Alloy 20 Carpenter 20CB-3 hex head bolt full thread DIN933

Since Inconel uses nickel as its primary alloying agent, the use of Inconel 718 fasteners at elevated temperatures has no negative effect on the application or the equipment being used.

Applications in air pollution control include stack liners, ducts, dampers, scrubbers, stack-gas re-heaters, fans and fan housings.

Inconel 600 is a nickel-chromium alloy with good oxidation resistance at higher temperatures, with good resistance in carburizing and chloride containing environments.

Hastelloy C-276 is a very popular alloy for us because of its high corrosion resistance in a wide range of environments. It has excellent resistance to oxidizing aqueous media, including wet chlorine and mixtures of oxidizing acids containing nitric or chloride ions.

Nickel Alloy 600, also sold under the brand name Inconel 600.

The chemical composition of Monel K500 ASTM is approximately 65% nickel, 30% copper and 3% aluminum. Monel 500 exhibits excellent corrosion resistance with added high strength corrosion fatigue and erosion resistance. Monel K500 fasteners are non-magnetic at high and low temperatures. The material has the same corrosion resistance as Monel Class 400.

The high molybdenum content of Hastelloy?* C276 provides the alloy with its excellent resistance to pitting and crevice corrosion.

INCONEL 625 is used in offshore and aerospace industries, but also in pollution control equipment.

Hastelloy B3 has excellent resistance to hydrochloric acid at all concentrations and temperatures. In addition, it greatly improves structural stability compared to previous B-type alloys, reducing concerns during welding, fabrication and service.

Alloy 718 fasteners (UNS N07718 fasteners) are very strong and resistant over a wide temperature range (-423 to 1300F).

Incoloy A-286 stud bolt is a Fe-25Ni-15Cr base superalloy reinforced by molybdenum, titanium, aluminum, vanadium and trace boron. It has high yield strength and durability, creep strength below 650 ¡æ, good processing plasticity and satisfactory welding performance. Incoloy A286 is a Fe-25Ni-15Cr based superalloy reinforced with additions of molybdenum, titanium, aluminum, vanadium and trace amounts of boron. It has high yield strength, durability and creep strength, good workability and good weldability at 650¡æ.

Restricted carbon and columbium stabilization allows the use of welded fabrication in corrosive environments, usually without post-weld heat treatment. Alloy 20 with 33% nickel is practically immune to chloride stress corrosion cracking. Alloy 20 fasteners have impact toughness resistant to chloride stress corrosion cracking, pitting and crevice corrosion.

Fasteners play a critical role in the construction of all sorts of everyday objects. If you¡¯ve done any DIY projects, you¡¯ve likely used fasteners to help get the job done.Fasteners are used for fastening and securing materials such as wood, metal, plastic, or concrete. They include nuts and bolts, threaded rods, structural bolts, machine screws, wedge anchors, washers, rivets, and more in a variety of types and sizes, including metric and inch.

Nimonic 80a Nuts are low creep superalloy fasteners made from alloys containing over 50% nickel, 20% chromium, and additions of titanium and aluminum. Nimonic Alloy 80a fasteners can withstand very high temperatures.

Monel 400 es una de las pocas aleaciones que conserva la resistencia a temperaturas bajo cero, asi que utilicela en estas situaciones.

Age-hardenable Inconel 718 Heavy Duty Hex Bolts can be easily fabricated, even into complex parts. Inconel UNS N07718 bolts are also commonly found in gas turbine blades, seals and combustors, as well as turbocharger rotors and seals, electric submersible well pump motor shafts, high temperature fasteners, chemical processing and pressure vessels, etc. Other uses for this alloy tend to be in gas turbine components and cryogenic storage tanks. Jet engines, pump bodies and parts, rocket engines and thrust reversers, nuclear fuel element gaskets, hot extrusion tools.

Alloy B (UNS N10001) was developed to resist hydrochloric acid. Hastelloy B2 has replaced it. Alloy B3 (UNS N10675) is a newer variant with higher thermal stability. These alloy B2 bolts are a wrought nickel molybdenum alloy that can be used in the as-welded condition. It is highly resistant to hydrochloric acid of all concentrations and temperatures. Known as UNS N10665 bolts, these bolts are also resistant to stress corrosion cracking and pitting.

Monel K500 is a nickel-copper alloy that combines the excellent corrosion resistance of Monel 400 (link) with the added benefits of higher strength and hardness. Performance can be improved by adding aluminum and titanium to the nickel-copper matrix and by heating under controlled conditions to precipitate submicroscopic particles of Ni3 (Ti, Al) throughout the matrix. This is commonly referred to as age hardening or aging.

The alloy is ductile and readily forms Inconel 601 fasteners. It has high mechanical strength, good toughness and excellent corrosion resistance.

Hastelloy C22, also known as alloy C22, is a versatile austenitic nickel-chromium-molybdenum-tungsten alloy with enhanced resistance to pitting, crevice corrosion and stress corrosion cracking.s. It is available in the form of plates,
sheets, strips, billets, bars, wires, pipes, tubes, and covered electrodes.

Inconel Alloy 718 ? is an alloy containing significant amounts of nickel, chromium and molybdenum. It is one of the most popular nickel-based superalloys and is widely used for its excellent resistance to corrosive environments such as crevice and pitting corrosion.

These Inconel 718 fasteners do not lose strength despite exposure to extreme temperature ranges. Alloy 718 bolts are used in cryogenic storage tanks due to their good mechanical and physical properties in extremely cold environments.

Another feature of HASTELLOY-X fasteners is their excellent forming and welding characteristics. It can be forged and can be cold worked due to its good ductility. Common applications for Hastelloy x include use in aircraft furnaces and chemical process components.

Alloy 926 (1.4529) screws are the perfect replacement for 316L when higher corrosion resistance is required without increased strength. Alloy 926 fasteners are considered a 6-molybdenum alloy (6-molybdenum or 6% molybdenum), similar to sister alloys AL6XN and SMO 254. In the stainless steel category, these 6 molybdenum alloys are considered very corrosion resistant.

Alloy 20 Fully Threaded Studs, also known as Continuous Threaded Studs or All Thread Studs, are headless fasteners, threaded continuously along the entire length of the stud. Fully threaded studs are usually fastened with two nuts, and are designed for use in applications that entail high tension.

We manufacture high quality alloy 20 bolts to ASTM/ASME/DIN standards and specifications. Alloy 20, also known as “Carpenter 20” and “20CB-3”, is a nickel-chromium-molybdenum stainless steel alloy designed for sulfuric acid applications. Its corrosion resistance also lends itself to many other uses in the chemical, food, pharmaceutical and plastics industries. One of the main reasons that alloy 20 fasteners are so common is that they resist pitting and chloride ion corrosion, and their copper content protects it from sulfuric acid.

Under alternating oxidizing and reducing conditions the alloy may suffer from selective oxidation.

Alloy 625 is a nickel-chromium alloy known and used for corrosion and oxidation resistance, and its high strength and fabricability.

Inconel 718 Hex Nuts are also used in high temperature applications such as steam generators, gas turbines, rocket engines, spacecraft, pumps, tools and nuclear pressurized water reactors. Inconel 718 hex bolts are nearly twice as strong as Inconel 625 fasteners.

Grade 1.4529 is a high alloy stainless steel of austenitic structure and can be classified as a nickel alloy (by US standards). Delivered in a supersaturated condition, it exhibits resistance to intergranular corrosion, pitting and stress corrosion, salt, seawater, chlorides, sulfuric acid, phosphoric acid, and other highly concentrated liquid and gaseous corrosive chemicals. At the same time, nickel and nitrogen can not only improve the stability, but also reduce the tendency of separation of crystallization thermal process or welding process is better than the nitrogen content of nickel alloy. 926 has some corrosion resistance to chloride ions due to its localized corrosion characteristics and 25% nickel alloy content.