a quater jic male x three eighth nptf 4 inch 8 inch male stainless steel pipe fitting tee

The source raw material for ASTM A234 WPB steel pipe fittings may come from steel pipes such as ASTM A106 Gr.B and C. Also from steel plates like ASTM A285 Gr.C, ASTM A516 Gr 70, ASTM A572 etc.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

For the seamless steel pipe fittings refers to the fittings raw material from the seamless steel pipes and tubes. Thus the welded steel pipe fittings covers the fittings raw material from welded steel pipes.

Werkstoff No.1.4436 316 stainless steel fittings are resistant to atmospheric corrosion, as well as moderately oxidizing and reducing environments. Corrosion resistant in polluted marine atmospheres. It has excellent resistance to intergranular corrosion.

Copper-nickel or copper-nickel elbows are moderately strong and commonly found in marine saltwater applications.

ASTM A234 is standard of the pipe fitting material. However, this is indicating the properties of the material of various kinds of alloy steel and carbon steel. WPB is a steel grade in which W stands for weldable, B is grading B and P stands for pressure. Thus it is referring minimum yield strength.

There are 5 most common ASTM A234 WPB Elbow are in mainly in demand, the 45¡ã, 90¡ã and 180¡ã elbows, all three in the “long radius” version, and in addition the 90¡ã and 180¡ã elbows both in the “short radius” version.

The UNS S32760 Pipe Fittings have high tensile strength, durability, and excellent corrosion resistive property. The specifications of SA 815 WPS S32760 Elbow has criteria like size, standard, type and many more.

310S stainless steel has good high temperature resistance. When the temperature exceeds 800 [1], it begins to soften, and the allowable stress begins to decrease continuously. The maximum operating temperature is 1200 ¡ãC. Due to the high content of nickel (Ni) and chromium (Cr), it has good oxidation resistance, corrosion resistance, acid and alkali resistance, and high temperature resistance. After the content, the strength is improved due to its solid solution strengthening effect. The chemical composition characteristics of austenitic stainless steel are based on chromium and nickel with elements such as molybdenum, tungsten, niobium and titanium added. Therefore, it has high strength and creep strength at high temperature.

The main difference between stainless steel bottle caps and carbon steel bottle caps is the difference in material. The chemicals contained in stainless steel caps will keep the surface of the cap from rusting and corroding for a long time.

This nickel alloy is attacked in sulfur-bearing gases above approximately 700¡ã F and molten sulfur attacks the alloy at temperatures over approximately 500¡ã F.

Low carbon based wrought iron high yielding A860 WPHY 70 elbow fittings are chemically composed of metallic elements like – nickel, chromium, molybdenum, manganese, copper, vanadium, titanium, niobium, sulphur, silicon and phosphorus. Addition of these metal elements to the alloy makes it stronger and gives it increased resistance to corrosion. The yield strength of WPHY 70 material is 570 Mpa and its tensile strength is 485 Mpa.

Nickel Alloy 600, also sold under the brand name Inconel 600. It is a unique nickel-chromium alloy that is known for its oxidation resistance at higher temperatures.

ASTM a403 wp304 pipe bend is done to under control conditions to avoid carburization, decarburization and scaling surface. Heat treatment methods are stress relieving, hardening and annealing which strength the ductility and corrosion resistance properties.

S32205 is a duplex stainless steel with twice the strength of austenitic stainless steel. Duplex stainless steel composed of 21% chromium, 2.5% molybdenum and 4.5% nickel-nitrogen alloy. It has high strength, good impact toughness and good overall and local stress corrosion resistance. The yield strength of duplex stainless steels is twice that of austenitic stainless steels, a feature that allows designers to reduce weight when designing products, making this alloy more affordable than 316, 317L. This alloy is particularly suitable for use in the -50¡ãF/+600¡ãF temperature range. For applications outside this temperature range, this alloy can also be considered, but there are some limitations, especially when applied to welded structures. Duplex stainless steel has twice the compressive strength compared to austenitic stainless steel, and designers can reduce its weight compared to 316L and 317L. Alloy 2205 is particularly suitable for use in the -50¡ãF/+600¡ãF temperature range, and can also be used at lower temperatures under severe restrictions (especially for welded structures).

Alloy C-22 should not be used in service temperatures above 1250¡ã F due to the formation of detrimental phases which form above this temperature.

Grade 310 is a medium carbon austenitic stainless steel used in high temperature applications such as furnace components and heat treating equipment. It is used in continuous operation up to 1150¡ãC and intermittent operation at 1035¡ãC. The 310S grade is a low carbon version of the 310 grade. 310 stainless steel has good oxidation resistance and can be used continuously at temperatures up to 1140oC in the absence of reducing sulfur gases. With its high chromium content, 310 stainless steel has good corrosion resistance for improved high temperature performance.

The key properties of stainless steel 310S end cap fittings are their high chromium and moderate nickel content, making them key properties against oxidation, sulfidation, and other forms of hot corrosion.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Alloy 825 elbows are said to be non-magnetic and can work at high temperatures. It is resistant to atmospheric and water corrosion. It is also resistant to stress corrosion cracking and oxidizing environments.

The tee can be equal tee to connect three equally sized pipes or unequal tee to connect unequally sized pipes.Forgings or forming operations could be perfomred by hammering, pressing, piercing, upseting, rolling, extruding, bending, fusion welding, machining, or by a combination of two or more above operations. Which the point of manufacturing is not to produce injurious imperfections in the fittings.

Grade 316L, the low carbon version of 316 and is immune from sensitization (grain boundary carbide precipitation).

Nickel in elemental form or in alloys with other metals and materials makes a significant contribution to society today and is expected to continue to provide materials for a more demanding future. Nickel is a versatile element that forms alloys with most metals.

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

Our extensive technical experience and organized production procedures make us one of the most trusted suppliers of carbon steel fittings and flanges for large shipyards, manufacturing companies, chemical plants, oil refineries, machinery manufacturers, textile and fluid transport companies, etc. one.

Duplex UNS S32205 alloy is equally ferritic and austenitic in nature, and hence a widely used grade of Stainless Steel. UNS S32205 consist of 22% Cr and 3% Mo, 5 to 6% Ni alloyed stainless steel.

ASTM A420 is the standard specification for pipe fittings of carbon steel and alloy steel used for low temperature services. WPL6 is the most used grade material under A420.

Monel 400? is a nickel-copper alloy that is hardened by cold working only. The various types of available fittings are Monel Stub end, Monel Reducer, Monel End Cap Fittings, Monel tee, etc.

Stainless steel 316 butt weld joints are made of chrome-nickel-molybdenum alloy austenitic stainless steel. The material has good corrosion resistance, similar strength to 304 grade steel, and good hardness.

Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.