A182 F5 F9 F11 forged fittings Yield Strength Elongation

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

It is a standard specification defining typical chemical composition, mechanical properties, hardness requirement, preferential heat treatment, product marking, certification and other requirements, suitable for bolting used in pressure vessel service, valves, flanges and fittings. ASTM A193 defines both SI (Metric) and inch-pound units.

The alloying elements of A335 also impart higher corrosion resistance to the steel pipe. This also makes it the first choice for chemical companies.

Bolts and bolts are used in many applications in almost all industrial applications.

Chromium-molybdenum alloy flanges connect pipes, valves, pumps and other equipment to form a piping system. They are ideal for applications that convey corrosive or high temperature fluids or gases.

The alloy content of pipes that make up low alloy steel is less than 5%. High alloy steels, on the other hand, have an alloy content ranging from 5% to about 50%. Similar to most alloys, the working pressure capacity of alloy steel seamless pipe is about 20% higher than that of welded pipe.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P127

When connecting these parts, put gasket in the middle of two flanges, then tightening the flange screws, so the two will be connected together tightly.

The A320 Gr L7 stud material will undergo the following parametric tests – Impact Test, Tensile Test and Hardness Test according to the mechanical specification of A320 Grade L7 Bolts. The specification of A320 Gr L7 Hdg covers several grades of stainless steel including austenitic and ferritic stainless steels.

ASTM A320 L7 Stud Bolts are designed for low temperature performance. These fasteners are commonly used in valves, flanges, fittings and pressure vessels. The ASTM specification recommends a minimum impact value of 20-ft-lbf -150F for ASTM A320 L7 studs.

Alloy steel F12 bar offers some great properties such as strong construction, all-around durability, a wide range of sizes to choose from, and more.

ASTM A182 Grade F5 Flanges are suitable for connecting pipes of small bore size and without the requirement of welding. ASTM A182 GR F5 Flange belongs to the ASTM A182 specification. The dimensions of the flanges vary according to the ANSI, ASME and DIN standards. The flange sizes range from ? inches to 36 inches in nominal bore sizes. Navstar Steel is a leading supplier and manufacturer of these flanges in various sizes and types.

Flange connection has good strength and sealing, simple structure and low cost. It can be repeatedly disassembled.

A weld neck flange, also called a tapered hub flange or high-hub flange, is a kind of flange that can relocate stress to the pipes, ensuring a decrease in high-stress concentration at the bottom of the flange.

A335 pipe is highly resistant to rupture at high temperature and pressure. Chromium molybdenum tubes with resistance to hydrogen cracking and sulfide stress corrosion cracking are superior to carbon tubes.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.60

The high chromium content gives these forgings fittings very good resistance to moisture erosion, which also contributes to their high temperature strength and resistance to scaling at high temperatures.

ASTM A182 alloy steel F12 flanges are corrosion resistant. ASTM A182 alloy steel F12 flanges also have high dimensional accuracy. These ASTM A182 alloy steel F12 flanges also have a rust-proof finish. They are used in numerous industrial applications. These applications include the paper and pulp industry, the oil and gas industry, and more.

Alloy C276 (UNS designation N10276) is a nickel-molybdenum-chromium-iron-tungsten alloy
known for its corrosion resistance in a wide range of aggressive media.

The ANSI B16.5 Alloy Steel Slip On Flange is a flange type that allows the pipes to slip onto the flange and makes the connection in a precise locations.

Alloy 20 (Alloy 20) is an iron-based austenitic alloy developed to resist sulfuric acid corrosion. It has excellent resistance to sulfuric acid corrosion; it has strong resistance to phosphoric acid, nitric acid and chloride environments, chloride stress corrosion, pitting corrosion and crack corrosion. Therefore, alloy 20 has the name of anti-corrosion alloy; it has a wide range of applications: such as: chemical, food, medicine, power production and plastics industries will use it. For resistance to pitting corrosion and chloride corrosion, stress corrosion cracking problems, etc., alloy 20 is often used.

F5 A182 Pipe Flanges tends to have a fairly high electrical conductivity amongst other wrought alloy steels in the same category. It has a comparatively high base cost and high embodied energy. ASTM A182 is the Standard Specification for Forged Stainless Steel Pipe Flanges and Stainless Steel Forged Fittings.

Inconel600 is suitable for welding with the same material or other metals by any traditional welding process, such as tungsten electrode inert gas welding, plasma arc welding, manual sub-arc welding, metal inert gas shielded welding, molten arc inert gas shielded welding, and pulsed arc welding. Welding is the preferred solution. When using manual arc welding, it is recommended to use a shielding gas mixed with various components (Ar+He+H2+CO2).
Welding of Incoloy 825 must be carried out in the annealed condition and cleaned with a stainless steel wire brush to remove stains, dust and various markings. When welding the root of the weld, extreme care must be taken (Argon 99.99) to obtain the best quality of the root weld so that the weld does not produce oxides after the root has been welded. Color from the weld heat-affected zone should be removed with a stainless steel brush while the weld area is not cool.

ASTM A182 Alloy Steel Forged Fittings are manufactured according to the ASTM A182 specification, which covers high pressure and high temperature service flanges covered by ASME B16.11, MSS-SP-79/ 83/ 95/ 97 and BS3799 standards.

Alloy steels are used in a range of demanding applications in the aerospace and power (nuclear) industries. Adding other elements gives alloy steel extra strength.

The carbon content of 4140 alloy steel pipe is 0.38-0.43%, the manganese content is 0.75-1.00%, the phosphorus content is 0.04%, the sulfur content is 0.04%, the silicon content is 0.15-0.35%, the chromium content is 0.8-1.10%, and the molybdenum content is 0.8-1.10%. is 0.15-0.25 % maximum in its composition. The material can be heat treated to anneal and normalize in air, or quench and temper in polymer or oil.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P138

Alloy Steel Flanges is a forged or cast ring of steel designed to connect mechanically sections of pipe or join pipe to a pressure vessel, valve, pump any other piece of equipment.

The most common application for A182 F2 round bars is shafts. It has various alloying elements that enhance its mechanical properties.

A335 P22 is a seamless tube made of ferritic alloy stainless steel. Chemically, the alloy of SA335 P22 material contains trace amounts of carbon, manganese, sulfur, silicon and phosphorus. The main additives in the alloy are molybdenum and chromium, which give stainless steel excellent mechanical properties. Tensile strength, corrosion resistance, hardness and other properties are enhanced and improved. Molybdenum reduces the brittleness caused by the addition of chromium.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P132

This specification covers forged low alloy flanges for use in pressure systems manufactured to specified dimensions or industry standard dimensional specifications.

To be sure, huge numbers of the reactions of Alloy Steel F9 Slip On Flanges meddle with each other, requiring the utilization of process models to help in analysing alternatives, improving contending reactions, outlining productive commercial practices. The specification is for high temperature pressure services. The SA 182 Gr F9 Steel Pipe Flanges come in the size range of ? inches to 48 inches with dimensions varying according to the ASTM, ASME and other international standards.

SA 182 Socket Weld Flanges are joined by inserting the pipe into the socket end and applying a fillet weld around the top. This allows for better flow of fluid or gas inside the pipe and smooth holes.

Pipe to ASTM A335 P11 can be cold drawn or hot rolled. Each tube shall be reheated for heat treatment – fully or isothermally annealed, normalized and tempered at a temperature not lower than 1200¡ãF (650¡ãC). Each pipe length shall be hydrostatically tested to ASTM A335 P11, along with dimensional inspection and visual inspection. Longitudinal or transverse tensile tests, flattening tests or bending tests are carried out for each heat.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P129