ANSI Alloy Steel Flanges ASTM A182 flanges offers Rust proof finish and Smooth transition from flange thickness to pipe

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Flanges are usually welded or threaded. Flange joints are made by bolting two flanges together with a gasket between them to provide a seal.

Chromium Molybdenum Alloy Steel or Chromium Molybdenum, CrMo is an alloy steel used for high temperature and high pressure service. Chromium molybdenum is used in power generation and petrochemical industries for its tensile strength, corrosion resistance and high temperature strength. Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

Its greatest advantage is that it can be assembled without welding, which explains its use in low-pressure service at ordinary atmospheric temperatures and in highly explosive areas where welding creates a hazard.

ASTM A193 Grade B7 specification covers the requirements for high strength alloy steel bolting materials for high temperature or high pressure service and other special purpose applications. It is a standard specification that defines typical chemical composition, mechanical properties, hardness requirements, preferential heat treatment, product marking, certification, and other requirements for bolted connections used in pressure vessel service, valves, flanges, and fittings. ASTM A193 defines SI (metric) and inch-pound units.

Alloy steel is divided into two categories: high-alloy steel and low-alloy steel. Low alloy steel forged fittings, on the other hand, contain about 0.05 ¨C 0.25% carbon and up to 2.0% manganese.

ASTM A194 Grade 2H Nut is a carbon based steel heavy duty nut. It is a commonly used high strength nut.

Schedules vary based on nominal bore diameter in relation to wall thickness. Schedules range from sch20 to XXS. Pipe lengths up to 13500 mm. There are seamless pipes and fabricated pipes in this specification. ASTM A335 P5 pipe can be round, hydraulic, rectangular, square or hexagonal. The length of the pipe can also be cut to length size according to customer requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P148

INCONEL? alloy 718 (UNS N07718/W.Nr. 2.4668) is a high-strength, corrosion-resistant nickel chromium material used at -423¡ã to 1300¡ãF. Inconel alloys are resistant to oxidation and have the ability to maintain its structural integrity in high temperature atmospheres.

A335 P22 is a seamless tube made of ferritic alloy stainless steel. Chemically, the alloy of SA335 P22 material contains trace amounts of carbon, manganese, sulfur, silicon and phosphorus. The main additives in the alloy are molybdenum and chromium, which give stainless steel excellent mechanical properties. Tensile strength, corrosion resistance, hardness and other properties are enhanced and improved. Molybdenum reduces the brittleness caused by the addition of chromium.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P132

Many applications in various industries. Pharmaceutical, petrochemical, chemical, etc., are industries where ASTM A182 F9 Weld Neck Flange is widely used. SA 182 Gr F9 Steel Flanges are known to provide an easy access for cleaning, inspection or modification due to their ease in assembling and dis- assembling.

A335 has improved wear resistance at higher temperatures. It has good formability and machinability without deformation and deformation. It has good thermal stability in pressurized environments.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.35

ASTM A182 Gr F1 Blind Flange is a solid disc used to block a pipe or create a stop. It is similar to an ordinary flange, with mounting holes around it, and the sealing ring is machined into a mating surface.

ASME SA 335 / ASTM A335 P91 pipe has some great features like fully tested, cost effective, quality certified and more. The ASTM A335 Alloy Steel P91 Pipe offered is manufactured by our experts utilizing the highest quality stainless steel and advanced technology.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.49

Alloy Steel AISI 4140 bar stock or forging stock to produce B7 headed and non-headed bolts. A193 Grade B7 is the most commonly used Bolt specification coupled with A194 Grade 2H Nuts for Bolting Carbon Steel pipeline. A193 B7 bolting is available in metric sizes from M6 to M180 and imperial sizes from 1/4 to 7 inches, in diameter.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

There is absolutely no risk of intercrystalline corrosion on cooling or welding in Alloy Steel(AS) F12 Slip-on Flanges due to the low carbon content.Alloy Steel F12 Weld Neck Flanges is appropriate to various applications where its different remarkable characteristics are sought-after but a brushed/polished finish is not necessary.

The A335 p12 material composition includes carbon up to 0.05 ¨C 0.15, manganese up to 0.30 ¨C 0.61, sulfur and phosphorus up to 0.025, silicon up to 0.5, chromium 0.80-1.25 and molybdenum up to 0.44-0.65. This steel shall meet the specified chemical composition, tensile properties and hardness requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.66

We supply these ANSI B16.5 Plate Flanges to the irrigation industry.

The ANSI B16.5 Alloy Steel Slip On Flange is a flange type that allows the pipes to slip onto the flange and makes the connection in a precise locations.

ASTM A193 Grade B7 is the standard material specification for chromium-molybdenum alloy steel fasteners for high-strength, high-temperature, and special-purpose applications. Grade B7 is a heat treated chromium molybdenum alloy steel with a minimum tensile requirement of 100 ksi, a yield strength of 75 ksi and a maximum hardness of 35 HRC. The ASTM A193 specification covers requirements for chemical composition, mechanical properties, hardness, heat treatment, and recommended nut washers for Class B7 fasteners. ASTM A193 Grade B7 is the broadest specification for fasteners, commonly found in bolts or pipes, pressure vessels, valves, flanges and fittings.

A335 P22 Chromium Pipe contains chromium in its composition to provide high corrosion resistance. There are other elements in the material composition of P22 steel pipe. Molybdenum is a common addition in all A335 grades. Manganese, phosphorus, silicon and carbon are added according to different grades.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.43

The flanges also come in B16.5, B16.47 and other standards and dimensions. The Alloy Steel Flange Material can vary according to the chemical composition.

ASTM A335 gr P91 seamless pipe has the advantage of being dimensionally accurate, which in turn is suitable for applications that require high precision. The petrochemical industry, oil and gas industry, power plants and refineries often involve high temperatures and pressures.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.25

HASTELLOY C-276 alloy is available in the form of plates, sheets, strips, billets, bars,
wires, pipes, tubes, and covered electrodes.

We feel proud to introduce ourselves as the well-known manufacturers, exporters and suppliers of Alloy Steel F21 Flanges.

Monel 400? has low corrosion rate in flowing seawater, therefore it is widely used in marine applications.We make use of the best manufacturing techniques for their production so that the final product being served to the customers is the best of best.

Alloy 20 (Alloy 20) is an iron-based austenitic alloy developed to resist sulfuric acid corrosion. It has excellent resistance to sulfuric acid corrosion; it has strong resistance to phosphoric acid, nitric acid and chloride environments, chloride stress corrosion, pitting corrosion and crack corrosion. Therefore, alloy 20 has the name of anti-corrosion alloy; it has a wide range of applications: such as: chemical, food, medicine, power production and plastics industries will use it. For resistance to pitting corrosion and chloride corrosion, stress corrosion cracking problems, etc., alloy 20 is often used.

ASTM A182 Alloy Steel F22 Fittings are available in a variety of shapes, sizes and dimensions according to the needs or requirements of the application or to customer supplied specifications.

Chromium molybdenum is used in power generation and petrochemical industries for its tensile strength, corrosion resistance and high temperature strength.