90 Degrees ASTM B366 N08800 3D B16.9 Elbows

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Alloy K500 has approximately three (3) times the yield strength and double the tensile strength when compared with 400. MONEL K500 can be further strengthened by cold working before the precipitation hardening.

Monel K500, UNS N05500 (QQ-N-286), is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150¡ãF (-101¡ãC).

Una aleacion de niquel-cobre con alta resistencia y excelente resistencia a la corrosion en una variedad de ambientes acidos y alcalinos, especialmente para condiciones reductoras. Tambien tiene buena ductilidad y conductividad termica.

Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

Applications that deal with the marine environment are required to be resilient to the effects of saltwater. After all, the concentration of salt in marine water is about 3.5%, enough to corrode ordinary steels with no protective surface treatment.

Common trade names include alloy 400, UNS N04400, Monel alloy. Monel? is a registered tradename of Special Metals Corporation.

Monel 400 contains the same levels of nickel and copper as the natural nickel ore found.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

ASME Sb564 Alloy 400 Plate Flanges Monel 400 N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Generally, its corrosion resistance is very good in reducing environments, but poor in oxidizing conditions.

Monel 400 is a popular nickel-copper alloy commonly used in high performance applications. The alloy has high resistance to acidic and alkaline environments, high strength, good ductility and thermal conductivity. Monel 400® is suitable for use in the subzero to 1,000°F (538°C) temperature range and can only be hardened by cold work.

The high-temperature plasticity of the experimental alloy added with trace amounts of Mg, Cr and Co is obviously improved, and it exhibits certain superplasticity. At 1010¡æ, the strain rate sensitivity index m is 0.32, and the maximum elongation is 240%.

One of the most important characteristics of Monel 400 is that stress corrosion cracks do not occur in general, and the cutting performance is good. The structure of Monel 400 is single phase solid solution with high strength.

Monel K500 Bolts, also known as Alloy K500, are composed of a nickel alloy that combines the excellent corrosion resistance of Monel 400 with increased strength and hardness. These additional properties of Monel K500 bolts are the result of an age hardening process in which aluminum and titanium are added to a nickel-copper matrix, which is then precipitated throughout. Compared to 400, this process increases the yield strength of K500 by a factor of approximately 3 (110ksi vs. 45ksi) and doubles the tensile strength (160ksi vs. 83ksi). Monel K500 bolts will maintain their strength down to 1200¡ãF and even maintain their ductility down to -400¡ãF.

The Monel K500 is essentially a stronger, stiffer version of the Monel 400. It exhibits the same high corrosion resistance as this alloy, with added aluminum and titanium content for increased strength and hardness. Monel K500? is heat treated under controlled conditions to precipitate submicroscopic particles of Ni 3 (Ti, Al) throughout the material.

Alloy 400 (UNS N04400) is a nickel copper alloy with high strength (comparable to structural steel) and toughness. Alloy 400 also has excellent corrosion resistance in a range of media including seawater, hydrofluoric acid, sulphuric acid and alkalis.

The corrosion resistance of Monel K-500 is basically the same as Alloy 400, except that in the age hardened condition, Alloy K-500 has a greater tendency to stress corrosion cracking in certain environments. Monel K-500 has been found to be resistant to sour gas environments.

Monel 400 UNS N04400 1/2″ Class 150 RF the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Also known as alloy k500, Monel K500 fasteners and flanges are comprised of a nickel alloy that combines the outstanding corrosion resistance of Monel 400 with increased strength and hardness. Stronger than 400, alloy K500 even retains this strength in corrosive conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

The Alloy 400 Slip-on Flange is often seen in the marine industry as the alloy exhibits have good resistance to not only seawater but also to high velocity brackish water.

Typical applications for alloy K-500 pipe bend and elbow are pump shafts and impellers; doctor blades and scrapers; oil-well drill collars and instruments; electronic components; springs; and valve trim.

Monel 400 is widely used in Brine heaters, sea water scrubbers in tanker inert gas systems.

Monel 400 (also known as alloy 400) is an attractive option for industries where corrosion resistance is of the highest priority.

Nickel 400 Annealed Pipe, which is also referred to as a superalloy can be annealed at a temperature of 926¡ãC.

When utilized at subzero temperatures, these fasteners actually increase their tensile and yield strengths, while ductility and toughness are virtually unchanged. In addition, the flange face differs as flat face, raised face and ring type joint face as well. The Monel Slip On Flange is most useful with seamless pipes. The seamless pipes can easily slip onto the flange and reach the precise connection location. The ASTM B564 Monel 400 Lap Joint Flanges and other flanges can also come as threaded, forged, screwed or plate flange types.

The Alloy 400 Orifice Flange is a special type that is used to fit pipes together with an orifice. The minimum yield strength of the material is at 195MPa and the minimum tensile strength is 480MPa.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Over and above the nickel copper base, elements like aluminium and titanium in the chemistry of the Monel K500 Lap Joint Flange proves to be very fruitful. In fact, this modified chemistry along with the heat treatment that is given to the alloy under controlled conditions ensures that the particles of both Ti and Al have been precipitated in the matrix of Monel K500.

A286 (1.4980) bolts, also known as alloy 660 bolts, are a stainless steel alloy containing iron, nickel and chromium. A286 bolts are known for their high strength, creep resistance and oxidation resistance at elevated temperatures, once age hardened. As a result, A286 bolts provide high strength from room temperature to approximately 1300¡ãF (700¡ãC).