asme b16.5 nickel alloy flange SW flange Monel K500 WERKSTOFF NR. 2.4361 flange

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

The corrosion resistance of Monel K500 Weld Neck Flanges is substantially equivalent to that of alloy 400 Weld Neck Flanges except that, when in the age ¨C hardened condition, it has a greater tendency toward stress ¨C corrosion cracking in some environments.

The chemical composition of Monel K500 ASTM is approximately 65% nickel, 30% copper and 3% aluminum. Monel 500 exhibits excellent corrosion resistance with added high strength corrosion fatigue and erosion resistance. Monel K500 fasteners are non-magnetic at high and low temperatures. The material has the same corrosion resistance as Monel Class 400.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

Monel K500 Flat Washers feature aluminum and titanium elements for the excellent corrosion resistance of Alloy 400; improved strength, hardness, erosion resistance and oxidation fatigue resistance. We manufacture all types of Monel K500 machined washers in virtually all shapes and sizes.

Monel400 alloy is a versatile material that can be used in many industrial applications

ALLOY K500,Monel K500 is a Ni-Cu alloy with age-hardening properties imparted by alloying additions of aluminium and titanium. Its basic composition is similar to that of ALLOY400 but the alloying additions make it age hardenable under
controlled conditions of temperature and time

Alloy 400 is virtually immune to chloride ion stress corrosion cracking in typical environments.

Alloy 400 is a solid solution of gold that can only be hardened by cold work.

Alloy 400 is a solid solution of gold that can only be hardened by cold work.

Monelk500, also known as UNS N05500, has the same corrosion resistance as monel400, but has higher mechanical strength and hardness. It has good corrosion resistance and long-term organizational stability.

Monel K500 pipe bend and elbow are usually used in propeller, pump shafts, pumps, valves used in the manufacture of perchlorethylene, and chlorinated plastics.

Monel K500 alloy has excellent corrosion resistance, and has higher strength and hardness than Monel 400. This is due to the addition of elements such as Al and Ti to the alloy, and after a certain heat treatment, there are dispersed intermetallic compounds on the substrate.

Alloy 400 is a solid solution alloy that can only be hardened by cold working.

At room temperature settings, Monel 400 exhibits slight magnetic behavior, thus, the use of WNR 2.4360 Reducing Flange could also be extended to applications that require magnetic characteristics to a certain degree.

The Alloy 400 Slip-on Flange is often seen in the marine industry as the alloy exhibits have good resistance to not only seawater but also to high velocity brackish water.

Monel 400 is a popular high performance nickel copper alloy commonly used in critical and high performance applications. Monel 400? has high strength, excellent resistance to acid and alkaline environments, and good ductility and thermal conductivity. This alloy maintains its properties and performance in temperatures ranging from subzero to 1,000¡ãF (538¡ãC). Monel 400 can only be hardened by cold work.

As a corrosion resistant alloy, Monel 400 can withstand high temperature steam environments and fast flowing brackish/seawater, while maintaining excellent resistance to stress corrosion cracking in most fresh waters.

In applications that involve being used at subzero temperature, the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance

Spring washers are locking washers that are used when there is a need to prevent a fastener from loosening as a result of vibration. They are also often called split lock or split ring washers.

If hardened Monel 400 is the goal, cold working with a soft tooling material is the only option. By cold working, mechanical stress is used instead of heat to change the shape of the metal.

Stronger than 400, alloy K500 washer even retains this strength in corrosive. conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

We manufacture Monel K500 flanges from nickel and copper alloys. The material has excellent resistance to aggressive materials and solutions such as oxidizing salts, acids, nitrates and other oxidizing agents.

The seamless pipes can easily slip onto the flange and reach the precise connection location. The ASTM B564 Monel 400 Lap Joint Flanges and other flanges can also come as threaded, forged, screwed or plate flange types. We could do solution treatment and ageing treatment for Monel K-500 forging flanges as per the clients. Monel is based on nickel (65-70%) and copper (20-29%) and also contains iron and manganese (5%) and other compounds.

The Monel Alloy 400 Threaded Flanges are fitted with pipes with threads. The male threads on the pipe ends fit with the female threads on the threaded flanges. The ASME SB564 Alloy 400 Socket Weld Flanges are usually welded onto the pipes.

Monel 400 Flanges are made up of a nickel copper super alloy that is corrosion resistant and strong. The material could be welded easily and formed well.

The chemical composition of Monel K500 Nippo Flanges provides great resistance to a lot of corrosive environments, such as pitting, crevice corrosion, inter ¨C granular corrosion, and stress ¨C corrosion cracking. Monel K500 Spacer Flanges has useful resistance to boiling sulfuric acid up to 40 % concentration, to 60 % concentration at 176 Degree F and in all concentrations to 150 Degree F.

Monel 400 flanges are a nickel-copper alloy (approximately 67% Ni ¨C 23% Cu) resistant to seawater and steam at high temperatures, as well as salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold work. This nickel alloy has good corrosion resistance, good weldability and high strength.

Una aleacion de niquel-cobre con alta resistencia y excelente resistencia a la corrosion en una variedad de ambientes acidos y alcalinos, especialmente para condiciones reductoras. Tambien tiene buena ductilidad y conductividad termica.

Monel K500 bolts and nuts are used in a variety of industries due to their high temperature resistance, high corrosion resistance and durability. It is a nickel-copper alloy with a composition of 63% nickel and 27% copper, among other elements.

Monel 400 has excellent corrosion resistance in hot concentrated alkaline solution.