a335 pipe alloy p5 p9 p11 p12 p22 steel pipe

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

ASTM A335 alloy is the steel pipe defined according to the production bill of materials (or material). As the name implies, the alloy pipe and the seamless steel pipe are defined according to the production process (seamless seamless). The difference between the seamless pipe is the welded pipe, including the straight seam welded pipe and the seamless steel pipe. Spiral tube.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.23

The ASTM A194 specification covers a wide variety of carbon, alloy, and martensitic stainless steel nuts in sizes ranging from 1/4 to 4 inches and metric M6 to M100 nominal. It also covers austenitic stainless steel nuts in the size range of 1/4 inch and M6 nominal and above. These nuts are used for high pressure or high temperature service, or both.

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

A182 pipe flanges tend to have fairly high electrical conductivity among other wrought alloy steels in their class. It has a higher base cost and higher embodied energy.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

We offer F9 Alloy Steel Flanges that have superior corrosion resistance and ductility due to the small amount of Chromium and Molybdenum. A182 F9 Alloy Steel Flanges is for use in small size and high pressure piping systems. Due to the small amount of chromium and molybdenum it has superior corrosion resistance and ductility.

Alloy steel UNS K12822 round bars are widely used in numerous industries for the manufacture of different kinds of components. We provide a full range of alloy steel 15Mo3 round bars which are widely used in engineering, construction and other industries.

The Alloy Steel Weld Neck Flange has a welded neck onto it that holds larger pipes in place for easy welding and installation.

ASTM A182 Alloy Steel Pipe Fittings are very easy to install and have a low hub due to the pipe going into the fitting before welding.

Grade 1 alloy steel plate has very high corrosion resistance, but it is increasingly expensive. Our alloy steel products are known worldwide for their reliability and quality.

800H can resist corrosion of many corrosive media. Its high nickel content makes it resistant to stress corrosion cracking in aqueous corrosion conditions. The high chromium content provides better resistance to pitting and crevice corrosion cracking. The alloy has good corrosion resistance to nitric acid and organic acids, but limited corrosion resistance in sulfuric acid and hydrochloric acid. Good corrosion resistance in oxidizing and non-oxidizing salts, in addition to the potential for pitting corrosion in halides. It also has good corrosion resistance in water, steam and mixtures of steam, air and carbon dioxide.

ASTM A320 bolts are suitable for low temperature service down to -150¡ãF and have a minimum Charpy impact value of 20-ft-lbf at this temperature. ASTM A320 Hex Bolts must obtain the durability and service of high temperature or high pressure and corrosion resistant steel. ASTM A320 Stud Bolts are available in different sizes and patterns, our premium ASTM A320 Grade L7 AS Bolts are in high demand in the market due to their speculative properties and specifications.

Several ANSI/ ASME standards use materials that are forged or cast to produce Cast AS Blind Flanges.

ASTM A193 Grade B7 bolts and studs are made from chrome molybdenum steel and are quenched and tempered (heat treated) to achieve the desired mechanical properties (strength). Grade B7 is the most commonly used A193 bolt grade in construction.

Inconel600 is suitable for welding with the same material or other metals by any traditional welding process, such as tungsten electrode inert gas welding, plasma arc welding, manual sub-arc welding, metal inert gas shielded welding, molten arc inert gas shielded welding, and pulsed arc welding. Welding is the preferred solution. When using manual arc welding, it is recommended to use a shielding gas mixed with various components (Ar+He+H2+CO2).
Welding of Incoloy 825 must be carried out in the annealed condition and cleaned with a stainless steel wire brush to remove stains, dust and various markings. When welding the root of the weld, extreme care must be taken (Argon 99.99) to obtain the best quality of the root weld so that the weld does not produce oxides after the root has been welded. Color from the weld heat-affected zone should be removed with a stainless steel brush while the weld area is not cool.

ASTM A335 P5 pipe can be fully annealed or isothermally annealed, normalized and tempered as heat treatments to increase hardness. This grade is available in welded and seamless pipe, A335 P5 welded pipe is available in different wall thicknesses and diameters.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P121

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

Pipe Fittings are usually socket welded or threaded. The high chromium content gives these forgings fittings very good resistance to moisture erosion

Products made from alloy steel perform far better than those made from carbon steel. Although they are less expensive than stainless steel grades, they are less resistant to corrosion than stainless steel but more resistant than carbon steel pipe.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.67

This is useful for selecting bolts with different strength levels for different high pressure and high temperature applications. ASTM A193 grade b7 hex bolts and other types have a minimum tensile strength of up to 125ksi.

ASTM A320 L7M Grade AS Fasteners are commonly used in oil and gas exploration and processing equipment – piping, piping and heat exchangers.

The addition of molybdenum increases the softening resistance of sa335 grade p5. It also prevents grain growth. In addition, molybdenum increases the resistance to brittleness that can occur in chromium steels. This chrome molybdenum alloy a335 p5 steel pipe is ideal for applications that carry fluids such as oil, water and gas at very high pressures and temperatures. astm a335 p5 alloy steel pipe is ideal for forming operations such as bending and flanging, and fusion welding.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.65

All chrome molybdenum steel sheets are sedated and heat treated in accordance with ASTM A387, which also specifies minimum and maximum levels of the following elements in steel: Chemicals of Carbon, Manganese, Phosphorus, Sulfur, Silicon, Chromium, Molybdenum, Nickel, Vanadium requirements, columbium, boron, nitrogen, aluminum, titanium and zirconium. A387 boards must undergo product, chemical and tensile testing (documented in the MTC or material test certificate) – must meet specific requirements for tensile strength, yield strength and elongation.

ASTM A182 Grade F5 Flanges are suitable for connecting pipes of small bore size and without the requirement of welding. ASTM A182 GR F5 Flange belongs to the ASTM A182 specification. The dimensions of the flanges vary according to the ANSI, ASME and DIN standards. The flange sizes range from ? inches to 36 inches in nominal bore sizes. Navstar Steel is a leading supplier and manufacturer of these flanges in various sizes and types.

These ASTM A182 alloy steel F5 F9 F11 F12 F22 F91 pipe fittings are corrosion resistant. ASTM A182 alloy steel F5 F9 F11 F12 F22 F91 fittings also have high dimensional accuracy.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Chromium Molybdenum Alloy Steel or Chromium Molybdenum, CrMo is an alloy steel used for high temperature and high pressure service. Chromium molybdenum is used in power generation and petrochemical industries for its tensile strength, corrosion resistance and high temperature strength.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

The thickness and the inner diameter of the flange will be as per the size of the pipe for which this welding neck flange is being made.

sa335 P5 P5 materials used to make ASTM A335 pipes etc. must meet chemical composition, tensile properties and SA335 P5 hardness requirements. This type of alloy steel pipe is used in applications that require high temperature service. ASTM A335 P5 Pipe Supplier’s Composition, A335 P5 Allowable Stress contains lesser amounts of Nickel and Manganese as they increase the hardness of the pipe.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.36