Alloy C276 Forged Flange

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Inconel 600 flat washers are also non-magnetic and offer the perfect combination of high strength, hot and cold workability, and resistance to common forms of corrosion. Inconel Alloy 600 ferrules exhibit excellent toughness even at sub-zero temperatures and are suitable for use with most alkaline solutions and sulfides. To avoid stress corrosion cracking, Alloy 600 split washers are manufactured to be fully stress relieved prior to use.

Alloy C-276 prevents the formation of grain boundary precipitates in the weld heat affected zone, making it useful in most welding conditions for chemical processes.

Although there are several variants of Hastelloy nickel alloys, Hastelloy C-276 is by far the most widely used.

Machining of Hastelloy UNS N10276 polished plates is best done in the annealed condition. Since this particular alloy grade is prone to work hardening, only low cutting speeds are required.

HASTELLOY(r) B-2 is a wrought nickel-molybdenum alloy that can be used in the ¡®as welded¡¯ condition.

The material is resistant to chlorides and acids so that the primary uses are in the acid processing, chemical, sea water and marine applications.

Hastelloy B2 pipe bend provides resistance to pure sulfuric acid and a number of non-oxidizing acids. The alloy should not be used in oxidizing media or where oxidizing contaminants are available in reducing media.

The flange is second most used joining method after welding. Flanges are used when joints need dismantling. It provides flexbility for maintenance. Flange connects the pipe with various equiment and valves. Breakup flanges are adde din the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrelated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls ae required in the selection and application of all these elements to attain a joint, which has acceotable leak tightness.

Hastelloy C-276 alloy excellent resistance to a wide variety of chemical process environments, including strong oxidizers such as ferric and cupric chlorides, and hot contaminated media (organic and inorganic).

Bushings are similar to thin tubes most commonly used in machinery with rotating or sliding shafts to increase efficiency and reduce vibration and noise. Bushings can be used for drilling operations in drill stands, hydraulic external gear pumps and motors.

Hastelloy C22 Slip On Flanges (UNS N06022) is used in Chlorination systems, Nuclear fuel reprocessing, Pickling systems, and more.

The corrosion resistance property of the alloy is credited to the addition of both Molybdenum and nickel.

Hastelloy C276 has a low carbon content to minimize grain boundary carbide precipitation during welding to maintain corrosion resistance in the heat affected zone of the welded joint

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

Alloy B-3 also withstands sulfuric, acetic, formic and phosphoric acids, and other non-oxidizing media.

Industry users like the resistance to a wide range of organic acids and the resistance to chloride-induced stress-corrosion cracking.

A nickel alloy of this type also has great resistance to hydrochloric acid at different concentrations and temperatures.

Hastelloy B2 EFW Pipes is highly resistant to all concentrations and temperatures of hydrochloric acid.

Hastelloy C22 Spectacle Blind Flanges is also in a wide variety of hazardous waste management technologies where high corrosion ¨C resistance of critical equipment is required for reliability, safety, and cost effectiveness / reduced maintenance.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

HASTELLOY(r) C276 can be formed by cold working using conventional techniques.

Alloy C-22 should not be used in service temperatures above 1250¡ã F due to the formation of detrimental phases which form above this temperature.

Hastelloy B2 is a nickel-molybdenum alloy especially suitable for handling equipment that reduces chemical environments. Such as applications in chemical processing industries involving sulfuric acid, phosphoric acid, hydrochloric acid and acetic acid.

Alloy B Its popularity has been hindered by its availability. All of these materials are good against reducing acids, but very hard against oxidizing acids. Due to the high molybdenum content, this alloy is relatively expensive than other alloys. At the same time, it has excellent corrosion resistance to medium-concentrated sulfuric acid and various non-oxidizing acids, good resistance to chloride stress corrosion cracking (SCC), and good resistance to various organic acids.

Hastelloy C-4 is a nickel-chromium-molybdenum alloy with outstanding high temperature stability. It has high ductility and corrosion resistance. It’s high temperature resistance up to 1900 ¡ãF (1038 ¡ãC) makes it suitable for most chemical process application in the “as” welded condition.
Like other nickel alloys, it is ductile, easy to form and weld, and possesses exceptional resistance to stress corrosion cracking in chloride-bearing solutions (a form of degradation to
which the austenitic stainless steels are prone). With its high chromium and molybdenum
contents, it is able to withstand both oxidizing and non-oxidizing acids, and is resistant to
pitting and crevice attack in the presence of chlorides and other halides.

Hastelloy C-4 is a nickel-chromium-molybdenum alloy with outstanding high temperature stability. It has high ductility and corrosion resistance. It’s high temperature resistance up to 1900 ¡ãF (1038 ¡ãC) makes it suitable for most chemical process application in the “as” welded condition.
Like other nickel alloys, it is ductile, easy to form and weld, and possesses exceptional resistance to stress corrosion cracking in chloride-bearing solutions (a form of degradation to
which the austenitic stainless steels are prone). With its high chromium and molybdenum
contents, it is able to withstand both oxidizing and non-oxidizing acids, and is resistant to
pitting and crevice attack in the presence of chlorides and other halides.

Hastelloy C276 Flanges are made up of the nickel chromium molybdenum alloy that is called hastelloy. The composition includes 50.99% nickel, 14.5% chromium, 15% molybdenum and carbon, manganese, silicon, sulfur, cobalt, iron and phosphorus in it.

Alloy B2 is a highly resistant material to most organic and inorganic acids. It is a reduction resistant material.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

The Hastelloy C276 round tube is manufactured from a high temperature heat resistant alloy, which contributes to its widespread use in the power industry. Whereas, Hastelloy C276 pipe exhibits outstanding properties such as high wear resistance, corrosion resistance and longer service life due to the raw materials used in its processing.