alloy steel astm a193 grade b16 bolts and nuts for high temperature service

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Pipe Fittings are usually socket welded or threaded. The high chromium content gives these forgings fittings very good resistance to moisture erosion

Alloy steel pipe is an economical section steel. Widely used in the manufacture of structural and mechanical parts, such as oil drill pipes, automobile drive shafts, bicycle frames and steel scaffolding for construction. Making ring parts with alloy steel pipes can improve material utilization, simplify the manufacturing process, save materials and processing time, such as: filling bearing rings, jack sleeves, etc. At present, steel pipes have been widely used in manufacturing.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.25

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

These industries are rely on MSS SP75 WPHY 52 Welded Pipe Fittings and MSS SP75 WPHY Grade 52 Seamless Pipe Fitting because these fittings can withstand severe corrosion problems in harsh conditions.ASTM A860 WPHY 52 are Created High Yield fittings and are by and large utilized at High-pressure prerequisites.

A335/SA335 materials are used in a wide variety of plants and processes worldwide, including refineries, power plants, petrochemical plants, hydrocrackers, cokers, high temperature and ultra-high temperature lines, reheat lines, distillation, oil field service, and more.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P144

At elevated temperatures, conventional steels, unlike ASTM A 335 P91 pipes, begin to lose their microstructural form, leading to failure. A burst or crack in the pipe is a visible fault. But since SA 335 P91 chrome-plated welded pipe is well suited to sustain itself at high temperatures, failure rates are extremely low.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

This specification covers forged low alloy flanges for use in pressure systems manufactured to specified dimensions or industry standard dimensional specifications.

Please make sure to contact us for more information on the pipe fitting products such as the ASTM A860 MSS SP 75 WPHY 52 Pipe Fittings and their pricing.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Alloy pipe is a higher percentage of tubular alloying elements such as molybdenum (Mo), chromium (Cr), nickel, etc. than standard carbon steel pipe. In fact, ASTM A335 covers “low alloy” steel pipes, that is, having less than 5% total alloying elements. The addition of higher percentages of alloying elements such as nickel and chromium converts the steel into higher alloys such as stainless steel, duplex stainless steel, up to superalloyed materials such as Inconel, Hastelloy, Monel, etc.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P100

There is absolutely no risk of intercrystalline corrosion on cooling or welding in Alloy Steel(AS) F12 Slip-on Flanges due to the low carbon content.Alloy Steel F12 Weld Neck Flanges is appropriate to various applications where its different remarkable characteristics are sought-after but a brushed/polished finish is not necessary.

A blind flange is a solid flange as shown below. The purpose of these is to block off a section of pipe or a nozzle on a vessel that is not used.

These are used in applications where the resistance required is not much and general corrosion resistance is required.

The production of ASME SA182 F9 flanges will be done using alloys with lower carbon content. Reducing the carbon content in these alloys reduces the formation of carbide precipitates. This basically means that alloy steel F9 flanges will no longer be susceptible to intergranular corrosion in the heat affected weld zone.

They have a minimum yield strength of 105ksi. There are different types of bolts and bolts for different types of applications such as ASTM A193 gr b7 hex bolts.

Steel pipes are used in structures, transportation, and manufacturing. They are sized according to their outer diameter, with the inner diameter varying based on wall thickness. Some applications need thicker walls than others, depending on the forces the pipe must manage.

ASME SA182 F5 pipe flange weight depends on wall thickness and nominal bore. The wall thickness of the flange is determined by the pressure rating.

These pipes are supplied with ASTM A182 F11 flanges for the mining, construction and aerospace industries, giving them resistance to sensation, and they also give you maximum strength. They are also made from the highest quality raw materials.

Our 4310 seamless pipes implement strict quality specifications and strictly follow every level of production. So this allows us to take our quality goals to a higher level. Every product is tested to national and global quality standards. In addition, we also provide customers with specific tests according to their application requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.39

Chromium (or chromium) in A335 is an essential element in stainless steel production. Steel products are defined as stainless steels with 12% or more chromium added. Chromium is widely used due to its excellent heat resistance properties and is irreplaceable in terms of resistance to oxidation in high temperature applications.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P96

The precise properties of our A335 tubing meet the most stringent requirements. We meet all requirements for standard and non-standard size alloy steel products. We are a regular supplier of alloy steel products in a variety of styles, standards, models and custom sizes.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.31

A182-F11 is an American standard pearlitic structure heat-resistant steel forgings, the execution standard: ASTM-A182/A182M-2017.

F11 alloy steel pipe flange is the second most common connection method after welding. Use them when joints need to be disassembled. ASTM A182 Gr F11 flanges provide flexibility for maintenance. It connects pipes with various equipment and valves.

A182 F91 Wrought alloy steel tubes, flanges, wrought fittings and valves and other components for high temperature use.

Our Alloy Steel ASTM A182 F5 Weld-neck Flanges are supplied to aid industrial, high pressure services like condensers, boilers, evaporators, heat exchangers, etc. Alloy steel F5 A182 flanges is also available in the form of lap joint flanges, plate flanges, threaded flanges, reducing flanges and many more. These flanges are widely used in power generation industry, gas processing industry, pharmaceutical industry, heat exchangers industry, sea water equipment industry, oil drilling companies and many more.

These well-controlled advantages of Astm a182 alloy steel F9 round bars are evident in automated operations where even modest changes in flow temperature can significantly increase the incidence of scrap.

Chromium-molybdenum alloy steel has strong crack resistance under high temperature and high pressure. Chromium molybdenum is also resistant to hydrogen attack and hot sulfide corrosion cracking.

There are different types and grades of the blind flanges as well. There are other different types of ASME SA 182 AS Pipe Flanges such as the weld neck flanges and socket weld flanges each specified for a particular role

The alloy has great mechanical properties at subzero temperatures.For catering to the needs of our customers better, it is essential that we manufacture Monel Pipe Fittings in different types, with each one serving some specific purpose.