a335 wp pipe bend

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Although the properties of the fitting depend on the alloy used to manufacture them. Another process that improves the mechanical properties of ASTM A182 F9 Alloy Steel Flanges is the forging process. These Grade F9 Weld Neck Flanges can also be reused and are meant for high pressure applications. This is the reason as per the specification they have to be rolled or forged.

The creep strength (for 1% elongation at 105 hours) of A182 Grade F5 may reach 170 MPa at about 450 ¡ãC.

Chromium-Molybdenum alloy steel flanges dimensions has been widely used in the many areas. Their utilization can be seen in areas such as steam power equipment, petrol chemical industry, and high temperature services.

The plates are annealed in different condition which offers them strength. Since these plates are to be worked at high temperatures and pressure environment therefore the elements included in it matters a lot. What elements are added in the manufacturing add different properties for example, high level of chromium adds excellent corrosion resistance. It also offers excellent oxidation resistance. Resistant to oxygen is important in petrochemical and gas industries and therefore these plates are used.

The high chromium content gives these forgings fittings very good resistance to moisture erosion, which also contributes to their high temperature strength and resistance to scaling at high temperatures.

Products made from alloy steel perform far better than those made from carbon steel. Although they are less expensive than stainless steel grades, they are less resistant to corrosion than stainless steel but more resistant than carbon steel pipe.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.67

The addition of elements such as silicon and manganese through heat treatment provides alloyed steel with improved properties and additional benefits, such as increased corrosion resistance or increased reliability. Alloy steels are also found in applications where their response to magnetism is important, such as in transformers and electric motors.

Weld Neck Flange is flanges that designed to be joined to a piping system by butt welding. This kind of flange include lots of specification.

Users of SA182 Chrome Moly Gr.f9 forged bar do not rely solely on external coatings or finishes.

Our alloy steel blind flanges are mainly caused by environmental factors such as wind exposure, man-made pollution and high temperature, and are more serious near the ocean, which is the main cause of seawater pollution.

ASTM specifications recommend a minimum Charpy impact value for ASTM A320 L7 Stud Bolts to be 20-ft-lbf @ -150F. The Charpy impact test determines the total amount of energy that is absorbed by a material during fracture, thereby indicating the material¡¯s notch toughness.

Our Alloy Steel ASTM A182 F5 Weld-neck Flanges are supplied to aid industrial, high pressure services like condensers, boilers, evaporators, heat exchangers, etc. Alloy steel F5 A182 flanges is also available in the form of lap joint flanges, plate flanges, threaded flanges, reducing flanges and many more. These flanges are widely used in power generation industry, gas processing industry, pharmaceutical industry, heat exchangers industry, sea water equipment industry, oil drilling companies and many more.

A182 pipe flanges tend to have fairly high electrical conductivity among other wrought alloy steels in their class. It has a higher base cost and higher embodied energy.

The chromium content in the A335 p9 pipe makes it highly resistant to corrosion. Therefore, A335 p9 has excellent high temperature oxidation resistance. In addition to chrome, Astm A335 p9 alloy steel pipe coated with black paint or anti-corrosion oil shows good corrosion resistance. It can also be galvanized with zinc. Galvanizing increases its resistance to atmospheric corrosion.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P147

Alloy Steel Flanges are made in different steel alloys. The flanges vary in dimensions and types. There are ? inches through 48 inches of nominal diameter sizes of flanges.

These are said to be specifications for alloy flanges for high pressure and service. The 3% carbon content of these flanges provides a lot of room for improved weldability, which also increases their overall strength.

The material contains carbon, manganese, phosphorus, sulfur, silicon, 8% chromium and molybdenum in a mixture. SA 335 grade P5 alloy steel pipe has similar strength to most austenitic stainless steel grades, with a minimum yield strength of 205MPa and a minimum tensile strength of 415MPa.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P120

They have a minimum yield strength of 105ksi. There are different types of bolts and bolts for different types of applications such as ASTM A193 gr b7 hex bolts.

A335 P9 steel pipe material also contains manganese, silicon, carbon and phosphorus in its composition. The addition of these materials makes the material stronger with higher yield and tensile strengths. Due to the high chromium content, the redox effect is high.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.37

These Alloy Steel F12 Lap Joint Flanges are made up of in dissimilar grades of standard ranges and meet its terms through national and international standards. Alloy Steel ASTM A182 F12 flanges are exceptionally resistant to corrosion in nature. In the interim, fabricators can cut pipe to length without inconvenience for these ASTM A182 F12 Alloy Steel flanges.

Chromium Molybdenum Alloy Steel or Chromium Molybdenum, CrMo is an alloy steel used for high temperature and high pressure service. Chromium molybdenum is used in power generation and petrochemical industries for its tensile strength, corrosion resistance and high temperature strength. Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

ASTM A182 Low Alloy Steel flanges as well as the other types of alloys. The ASTM A 182 specification specifies flanges for high pressure services.

Our ASTM A182 F5 alloy steel blind flanges are used in auxiliary industrial high pressure services such as heat exchangers, condensers, evaporators, boilers, etc.

Blind flanges can also be used to seal a nozzle opening on a pressure vessel.

Alloy steel pipes and tubing are the best choice for stress corrosion cracking (SSC). These also apply to environments where the problem is pitting and crevice corrosion. These tubes and tubes are available within machining allowances and tolerances.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.34

The specification for ASTM A320 Grade L7m materials covers alloy steel and stainless steel bolting materials for low temperature applications. ASTM A320 L7 Studs can also be used in applications with ambient temperatures up to -150oF. ASTM A320 grade L7m bolts and ASTM A320 bolts have a minimum Charpy impact value of 15 foot-pounds at this temperature.

Standard ASTM A193 B7 fasteners typically have a common bare metal finish. However, ASTM A193 Grade B7 studs can be galvanized, hot-dip galvanized, xylan coated, teflon coated if requested by the buyer. Coating ASTM A193 B7 fasteners can help improve the corrosion resistance of fasteners. This ASTM A193 Grade B7m bolt is typically used to fasten medium high temperature service materials. These bolts are liquid quenched from 50¡ãF to 900¡ãF and they can be air quenched from -40¡ãF to 900¡ãF.

Alloy Steel F11 Flanges specifications are also mentioned and the face type starts from flat face, raised face, ring type joint and many more.

ASTM A182 lap flanges are known by a variety of names, including support flanges, loose flanges, loose ring flanges, and van stone flanges.

Although acceptable fouling levels are considered beneficial to the alloy, in moderate cases, fouling deposits on Astm A182 F9 flange surfaces can act as a barrier to excessive corrosion. When flanges are produced using specification ASTM A182, they work well at high temperatures, albeit in applications with high pressure.