Elbows, Super Duplex S32750 Tube End Caps, S32760 Super Duplex Three links, etc.

Reducing tee, generally a professional term, tee for pipe fittings, pipe connectors, used in the main pipe to branch pipe.Reducing tee is a kind of tee, the tee has two kinds: general equal diameter tee and reducing tee.Named because the three ends can be connected to the pipe.

SS 304 Concentric Reducer also exhibits excellent ductility, spinning, forming and drawing properties.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

A234 WPB Elbow is produced and supplied in the butt welded form. SA234 WPB Elbow usually comes in either of three angles; 22.5, 45 or 90 degrees.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

30 deg long radius 304 316 321 stainless steel pipe fittings weld S30400 elbow for incredible corrosion resistance in chemical environments containing phosphoric, nitric, sulphuric and chloride acids. However, it is significantly resistant to warm sulfuric acid. The increased power of the tube may also require better forming pressures.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

316L elbow minimises harmful carbide precipitation due to welding.

Stainless steel tee is also a kind of pipe fittings, generally there are two kinds. That is, an equal tee, the diameter of the three ends is the same; a reducing tee, the diameter of the branch pipe is different from the other two.

Copper-nickel or copper-nickel elbows are moderately strong and commonly found in marine saltwater applications.

The combined effects of mechanical and thermal processing of Incoloy Alloy 800HT permit higher design stresses to be incorporated than are permitted for the conventional Alloy 800H.

UNS N06601 elbow has good heat resistance and high plasticity. The alloy can be strengthened by cold working, and can also be connected by resistance welding, soldering, or brazing. It is suitable for making oxidation resistance no low load below 1100C.

ASTM A815 specification covers two general classes, WP and CR, of wrought ferritic, ferritic/austenitic, and martensitic stainless steel fittings of seamless and welded construction. Class WP fittings are subdivided into four subclasses: Classes WP-S, WP-W, WP-WX, and WP-WU. The material for fittings shall consist of forgings, bars, plates, or seamless or welded tubular products.

A welded ASTM A403 Stainless Steel Weld Fittings is made up of pieces of steel plates. Stainless Pipe Fittings are made up of 10% nickel and high chromium content.

ASME SA 240 UNS S32205 elbows are standard elbows that can be connected to almost any size elbow. These elbows are available in NPS ? to NPS 48 and can change the direction of flow in the pipe. UNS S32205 elbows are stronger than austenitic stainless steels.

Sustained or prolonged exposure of Type 316L to 800-1500¡ãF (427-816¡ãC) may be harmful. In addition, stress relief between 100-1500¡ãF (593-816¡ãC) may cause this Type of slight embrittlement.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

316 stainless steel pipe is the second most common stainless steel after 304. SS DIN 1.4401 / 1.4436 Rectangular Welded Pipe, ASTM A312 TP316 Pipe, 316 Rectangular Pipe, 316 Pipe typically contain 16% Chromium and 10% Nickel with added Molybdenum typically between 2-3%.