ANSI Alloy Steel Flanges ASTM A182 flanges ASME Flanges BS Flanges DIN Flanges

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

HastelloyC-276 (Hastelloy) is a tungsten-nickel-chromium-molybdenum alloy with extremely low silicon-carbon content and is considered to be an all-around corrosion-resistant aluminum alloy. The key moisture-resistant chlorine, various air-oxidizing fluorides, isopropyl titanate solutions, hydrochloric acid and air-oxidizing salts, have good corrosion resistance in ultra-low temperature and standing temperature sulfuric acid. Therefore, in the past 30 years, it has been widely used in extremely corrosive natural environments such as chemical plants, petrochemicals, flue gas desulfurization, pulp and paper industry, and environmental protection.

Corrosion resistance

The aluminum alloy has the following characteristics: 1. It has good corrosion resistance to most corrosive substances under the two conditions of air oxidation and repair. ¢ÚIt has good resistance to pitting corrosion, void corrosion and intergranular corrosion. The higher content of Mo and Cr makes the aluminum alloy resistant to corrosion by chloride ion content, and the W element further improves the corrosion resistance. At the same time, Hastelloy C-276 aluminum alloy is one of the only types of raw materials that are resistant to wet chlorine, hypochlorite and chlorine dioxide saturated solutions. Ester solution has obvious corrosion resistance. It is one of the very few raw materials that can be used as a hot sulfuric acid saturated solution.

These fittings are available in different types such as elbows,couplings,tees crosses,plugs,pipe nipples etc.

Chromium molybdenum pipes under ASTM and ASME specifications A/SA 335 P1, P2, P11, P12, P15, P22, P91, P92, P122 are used in the power industry, while ASTM/ASME A/SA 335 P5, P9 are used in the petrochemical industry, It has strong crack resistance at high temperature and high pressure, can be used for hydrogen sulfide corrosion service, hydrogen attack and embrittlement cracking
Resistant to hot sulfide corrosion cracking.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.57

ASTM/ASME A387/SA387 Alloy Steel Gr. 5 CL 1/2 is a chrome molybdenum alloy steel plate primarily used in welded boilers and pressure vessels designed for high temperature service. The Cr content was 5.00%, and the Mo content was 0.5%.

We are committed to supplying high quality A335 alloy tubes to our esteemed customers at the most reasonable price. Following the principles of Total Quality Assurance is our risk. In pursuit of total quality, we have developed a quality specification and quality assurance work plan.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.38

A182-F11 is an American standard pearlitic structure heat-resistant steel forgings, the execution standard: ASTM-A182/A182M-2017.

A194 2H Heavy Duty Hex bolts are designed for high strength, high temperature or high pressure applications and are usually available in a plain finish.

A low alloy steel flanges series mostly consists of approximately 0.5% to 9% of Chromium. And the content of Molybdenum in the alloy steel flanges ranges anywhere between 0.5% to 1% .

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

One of the top stocks of ASTM A182 alloy steel F5 flanges for a variety of industrial applications. With a talented team of professionals, we are committed to supplying the highest quality ASTM A182 Alloy Steel F5 Flanges, widely used by customers in suitable applications.

ASTM A182 alloy steel F12 flanges are corrosion resistant. ASTM A182 alloy steel F12 flanges also have high dimensional accuracy. These ASTM A182 alloy steel F12 flanges also have a rust-proof finish. They are used in numerous industrial applications. These applications include the paper and pulp industry, the oil and gas industry, and more.

This ASTM A182 alloy steel flange has a smaller thickness for easier placement of bolt holes. These ASTM A182 F12 alloy steel pipe flanges are suitable for high temperature and high pressure environments.

It is almost the same as AISI 4130 chrome-molybdenum alloy steel, but with a slightly higher carbon content. Compared to AISI/ASTM 4130 alloy steel, AISI 4140 steel has a higher carbon content, which provides higher strength and heat treating capability, but also has limited weldability.

Other than carbon, these contain in them substantial quantities of nickel, manganese, chromium, silicon, tungsten, vanadium, molybdenum.

The Chromoly based F12 material specification are ideal for applications, where the piping systems are to transport or carrying corrosive fluids or gases at high-temperatures. Alloy Steel F12 Flanges they are used in various applications. Applications include chemical equipment, pharmaceuticals, gas processing plants, power generation tools, petrochemical industry, pulp and paper industry, on shore and offshore marine equipment, oil rigs, oil refineries, under water equipment, water desalination plants, condensers, heat exchangers and others.

A335 grade P9 alloy steel round pipe is your best choice. It surrounds pipes made of alloy steel. It’s graded very well, making it unique. It has excellent properties such as toughness, durability, weldability, and low electrical conductivity.

Too many good properties found in the same product just because of better sheet production. These are high tensile strength, good dimensional accuracy, surface finish, flexibility and durability, withstand heavy loads, strong construction and corrosion resistance. Resistance to corrosion, stress corrosion cracking, crevice corrosion cracking, oxidation/pitting corrosion makes it suitable for a variety of applications.

We supply these ANSI B16.5 Plate Flanges to the irrigation industry.

This specification covers forged low alloy flanges for use in pressure systems manufactured to specified dimensions or industry standard dimensional specifications.

Cold drawn and cold rolled tube types are available. There are seamless tubes, welded tubes, ERW tubes and fabricated tubes. Seamless pipe is made from a single piece of material, whereas ASTM A333 Grade 6 Welded Pipe Specification requires it to be welded from strip or sheet of the same material grade.

Chromium-molybdenum alloy steel has strong crack resistance under high temperature and high pressure. Chromium molybdenum is also resistant to hydrogen attack and hot sulfide corrosion cracking.

ASTM A193 Grade B7 is a standard material specification for chromium-molybdenum alloy steel fasteners for use in high tensile, high temperature and special purpose applications.

It is available in materials of ASTM A 182, and ASTM A 105. The flanges are available in various grades like ASME B16 47 ¡®A¡¯ Series, and ¡®B¡¯ Series to suit the needs of the clients and the industry.

We are a manufacturer, trader, stocker, supplier and exporter of B7-2H Fasteners.

L7 threaded studs and short head bolts are readily available in the market.

A335 has improved wear resistance at higher temperatures. It has good formability and machinability without deformation and deformation. It has good thermal stability in pressurized environments.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.35

Besides these elements the addition of trace amounts of both Manganese and silicon, other set of common alloying elements, provides the alloy steel threaded flanges with excellent deoxidizing capabilities.

Alloy steel pipes and tubing are the best choice for stress corrosion cracking (SSC). These also apply to environments where the problem is pitting and crevice corrosion. These tubes and tubes are available within machining allowances and tolerances.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.34

A335 p9 pipes are made of ferritic alloy steel for high temperature applications. The sa335 p9 material chemically contains metals such as molybdenum and chromium added to the alloy. By adding metals such as molybdenum and chromium, the tensile strength of the alloy is increased. The yield strength of the a335 p9 welded pipe is 205 Mpa, while its tensile strength is 415 Mpa. The elongation of the pipe is about 30%.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P151