ASME B16.5 Alloy Steel Flange for oil and gas

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

The flange connection type usually comes with double units, with a gasket and some bolts & nuts to connect each other. (Firstly pipes are welded on the flanges, then valves and other equipment could be installed on flanges.)

ASTM A182 Stainless Steel Flanges are manufactured per ASME B16.5 150#, 300#, 600#, 900#, 1500#, 2500#.

A182 threaded flanges are primarily used for utility services such as air and water. It is similar to a Slip-On flange, but the holes are threaded.

Each tube of the A335 shall be hydrostatically tested. In addition, each tube shall be inspected using non-destructive testing methods in accordance with prescribed practices.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.21

Alloy 20 (Alloy 20) is an iron-based austenitic alloy developed to resist sulfuric acid corrosion. It has excellent resistance to sulfuric acid corrosion; it has strong resistance to phosphoric acid, nitric acid and chloride environments, chloride stress corrosion, pitting corrosion and crack corrosion. Therefore, alloy 20 has the name of anti-corrosion alloy; it has a wide range of applications: such as: chemical, food, medicine, power production and plastics industries will use it. For resistance to pitting corrosion and chloride corrosion, stress corrosion cracking problems, etc., alloy 20 is often used.

A194 2H nut is a common high strength nut used with many different bolt grades, including A193 Grade B7, A325, A490, etc.

The ASTM A333 standard covers seamless walled and welded carbon and alloy steel pipes for cryogenic use. ASTM A333 Alloy Pipe shall be manufactured in a seamless or welded process with no filler metal added during the welding operation.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.61

These Alloy F5 Flange are used for transferring liquid and other fluids to several industries. We are manufactured by a team of nimble-fingered professionals using high quality raw material, modern tools and advance technology.

B7 and B7M shall be heat treated by quenching in a liquid medium and tempering. For B7M fasteners, the final heat treatment, which may be the tempering operation if conducted at 1150 ¡ãF [620 ¡ãC] minimum, shall be done after all machining and forming operations, including thread rolling and any type of cutting.

ASTM A335 P5 pipe can be fully annealed or isothermally annealed, normalized and tempered as heat treatments to increase hardness. This grade is available in welded and seamless pipe, A335 P5 welded pipe is available in different wall thicknesses and diameters.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P121

Our alloy steel pipes are available in different sizes, grades, gauges and thicknesses according to customer’s custom requirements. We also supply these alloy steel LSAW pipes to our valuable customers at fairly reasonable prices.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19

We offer a wide range of ASTM A335 P9 alloy steel seamless pipes using high quality raw materials. These alloy steel P9 ERW tubes are forged between 2250¡ãF/1750¡ãF (1230¡ãC/955¡ãC) for 30 minutes per inch of billet or ingot section thickness. These are A335 P9 pipes manufactured to international quality standards. These alloy steel P9 seamless pipes are also available in different sizes, grades, thicknesses and specifications according to customer requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P141

We are a professional manufacturer and exporter of ASTM B366 WP20CB Pipe Fittings N08020 elbow, Alloy 20 Elbow Tee reducer Caps

The ASTM A333 specification covers carbon steel pipes for low temperature applications. LTCS or Low Temperature Carbon Steel is an alloy covered under this specific specification. A333 carbon steel cryogenic tubing specified by ASTM has moderate tensile properties and good hardness, but low corrosion resistance. The corrosion resistance of the alloy can be improved by using certain surface treatments.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.41

SA335 material is available in different pressure grades, SA335 P11 material is special in that it can be used in most high pressure and high temperature services. In this range there are seamless pipes and welded pipes, which are used for different requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.54

The addition of elements such as silicon and manganese through heat treatment provides alloyed steel with improved properties and additional benefits, such as increased corrosion resistance or increased reliability. Alloy steels are also found in applications where their response to magnetism is important, such as in transformers and electric motors.

A335 P9 steel pipe material also contains manganese, silicon, carbon and phosphorus in its composition. The addition of these materials makes the material stronger with higher yield and tensile strengths. Due to the high chromium content, the redox effect is high.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.37

Alloy steel is divided into two categories: high-alloy steel and low-alloy steel. Low alloy steel flanges, on the other hand, contain about 0.05 ¨C 0.25% carbon and up to 2.0% manganese.

The material can be heat treated to anneal and normalize in air, or quench and temper in polymer or oil. Alloy 4130 has a lower carbon content of 0.28% – 0.33% and slightly higher amounts of other elements. And the material is easy to process. 4140 low alloy steel has a range of 2. 375″ to 12.750″ OD with wall thicknesses ranging from 0.375″ to 1.5″. Alloy 4145 has a slightly higher carbon content than 4140 and 4130 types of pipes.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P139

ASTM A320 L7 washers are specially engineered for LOW temperature performance. These fasteners are commonly used for valves, flanges, fittings, and pressure vessels.

Alloy pipe is a higher percentage of tubular alloying elements such as molybdenum (Mo), chromium (Cr), nickel, etc. than standard carbon steel pipe. In fact, ASTM A335 covers “low alloy” steel pipes, that is, having less than 5% total alloying elements. The addition of higher percentages of alloying elements such as nickel and chromium converts the steel into higher alloys such as stainless steel, duplex stainless steel, up to superalloyed materials such as Inconel, Hastelloy, Monel, etc.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P100

These are said to be specifications for alloy flanges for high pressure and service. The 3% carbon content of these flanges provides a lot of room for improved weldability, which also increases their overall strength.

Impact strength as well as high surface smoothness are the result of round bar forging of alloy steel DIN 1.7335. Once the materials are forged, they are allowed to cool to the temperature specified by the specification ASTM A 182.

ASTM A335 is the standard specification for seamless ferritic alloy steel pipe for high temperature service. Covers server levels: P1, P2, P5, P5b, P5c, P9, P11, P12, P15, P21, P22, P23, P91, P92, P122, of which P5, P9, P11, P22, P91, P92 are used in practice the most extensive. This specification covers nominal and minimum wall chrome-molybdenum (also known as Cr-Mo or Cr-Moly) alloy steel pipes for high temperature applications. Pipe ordered to this specification shall be suitable for bending, vanstoning and similar forming operations, and fusion welding. ASTM A335 P11, P22, P91 and P92 are commonly used in power plants and the chemical and petrochemical industries, while P9 and P5 are mainly used in oil refineries.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P106

Our alloy steel ASTM A182 F5 butt weld flanges can be used in auxiliary industrial high pressure services such as condensers, boilers, evaporators, heat exchangers and more.

Chrome molybdenum grades P11, P22, P91 and P92 are used in the power industry. Chromium molybdenum grades P5 and P9 are used in petrochemical refining processes. Chrome molybdenum forged fittings and flanges are available in grades F5, F9, F11, F22, F91, F92. Chrome-molybdenum alloy butt welded pipe fittings are available in WP5, WP9, WP11, WP22, WP91, WP92 grades. F11 and F22 materials comply with NACE-MRO 175.

The composition of the chrome-molybdenum alloy steel pipe in A335 makes it ideal for power plants, refineries, petrochemical plants and oilfield services that transport fluids and gases at extremely high temperatures and pressures.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P119

Chromium-molybdenum alloy flanges connect pipes, valves, pumps and other equipment to form a piping system. They are ideal for applications that convey corrosive or high temperature fluids or gases.

Monel 400? can be used in temperatures up to 1000 oF. Monel K-500 is basically a better version of 400 and has higher strength and hardness.

All chrome molybdenum steel sheets are sedated and heat treated in accordance with ASTM A387, which also specifies minimum and maximum levels of the following elements in steel: Chemicals of Carbon, Manganese, Phosphorus, Sulfur, Silicon, Chromium, Molybdenum, Nickel, Vanadium requirements, columbium, boron, nitrogen, aluminum, titanium and zirconium. A387 boards must undergo product, chemical and tensile testing (documented in the MTC or material test certificate) – must meet specific requirements for tensile strength, yield strength and elongation.