A182 F53 2507 special flange Super Duplex DIN 1.4410 flange

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

ASTM A240 is a normative standard covering several chromium-based stainless steel grades manufactured in sheet, sheet, or ASTM A240 Gr 2205 strip.

It has the nominal composition of 22Cr-5Ni-3Mo-N with P number 10H.

S32760 was originally developed as a seawater resistant material for pump applications in the North Sea.

2507 is a super-duplex (austenitic-ferritic) stainless steel for service in highly corrosive conditions.

Duplex Steel UNS S31803 Seamless Pipes are widely used in various applications in the industry. These ASTM A790 Duplex Steel S31803 Pipes are made up of a combination of microstructure of austenitic and ferritic grains, which gives them unique properties. These properties include a high resistance to corrosion, excellent strength and toughness, and good weldability.

Compared with ferritic stainless steel and austenitic stainless steel, duplex stainless steel pipe has good welding performance. It is neither like the welding heat affected zone of ferritic stainless steel, because of the grain coarsening, the plastic toughness is greatly reduced, nor like austenitic stainless steel, it is more sensitive to welding hot cracks.

Alloy 2205 (UNS S32305/S31803) is a 22% chromium, 3% molybdenum, 5-6% nickel, nitrogen alloy duplex stainless steel plate that, in addition to high strength and excellent impact toughness, also has high general, Localized and stress corrosion resistance.

ASME SA 479 UNS S32205 Fastener is a corrosion resistant and high strength super alloy that can be used in low temperature ranges up to 1300 degrees Fahrenheit.

ASTM A479 Super Duplex UNS S32750 Fasteners is a mixed microstructure of austenite and ferrite (50/50) which has improved strength over ferritic and austenitic steel grades.

UNS S31803 Bolted Fasteners are used in marine, agricultural, chemical, construction, shipping, aviation, nuclear and industrial equipment.

S32760 is a super duplex stainless steel with a ferritic-austenitic microstructure.

UNS31803 has been supplemented by S32205 (F60) which dual conforms to S31803 but has a higher minimum N, MO, NI and Cr which guarantees a better corrosion resistance.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

 ANSI B16.5 Super Duplex Stainless Steel S32750 Orifice Flange provides excellent resistance to a wide range of corrosive environments, including seawater, acidic solutions, and chloride-containing environments. Super Duplex F53 WN Flange exhibits higher corrosion resistance than standard duplex stainless steels.

ASTM A240 Type 2507 Super Duplex Plates must comply with ASTM A240. It is a specification of chrome and chrome-nickel stainless steel plate. Super Duplex 2507 plates are used in general applications and containers.

The notch ductility of SA 240 S32760 Sheet performs well at sub-zero temperatures, down to the -50¡ãC range, while performing well at ambient temperature.

The material for UNS S32760 Stud Bolts is about 10% lighter when compared to grade 316 stainless steel. The Stud Bolt S32760 demonstrates high performance at cryogenic temperature settings as well. Which means that the ASTM A1082 UNS S32760 has good sub-zero notch ductility properties down to a temperature of minus 50¡ãC.

ASTM A240 Type 2205 Duplex Sheet provides a maximum Brinell hardness value of approximately 290 in the annealed condition.

Super Duplex 2507 stud bolts (EN 1.4410) are made of a stainless steel alloy containing 25% chromium, 4% molybdenum, and 7% nickel. Duplex 2507 is known for its high strength and excellent localized corrosion resistance to chloride.

The different face types have their own advantages in piping applications.

Super Duplex S32760 Bar proves to be an excellent replacement for austenitic grades in marine environments. Super Duplex S32760 round bar (ASTM A276/ ASTM A479) exhibits good heat resistance up to 300¡ã.

Super Duplex stainless for e.g. alloy UNS S32750, has a mixed microstructure of both austenite as well as ferrite in an equal or 50/50 ratio.

Compared to 317L stainless steel, duplex steel has excellent resistance to chloride pitting and crevice corrosion. The alloy has excellent corrosion resistance to seawater and most concentrations of sulfuric acid. In addition, it is resistant to sulfide stress corrosion cracking (sour gas environments)

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

Super Duplex 2507 is used in environments containing high levels of chlorides or dissolved oxygen, such as seawater cooling, salt evaporation, and desalination, geothermal wells.

S31803 has been supplemented by S32205 (F60) which dual conforms to S31803 but has a higher minimum N, MO, NI and Cr which guarantees a better corrosion resistance.

ASTM A182 Super Duplex F55 Hex Bolts is used for Pumps, valves, chokes, Connectors, Pipework/flanges, Oil & Gas components, Manifolds, etc. The resulting savings in weight of ASME SA 182 Super Duplex S32760 Hex Bolts can dramatically reduce the overall cost of fabrication. Anneal Heat this ASME SA479 Super Duplex S32760 Hex Bolts to 1025 Degree C ¨C 1120 Degree C ensuring sufficient time is allowed for the centre to achieve furnace temperature and hold for a time commensurate with the ruling section, followed by water quenching.

While Duplex 2205 is the most common duplex product we supply, we can also deliver Duplex 2304 and Duplex 2207 with reduced lead times as these alloys are stocked. Alloy 2205 (UNS S32305/S31803) is a 22% chromium, 3% molybdenum, 5-6% nickel, nitrogen alloyed duplex stainless steel pipe with high general, localized, and stress corrosion resistance properties in addition to high strength and excellent impact toughness.

The pressure capacities of the flanges can also be expressed in pressure numbers. The astm a182 f53 uns s32750 flange types come in pressure numbers ranging from PN6 through PN64.

2205 is the standard duplex grade and is more economical than most other duplex grades.