alloy steel pipe tube

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Pipe to ASTM A335 P11 can be cold drawn or hot rolled. Each tube shall be reheated for heat treatment – fully or isothermally annealed, normalized and tempered at a temperature not lower than 1200¡ãF (650¡ãC). Each pipe length shall be hydrostatically tested to ASTM A335 P11, along with dimensional inspection and visual inspection. Longitudinal or transverse tensile tests, flattening tests or bending tests are carried out for each heat.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P129

ASME SA 335 P11 pipe is a pipe made of chrome molybdenum alloy. It is used for high temperature service. It is corrosion resistant, strong and malleable.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.53

High alloy steel and low alloy steel are two types of alloy steel. Low-alloy steel pipes consist of pipes with an alloying percentage of less than 5%. The alloy content of high alloy steels varies from 5% to about 50%. Similar to most alloys, the working pressure capacity of alloy steel seamless pipe is about 20% higher than that of welded pipe.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.64

ASTM A182 F5 flanges are ready for industrial, construction and transportation applications.

Chrome moly alloy flanges connect pipes, valves, pumps and other equipment, forming a piping system.

ASTM A182 Gr F9 flanges are typically designed for applications with high temperature requirements. Alloys used to produce flanges according to this specification include wrought or rolled alloys and several stainless steel grades.

When connecting these parts, put gasket in the middle of two flanges, then tightening the flange screws, so the two will be connected together tightly.

Alloy steel pipes are common in applications involving automobiles, kitchenware, and industrial equipment. Typically, superalloy steel boiler tubes are used in applications with ambient temperatures exceeding 500¡ãC. For example, hollow and thin-walled alloy steel drill pipes must be able to resist pressure differences that manifest between the inside and the outside of these alloy steel seamless pipes.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.45

Weld Neck Flange is expensive because of its long neck and cost of people for contact WN flange with pipeline or fitting but is preferred for high-stress applications. The necks, or hubs, transmits stresses to the pipeline.

ASME SA335 P9 Alloy Steel Seamless Pipe is certified and tested according to Tensile Test, Transverse Tensile Test, Flattening Test, Metal Structure and Etching Test, Photomicrograph, Hardness Test, etc.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.25

A333 P92 steel is American steel grade ASTM A335 P92, which is a martensitic heat-resistant steel. In recent years, it has been widely used in thermal power plants, mainly for main steam pipelines and reheat steam pipelines. The main alloy components are Cr: 9%, Mo: 1%, etc.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.59

This specification covers forged low alloy flanges for use in pressure systems manufactured to specified dimensions or industry standard dimensional specifications.

The precise properties of our A335 tubing meet the most stringent requirements. We meet all requirements for standard and non-standard size alloy steel products. We are a regular supplier of alloy steel products in a variety of styles, standards, models and custom sizes.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.31

The ASTM A333 specification covers carbon steel pipes for low temperature applications. LTCS or Low Temperature Carbon Steel is an alloy covered under this specific specification. A333 carbon steel cryogenic tubing specified by ASTM has moderate tensile properties and good hardness, but low corrosion resistance. The corrosion resistance of the alloy can be improved by using certain surface treatments.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.41

Flanges are usually welded or threaded. Flange joints are made by bolting two flanges together with a gasket between them to provide a seal.

The production of ASME SA182 F9 flanges will be done using alloys with lower carbon content. Reducing the carbon content in these alloys reduces the formation of carbide precipitates. This basically means that alloy steel F9 flanges will no longer be susceptible to intergranular corrosion in the heat affected weld zone.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

B8M Grade 1 fasteners require carbide solution treatment, while Grade 2 fasteners require additional strain hardening operations to increase strength and reduce susceptibility to wear.

Alloy Steel Flanges are made in different steel alloys. The flanges vary in dimensions and types. There are ? inches through 48 inches of nominal diameter sizes of flanges.

The ease and economy with which INCONEL alloy 718
can be fabricated, combined with good tensile, fatigue,
creep, and rupture strength, have resulted in its use in a
wide range of applications.

A182 F2 round bar has high strength, formability and hardenability.

A182 threaded flanges are primarily used for utility services such as air and water. It is similar to a Slip-On flange, but the holes are threaded.

Due to the chemical composition of Molybdenum (Mo) and Chromium (Cr), A335 is often referred to as Chromium Molybdenum Tube. Molybdenum increases the strength of the steel as well as the elastic limit, wear resistance, impact quality and hardenability. Molybdenum increases resistance to softening, inhibits grain growth, and makes chromium steel less susceptible to embrittlement. Molybdenum is the most effective single additive for improving high temperature creep strength. It also enhances the corrosion resistance of the steel and inhibits pitting corrosion. Chromium (or chrome) is the basic component of stainless steel. Any steel with 12% or more chromium is considered stainless steel. Chromium is almost irreplaceable in terms of resistance to oxidation at high temperatures. Chromium increases tensile, yield and hardness at room temperature.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P99

Several ANSI/ ASME standards use materials that are forged or cast to produce Cast AS Blind Flanges.

F5 A182 Pipe Flanges tends to have a fairly high electrical conductivity amongst other wrought alloy steels in the same category. It has a comparatively high base cost and high embodied energy. ASTM A182 is the Standard Specification for Forged Stainless Steel Pipe Flanges and Stainless Steel Forged Fittings.

These ASTM A182 alloy steel F12 flanges are corrosion resistant. ASTM A182 alloy steel F12 flanges also have high dimensional accuracy.

Alloy 20 (Alloy 20) is an iron-based austenitic alloy developed to resist sulfuric acid corrosion. It has excellent resistance to sulfuric acid corrosion; it has strong resistance to phosphoric acid, nitric acid and chloride environments, chloride stress corrosion, pitting corrosion and crack corrosion. Therefore, alloy 20 has the name of anti-corrosion alloy; it has a wide range of applications: such as: chemical, food, medicine, power production and plastics industries will use it. For resistance to pitting corrosion and chloride corrosion, stress corrosion cracking problems, etc., alloy 20 is often used.

ASTM A194 Grade 2H bolts are high strength bolts made from carbon steel.

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

It helps improve fatigue resistance. Many industries, including paper and pulp, chemical reprocessing, water pipelines, nuclear power plants, heat exchangers and others, use ASME sa182 f12 projects in a variety of applications. Our Premium Alloy Steel F12 Flanges are corrosion free, edge perfect, efficient, lightweight, frictionless work, easy to install, highly conductive and of great quality.