90 degree bw pipe fitting duplex elbows

Titanium is also a ductile metal, especially in an oxygen-free environment.

Designed to combine impact toughness against chloride stress corrosion cracking with pitting and crevice corrosion, S31254 stainless steel is twice as strong as stainless steel 300 series.
It is also known for its excellent machinability.

For equal tee/straight tee, the center-to-end dimension of branch is same with the run, while for reducing tee, the center-to-end dimension of branch is smaller than the run to obtain the desired flow and pressure through the piping system.

This alloy provides improved resistance in highly corrosive environments with sulfur-containing media and chlorides. Stainless steel UNS S31700 pipe elbows are non-magnetic in the annealed condition. It can be easily welded and machined. Stainless steel 317 / 317L forged fittings can be hardened by cold work.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

It is used in flue gas desulfurizations systems because of its excellent resistance to sulfur compounds and chloride ions encountered in most scrubbers. C-276 alloy has excellent resistance to pitting and to stress- corrosion cracking.

While there are slight variances to different hot pipe bending methods, nearly all are a form of induction bending.

Grade 430 is a ferritic, straight chromium, non-hardenable grade, combining good corrosion resistance and formability characteristics with useful mechanical properties. Its ability to resist nitric acid attack permits its use in specific chemical applications but automotive trim and appliance components represents its largest fields of application.

Duplex Steel S31803 Front Ferrule Fittings are used in commercial and aerospace applications and can be freely formed and have best-in-class weldability. Given that the dual-phase steel S32205 rear ferrule joint is only about one-third the weight of comparable steel parts, it is the clear choice when weight is an aspect.

The alloy also has excellent mechanical properties and presents the desirable combination of high strength and good workability.

UNS S31254 is an alloy material with anti-corrosion effect, its density is 8.0g/cm3, and the melting point is 1320-1390¡æ. High molybdenum content and high chromium and nitrogen content make UNSS31254 extremely good resistance to pitting and crevice corrosion. The addition of copper improves corrosion resistance in certain acids. In addition, UNSS31254 has good resistance to stress corrosion cracking due to its high nickel content and high chromium and molybdenum content.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

We also accept all orders of CS Elbow A234 WPB up to and including 90 degree to suit your requirements.

Generally, the corrosion resistance of Monel K500 in solid solution is basically the same as that of Monel 400 alloy, so the corrosion resistance data of Monel 400 can be applied to Monel K500 alloy. Due to its low corrosion rate and high strength in flowing seawater, the alloy is particularly suitable for manufacturing seawater corrosion-resistant centrifugal pump shafts.

Duplex Stub End Fittings¡ªDuplex steel stub ends are installed in pairs and mate with two lap flanges. The surface of the alloy stub end has a voice pattern serrated gasket surface to prevent leakage at the joint. Use stub ends to open up parts of the circuit for cleaning, inspection, or quick replacement, etc., without the need for re-soldering.

AL-6XN is a low carbon, nitrogen containing super austenitic stainless steel. The alloy is designed to be a seawater resistant material and has been found to resist a wide range of corrosive environments. Due to the alloy’s corrosion resistance and high strength, AL-6XN is a better choice than traditional duplex stainless alloys and more cost-effective nickel-based alloys.

1.4529 German numeral code. Is a super duplex stainless steel, the main components: 20Cr-25Ni-6Mo-1Cu-0.2N corresponding to the United States: N08926, 254SMo…
1.4529 (UNS N08926) has very high resistance to pitting and crevice corrosion in halide media and in acidic environments containing sulfur and hydrogen
It can effectively resist chloride ion stress corrosion, and also has good corrosion resistance and good stability in oxidizing and reducing media.
The mechanical properties are slightly better than 904L, and it can be used in the manufacture of pressure vessels from -196 to 400 ¡ãC.

It exhibits excellent weldability and can withstand very large amounts of pressure and weight.

Incoloy 800H and 800HT are typically used in parts above 1100¡ãF where creep and fracture resistance is required. The chemical balance allows nickel steel alloys to exhibit excellent resistance to carburizing, oxidizing and nitriding atmospheres. Incoloy 800HT will not become brittle even after prolonged use in the 1200-1600¡ã F range where many stainless steels become brittle. 800HT exhibits the excellent cold forming qualities normally associated with Nichrome.

Steel pipes can be disintegrated on the basis of its application. Typical applications of steel pipes are in the area of water pipelines, industrial water lines, oil pipe lines, cross country pipe line, agriculture and irrigation pipes, tube lines for natural gas, chemical industries, automobile industry, construction industries and other purposes.

Inconel 625 pipe fittings are available in ATSM B366 and ASME SB366 specifications. The tensile strength of Din 2.4856 Welded Buttweld Fittings is 1,35,000 psi 930 MPsand yield strength is 75,000 psi 517 MPa. UNS N06625 Cross are manufactured using push, cast, press, and forge processes. These fittings are available in the price range of Rs. 12,700 to Rs 2 lakh. We are among the leading manufacturers of alloy 625 reducer fittings and provide you the best quality product at an affordable price. Customer satisfaction is our ultimate goal. We assist in choosing the fittings as per the customers’ needs and specifications.

This nickel alloy also offers optimum resistance to environments where reducing and oxidizing conditions are encountered in process streams. This is beneficial in multi- purpose plants where such ¡°upset¡± conditions occur frequently.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

A234 Pipe Elbow the radius of curvature is 1.5 times the diameter (R=1.5D). We also accept all orders of CS Elbow A234 WPB up to and including 90 degree to suit your requirements.

Stainless steel grade 304 is the most commonly used stainless steel. Stainless steel grade 304N has better corrosion resistance than grade 302, and is mostly non-magnetic in nature; however when cold worked it acquires a slightly magnetic quality.

The 800H modification was to control carbon (0.05 to 0.10%) and grain size to (>ASTM 5) to optimize stress rupture properties.

These pipe fittings of B366 N06601 B366 N08825 B366 N10276 B366 N08020 materials, are used in the chemical industry, as well as in pressure vessels.

3A sanitary stainless steel 90 degree welded short elbow has strong corrosion resistance and long service life. The fitting is easy to install and features problem-free welding and assembly with the highest possible strength.

This means titanium can be used as a replacement for steel¡ªa major benefit, as it is 45% lighter than steel. It is twice as strong as aluminum and 60% denser.

Stainless steel is an alloy of iron that is resistant to rusting. It contains at least 11% chromium and may contain elements such as carbon, other nonmetals and metals to obtain other desired properties. Stainless steel’s resistance to corrosion results from the chromium, which forms a passive film that can protect the material and self-heal in the presence of oxygen.
A stainless steel pipe system is the product of choice for carrying corrosive or sanitary fluids, slurries and gases, particularly where high pressures, high temperatures or corrosive environments are involved. As a result of the aesthetic properties of stainless steel, pipe is often use in architectural applications.