Alloy Steel ASTM A182 F5 F9 F11 F12 F22 Flange ANSI B16.5 Alloy Steel Flange

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Grade B7 is a heat treated chromium molybdenum low alloy steel with a minimum tensile strength requirement of 125 ksi (860 Mpa), a yield strength of 105 ksi (720 Mpa) and a maximum hardness of 35HRC. Boltport produces B7 headed and headless bolts from alloy steel AISI 4140 bar stock or forgings. A193 Grade B7 is the most commonly used bolting size, plus A194 Grade 2H nuts are used for bolting carbon steel pipe. A193 B7 bolts are available in metric sizes from M6 to M180 and imperial sizes from 1/4 to 7 inches in diameter.

The alloy must be cooled for heat treatment prior to AISI AS F11 Hex Bar. All parameters of the heat treatment procedure are set by the specification, including the type of heat treatment, austenitization/solution temperature, and alloy steel F11 A182 bars.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

ASTM A860 WPHY 60 Fittings are wrought carbon steel fittings that are either seamless or welded with high yield strength. The WPHY 60 indicates that the minimum yield strength of the ASTM A860 WPHY 60 Fittings is 60ksi.

For A335, chromium is a key ingredient used to make stainless steel. If the chromium content is above 12%, it can be classified as stainless steel. Even at high temperatures, the antioxidant potential of chromium is irreplaceable. Better hardness, tensile strength and yield strength at standard temperature. Due to the material’s composition, it is ideal for use in power plants, refineries, petrochemical plants and other oilfield services involving high temperature and high pressure transportation.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P108

In addition to good corrosion resistance, the addition of chromium and molybdenum to the alloy enhances its ductility.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Inconel600 is suitable for welding with the same material or other metals by any traditional welding process, such as tungsten electrode inert gas welding, plasma arc welding, manual sub-arc welding, metal inert gas shielded welding, molten arc inert gas shielded welding, and pulsed arc welding. Welding is the preferred solution. When using manual arc welding, it is recommended to use a shielding gas mixed with various components (Ar+He+H2+CO2).
Welding of Incoloy 825 must be carried out in the annealed condition and cleaned with a stainless steel wire brush to remove stains, dust and various markings. When welding the root of the weld, extreme care must be taken (Argon 99.99) to obtain the best quality of the root weld so that the weld does not produce oxides after the root has been welded. Color from the weld heat-affected zone should be removed with a stainless steel brush while the weld area is not cool.

ASTM A182 Alloy Steel Blind Flanges is a solid disk used to block off a pipeline or to create a stop. It has mounting holes around the perimeter and the gasket sealing rings are machined into the mating surface.

ASME SA 335 grade P22 alloy steel pipe can withstand high pressure and high temperature. Therefore, ASTM A335 P22 pipe is used in applications that need to operate at high pressure and high temperature.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.42

ASTM A193 Grade B8M Grade 1 Fasteners are similar to Grade B8 but are made of AISI 316 stainless steel instead of AISI 304 stainless steel. Type 316 stainless steel has better corrosion resistance than type 304 stainless steel due to the addition of molybdenum.

A blind flange is a solid flange as shown below. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used.

A193 B7 threaded rods are also known as hex bolts. It has threads on both ends and it is a relatively long rod.

The Alloy Steel F12 Flanges are also very strong due to the annealing of them. Grade F12 Flanges can be supplied in either normalized or quenched and tempered conditions. Alloy Steel F12 Weld Neck Flanges is appropriate to various applications where its different remarkable characteristics are sought-after but a brushed/polished finish is not necessary.

A182-F11 is an American standard pearlitic structure heat-resistant steel forgings, the execution standard: ASTM-A182/A182M-2017.

ASTM A182 is the Standard Specification for Forged Stainless Steel Pipe Flanges and Stainless Steel Forged Fittings.

ASTM A182 Gr F1 Blind Flange is a solid disc used to block a pipe or create a stop. It is similar to an ordinary flange, with mounting holes around it, and the sealing ring is machined into a mating surface.

We offer ASME SA335 Grade P22 Welded Pipe, ASTM A335 P22 Pipe is manufactured according to ASTM standards. Alloy steel A335 P22 ERW tube, Astm A335 P22 temperature extreme cold formed, made from steel strip drawn through a series of rolls.

The grade mark consists of the grade symbol “2H” and the manufacturer’s identification mark.

The A335 Chromium (or Chromium) is the basic component of stainless steel. Any steel with 12% or more chromium is considered stainless steel. Chromium is almost irreplaceable in terms of resistance to oxidation at high temperatures. Chromium increases tensile, yield and hardness at room temperature.

Production of low alloy steel materials of different specifications. A335 is a specification for seamless ferritic alloy steel pipes. These alloy steel seamless pipes are used for high temperature service. There are also high alloy steel materials. There are different grades in this material specification. There are grades P1, P2 to P91 and P92. The most commonly used grades are p5, p9, p11, p22, p91 and p91.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P136

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

ASTM A182 F12 alloy steel flanges also contain niobium to prevent sensitization and resulting intergranular corrosion.

ASTM A335 seamless steel pipe is commonly referred to as chrome molybdenum pipe with chemical elements molybdenum and chromium. Molybdenum can improve steel properties such as strength, elastic limit, wear resistance, impact resistance and hardenability.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P93

These ASTM A182 Alloy Steel pipe fittings are manufactured from high quality raw materials, so the manufactured products are of high quality. Additionally, these ASTM A182 Alloy Steel pipe fittings are manufactured with the necessary standards, codes and guidelines in mind, resulting in a high quality product.

At elevated temperatures, conventional steels, unlike ASTM A 335 P91 pipes, begin to lose their microstructural form, leading to failure. A burst or crack in the pipe is a visible fault. But since SA 335 P91 chrome-plated welded pipe is well suited to sustain itself at high temperatures, failure rates are extremely low.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

Several ANSI/ ASME standards use materials that are forged or cast to produce Cast AS Blind Flanges.

Unlike the bends, the elbows can reduce the pressure applied on the walls when turning the fluid flow direction.Fittings made from WPHY 52 material are known to have a long work life, durable, tough and hard. The WPHY 52 properties make these fittings a perfect cost saving solution for a variety of industries.

ASTM A194 2h nuts are available in nominal sizes ranging from ?” to 4″. These products are made with heavy duty hex nuts with different proof load stresses for regular nuts and zinc plated nuts. A194 2h coupling nut with 175ksi plain nut and 150ksi zinc plated nut. Fasteners of this grade of material also have high hardness.

Steel pipes are used in structures, transportation, and manufacturing. They are sized according to their outer diameter, with the inner diameter varying based on wall thickness. Some applications need thicker walls than others, depending on the forces the pipe must manage.