Alloy A193 B7 A194 2H Washers with minimum tensile strength requirement of 125 ksi

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Chromium-molybdenum alloy steel has strong crack resistance under high temperature and high pressure. Chromium molybdenum is also resistant to hydrogen attack and hot sulfide corrosion cracking.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Grade 1 alloy steel plate has very high corrosion resistance, but it is increasingly expensive. Our alloy steel products are known worldwide for their reliability and quality.

ASTM A182 F11 class 1 Flange is the method of connecting two pipes, pumps and valves. This consists of chromium molybdenum based alloy steel grade.

Alloy Steel AISI 4140 bar stock or forging stock to produce B7 headed and non-headed bolts. A193 Grade B7 is the most commonly used Bolt specification coupled with A194 Grade 2H Nuts for Bolting Carbon Steel pipeline. A193 B7 bolting is available in metric sizes from M6 to M180 and imperial sizes from 1/4 to 7 inches, in diameter.

A weld neck flange, also called a tapered hub flange or high-hub flange, is a kind of flange that can relocate stress to the pipes, ensuring a decrease in high-stress concentration at the bottom of the flange.

ASTM A320 L7 washers are specially engineered for LOW temperature performance. These fasteners are commonly used for valves, flanges, fittings, and pressure vessels.

It is almost the same as AISI 4130 chrome-molybdenum alloy steel, but with a slightly higher carbon content. Compared to AISI/ASTM 4130 alloy steel, AISI 4140 steel has a higher carbon content, which provides higher strength and heat treating capability, but also has limited weldability.

It can be used with other a335 gr P22 alloy tube types and fittings. SA 335 gr P22 alloy steel pipe has high heat resistance and low thermal expansion. This property of P22 metal tubing makes it suitable for use in the oil and gas industry, power industry, petrochemical industry and refineries where temperatures often fluctuate at high temperatures.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.44

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

We also provide various alloy steel ASTM A182 F5 flanges, such as ASTM A182 F5 slip-on flanges, alloy steel F5 butt weld flanges, F5 alloy steel socket weld flanges, A182 F5 alloy steel blind flanges, alloy steel F5 Orifice Flange, A182 Alloy Steel F5 Blind Flange, A182 F5 Threaded/Threaded Flange, Alloy Steel F5 Reducing Flange, ASTM A182 F5 Alloy Steel Ring Type Joint Flange (RTJ) etc.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

These supplied alloy steel F2 A182 bars are manufactured synchronously through set industry specifications using high quality raw materials and leading technology. Regarding the domestic and international quality of the raw materials, we also offer these round bars and bars in custom sizes.

ASTM A193 Grade B7 specification covers the requirements for high strength alloy steel bolting materials for high temperature or high pressure service and other special purpose applications. It is a standard specification that defines typical chemical composition, mechanical properties, hardness requirements, preferential heat treatment, product marking, certification, and other requirements for bolted connections used in pressure vessel service, valves, flanges, and fittings. ASTM A193 defines SI (metric) and inch-pound units.

ASTM 182 is used for pressure systems, including fittings, flanges,and similar parts that conform to specified dimensions or dimensional standards such as ASME codes.

ASTM A182 Grade F2 is an alloy steel used for preliminary forming into forged products. The properties cited apply to the annealing conditions. F2 is the ASTM designation for the material. K12122 is the UNS number.

ASTM A335 P11 seamless pipes are used in the production of transmission components in the automotive industry. Tubing is also used in the oil and gas industry because it is stronger, harder and has good properties at high temperatures.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P130

ASTM A193 Grade B7 bolts are made of chrome-molybdenum material with high tensile strength and good elongation properties.

Due to its ease of welding, ASTM A335 Grade P91 Welded Pipe can be welded well into piping systems. Pipes have different tolerance classes and test standards depending on the application requirements, grade, schedule and pressure rating of the pipe material.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.28

Chrome Moly Alloy A182 F11 Flanges is thus manufactured by regal sales corporation as it is the most reputed and well-known firm in the steel industry.

A182 F2 round bar has high strength, formability and hardenability.

WPHY 52 chemical composition includes metals like Manganese, aluminium, phosphorus, sulphur, vanadium, silicon, nickel, titanium, chromium, molybdenum and copper.A few other moved forward ASTM A860 WPHY 52 properties are its expanded solidness, expanded sturdiness, moved forward weldability, great resistance to hydrogen stretch breaking and its exact measurement.

These alloys typically comprise of about 1 % to 5% of the steel’s content and are usually added based on their ability to provide a very specific attribute for their end use.

When connecting these parts, put gasket in the middle of two flanges, then tightening the flange screws, so the two will be connected together tightly.

These well-controlled advantages of Astm a182 alloy steel F9 round bars are evident in automated operations where even modest changes in flow temperature can significantly increase the incidence of scrap.

The most common application for A182 F2 round bars is shafts. It has various alloying elements that enhance its mechanical properties.

The high chromium content gives these forgings fittings very good resistance to moisture erosion, which also contributes to their high temperature strength and resistance to scaling at high temperatures.

Flanges are usually welded or threaded. Flange joints are made by bolting two flanges together with a gasket between them to provide a seal.