A182 F53 2507 special flange used in fire-fighting systems and injection and ballast water systems

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

2205 flange has good general corrosion resistance, high resistance to chloride stress corrosion cracking, as well as pitting and crevice corrosion.

Compared with ferrite, it has higher plasticity and toughness, no room temperature brittleness, significantly improved intergranular corrosion resistance and welding performance, and maintained 475 ¡æ brittleness, high thermal conductivity and Superplasticity of ferritic stainless steel. Compared with austenitic stainless steel, its yield strength is significantly improved, and its resistance to intergranular corrosion, stress corrosion, corrosion fatigue and abrasion is significantly improved.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The S31803 fastener series demonstrates the properties of ferritic and austenitic stainless steels. These fasteners exhibit excellent resistance to crevice corrosion, stress corrosion cracking and pitting corrosion in harsh environments. In addition, these are excellent in resistance to chloride and sulfide stress corrosion environments.

Though it is important to keep in mind that pitting corrosion can be a concern in chloride solutions when oxidizing media is present. In these conditions, the passive (protective) layer of the Duplex 2205 material may be compromised in localized pitting may occur.

We offer a complete range of 2205 Duplex Steel Fasteners such as Bolts, Nuts, Washers, Screws, Connecting Rods and Duplex Steel Screws. We also offer super duplex fasteners in different sizes, shapes, features and thicknesses according to customer requirements.

The steel has excellent resistance to chloride stress corrosion cracking, high thermal conductivity, and a low coefficient of thermal expansion.

Compared to 317L stainless steel, duplex steel has excellent resistance to chloride pitting and crevice corrosion. The alloy has excellent corrosion resistance to seawater and most concentrations of sulfuric acid. In addition, it is resistant to sulfide stress corrosion cracking (sour gas environments)

The material of the super duplex S32750 sheet has increased tensile strength and yield strength. Super Duplex Steel UNS S32750 plate has good ductility and toughness. AISI S32750 plate has good corrosion resistance compared to Duplex. The material of the super duplex steel S32750 plate has higher corrosion resistance.

2507 (PREN 40-45), with 25-26 Cr and increased Mo and N compared with the 25Cr grades. A super austenitic-ferritic duplex stainless steel with exceptional strength and corrosion resistance ideal for chemical process, petrochemical, and seawater applications.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

They are resistant to general corrosion. We are suppliers of ASME SA182 Duplex Steel UNS S32205 Weld Neck Flanges to sea water and power generation equipment.

Duplex 2205 fasteners are made from cost-effective, long-lasting and corrosion-resistant steel. The grade of steel used to make fasteners can be ferritic, austenitic or dual phase steel. Duplex materials have the strength qualities of ferritic steels and the corrosion-resistant qualities of austenitic steels.

The yield strength is also higher, allowing component designers to reduce section size for load-bearing applications.

Super Duplex Steel UNS S32760 are dual phase austenitic-ferritic duplex fasteners manufactured from alloy containing chromium, nickel and molybdenum with restricted carbon content and minimum PREN42. Zeron washers have high strength, resistance to pitting, stress corrosion cracking, erosion and corrosion fatigue, crevice corrosion resistance.

ASTM A240 Type 2205 Duplex Sheet provides a maximum Brinell hardness value of approximately 290 in the annealed condition.

The duplex microstructure gives this grade high strength UNS S32750 a low coefficient of thermal expansion and higher heat conductivity than austenitic steels and is suitable for working temperatures up to 300¡ãC.

The combination of the ferritic phase and austenitic phase provides both high strength and excellent corrosion resistance.

Supplied in the annealed condition, it has a yield strength of 80ksi (550Mpa), which is higher than most austenitic and duplex grades.

Super Duplex Stainless steels, which combine high strength and excellent corrosion resistance in many environments, have found applications in chemical and process industries.

2507 Duplex Plate also exhibit better ductility and toughness compared to ferritic stainless steels, but they do not provide these properties as successfully as austenitic stainless steels.

Astm A182 F51 flange is made up of carbon, chromium, manganese, silicon, phosphorus, sulfur, nickel, nitrogen, molybdenum and iron.

Stainless Steel Duplex SAF 2205 Hex Bolts are used in machinery and construction and can be used with nuts or threaded holes. Since they can be tightened with a wrench, fully threaded hex bolts are specially designed to work more efficiently. Additionally, 2205 hex bolts are stronger than standard stainless steel, meaning they can be used for jobs that require high workloads and good corrosion resistance.

Grade 904L is less resistant to nitric acid than grades 304L and 310L, which are free of molybdenum. This steel grade needs to be solution treated following cold working, to achieve maximum stress corrosion cracking resistance under critical environments

Some steels also contain Mo, Cu, Nb, Ti, N and other alloy elements. Compared with ferrite, it has higher plasticity and toughness, no room temperature brittleness, significantly improved intergranular corrosion resistance and welding performance, and maintained 475 ¡æ brittleness, high thermal conductivity and Superplasticity of ferritic stainless steel. Compared with austenitic stainless steel, its yield strength is significantly improved, and its resistance to intergranular corrosion, stress corrosion, corrosion fatigue and abrasion is significantly improved.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Duplex alloys prove themselves useful in applications where ordinary steel grades are susceptible to failure. The microstructure of the Duplex Pipe Material partially consists of both austenite and ferrite regions.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

2205 dual-phase steel fasteners have some excellenut mechanical properties, which may be due to the balanced austenitic and ferritic microstructures in the alloy.

The UNS S32750 standard of Pipe Fittings consists of 25% chromium, 4% molybdenum, and 7% nickel. The UNS S32750 Pipe Fittings have a 50-50 microstructure of ferritic and austenitic steel grades with improved strength.

Alloy 2205 duplex stainless steel plate has better pitting and crevice corrosion resistance than 316L or 317L austenitic stainless steel in almost all corrosive media.

Duplex 2205 pipe is stainless steel. It belongs to a family of stainless steels called duplex steels. There are different groups of this material. This series of pipes can be cold drawn, hot rolled and welded. Alloy 2205 seamless tube is cold drawn, it has less absolute roughness.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.39

The pressure capacities of the flanges can also be expressed in pressure numbers. The astm a182 f53 uns s32750 flange types come in pressure numbers ranging from PN6 through PN64.

Las laminas duplex son grados austenitico-ferriticos con la misma composicion. Esta dise?ado para proporcionar laminas resistentes a la corrosion y de alta resistencia. Utiliza un mayor contenido de cromo hasta un 28%. La placa ASTM A240 UNS S32750 tiene un limite elastico minimo de aproximadamente 77 ksi y una resistencia a la traccion de al menos 730 MPa. Se estiro un 25% en estado recocido.