alloy pipe seamless 13crmo44

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Alloy steel F12 square bars can withstand very high temperatures with minimal product aging even after thousands of operating hours,

These continuous ¨C annealing furnaces in Alloy Steel Grade F12 RTJ Flanges are usually heated by gas ¨C fired radiation tubes in order to separate combustion gases from the inert atmosphere surrounding the strip. Alloy Steel F12 Flanges has applications in many industries such as petrochemical, oil and gas, bulk liquid transportation, pharmaceuticals, chemical, pulp and paper manufacturing, power generation, textiles and others.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

A blind flange is a solid flange as shown below. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used.

The ease and economy with which INCONEL alloy 718
can be fabricated, combined with good tensile, fatigue,
creep, and rupture strength, have resulted in its use in a
wide range of applications.

The ANSI B16.5 Alloy Steel Slip On Flange is a flange type that allows the pipes to slip onto the flange and makes the connection in a precise locations.

Bolts and bolts are used in many applications in almost all industrial applications.

When the carbon content of the a333 gr 6 welded pipe chemistry is lower, the chance of cracking in the welded area is also lower. However, some manufacturers prefer seamless pipes over welded pipes. The reason behind this is that the performance of the a333 gr 6 seamless tube is almost 20% higher than the welded one in high pressure environments.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.57

Stainless steel is a versatile alloy is considered to be amongst the most widely used metals across the world.Stainless Steel A403 WP304 contains higher chromium and low carbon content.

The composition of A335 P91 material contains carbon, manganese, phosphorus, sulfur, silicon, chromium, molybdenum, vanadium, nitrogen, nickel, aluminum, niobium, titanium and zirconium. There are two kinds of seamless pipes and welded pipes. Seamless pipe is drawn from a single raw material billet, while ASTM A335 Gr P91 Welded Pipe is welded from strip or sheet. Welding can be helical or longitudinal from one end to the other to produce the tube. The minimum yield strength of the pipe is 415MPa and the minimum tensile strength is 585MPa.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.60

Seamless pipes are used with slip on flanges to make the process smooth. The Alloy Steel Blind Flanges are used to close a pipe connection.

The material contains carbon, manganese, phosphorus, sulfur, silicon, 8% chromium and molybdenum in a mixture. SA 335 grade P5 alloy steel pipe has similar strength to most austenitic stainless steel grades, with a minimum yield strength of 205MPa and a minimum tensile strength of 415MPa.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P120

This ASTM A182 alloy steel flange has a smaller thickness for easier placement of bolt holes. These ASTM A182 F12 alloy steel pipe flanges are suitable for high temperature and high pressure environments.

The range of pipe diameters of A335 that can be tested by each method should be limited by the respective scope of practice. The different mechanical testing requirements for pipes, i.e. transverse or longitudinal tensile tests, flattening tests, hardness or bending tests, are presented.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.22

They have a minimum yield strength of 105ksi. There are different types of bolts and bolts for different types of applications such as ASTM A193 gr b7 hex bolts.

SA 182 Gr F1 Slip on Flanges also known as SO flanges. This is a flange that slides over the pipe and has an internal design that is slightly larger than the pipe.

ASTM A335 grade P91 tubing contains small amounts of other alloys such as aluminum, niobium, nickel, nitrogen, titanium, vanadium, and zirconium. These pipes are based on the A335 standard, but when forged or drilled, the pipes can also meet the A369 standard. These pipes have a minimum yield strength of 415 MPA and a minimum tensile strength of 585 MPA.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.30

ASTM 182 is used for pressure systems, including fittings, flanges,and similar parts that conform to specified dimensions or dimensional standards such as ASME codes.

ASME SA 335 / ASTM A335 P91 pipe has some great features like fully tested, cost effective, quality certified and more. The ASTM A335 Alloy Steel P91 Pipe offered is manufactured by our experts utilizing the highest quality stainless steel and advanced technology.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.49

Impact strength as well as high surface smoothness are the result of round bar forging of alloy steel DIN 1.7335. Once the materials are forged, they are allowed to cool to the temperature specified by the specification ASTM A 182.

Despite adding these elements, low alloy steel flanges aren’t necessarily difficult to weld. The key to achieve a successful performance of the welding operation is by knowing exactly what type of low-alloy steel you have.

The Alloy Steel Weld Neck Flange has a welded neck onto it that holds larger pipes in place for easy welding and installation.

Chrome molybdenum flanges provide higher levels of chromium and molybdenum. The added chromium helps improve the hardenability and corrosion resistance of the steel, while the added molybdenum helps to enhance its toughness and corrosion resistance.

In order to strengthen chromium alloy flanges, elements such as copper, titanium, vanadium and niobium are added to the alloy.

Our alloy steel blind flanges are mainly caused by environmental factors such as wind exposure, man-made pollution and high temperature, and are more serious near the ocean, which is the main cause of seawater pollution.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

This specification covers forged low alloy flanges for use in pressure systems manufactured to specified dimensions or industry standard dimensional specifications.

ASTM A860 MSS SP 75 WPHY 52 Fittings are generally used at High Pressure requirements.Our wide range of Grade WPHY 52 Pipe Fittings includes: WPHY Gr 52 Bend, Elbow WPHY 52 in 45/90 degree, WPHY Grade 52 Tees, Carbon Steel WPHY 52 U Bend, MSS SP75 WPHY Gr 52 Stubends & ASTM A860 WPHY Grade 52 Pipe Nipple.

ASTM A335 P9 pipe standards and schedules vary based on the needs of the application. A335 P9 chromium pipe composition contains 9% chromium and 1% molybdenum.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.55

ASTM A182 F11 Alloy Steel Flanges are used in manufacturing of flanges and fittings and are used in industries where cold temperature is observed and corrosion resistance doesn¡¯t matter much.