Astm A182 317 1.4449 Rtj Lwn Lap Joint Forged Wn Ss316 Class 300 Ansi B16.5 Slip On Ss Blind Flange

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

304 Piping Spools are made of 304 Stainless Steel, a common and popular material in many industrial applications that require resistance to corrosion and oxidation. These S30400 Piping Spools are prefabricated using specialized machinery and processes, which ensure that they are highly accurate and reliable.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

Inconel 718 is a nickel-chromium-based alloy that is commonly used in high-temperature applications such as aerospace and gas turbines. One of the most important factors in the production of ASTM B670 Inconel 718 Sheet is the plate rolling process. There are two main types of Inconel 718 plates available on the market: hot rolled and cold rolled plates.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

ASME B36.19M is the standard specification for stainless steel pipes, which specifies the dimensions, tolerance, and manufacturing requirements for both welded and seamless pipes.

MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance.

Our alloy steel ASTM A182 F5 butt weld flanges can be used in auxiliary industrial high pressure services such as condensers, boilers, evaporators, heat exchangers and more.

Stainless Steel 316L fasteners are made of low carbon austenitic stainless steel. The material is carbon, manganese, silicon, phosphorus, sulfur, 18% chromium, 2% molybdenum, 10% nickel and nitrogen. There are different types of fasteners such as SS UNS S31600 square bolts, hex bolts, screws, nuts and washers.

The alloy is capable of remaining stable and maintaining its austenitic structure. Incoloy 800 is primarily used in applications with temperatures up to 1100¡ã F, where alloys 800H and 800HT are normally used in temperatures above 1100¡ã F where resistance to creep and rupture is required.

Duplex stainless steels have a mixed microstructure of austenite and ferrite, the aim being to produce a 50/50 mix, although, in commercial alloys, the mix may be 40/60 respectively.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Uns S30400 304/304L SS WNRF Flanges
Featuring 304 stainless steel for very good corrosion resistance, this GRAINGER APPROVED weld neck flange can be attached to a system via a circumferential weld at the neck. The welded area can be easily examined by radiography. Matched pipe and flange bore reduces turbulence and erosion inside the pipeline. Flange is excellent for use in your critical applications and is ideal for use with air, water, oil, natural gas, and steam.

All Duplex 2205 Seamless Pipe produced according to the ASTM A789 must be furnished in a heat treated condition.

Stainless Steel 304 SO flanges
Stainless steel forged flanges?are used as a connection component for pipes, valves, pumps and other equipment to form a pipework system.?To make the connectionflanges?are usually welded onto pipes or screwed onto a threaded pipe end and then joined with bolts.

Stainless Steel Flanges are designed with care using current techniques under the visionary guidance of accomplished professionals at manufacturing unit. Offered range is stringently tested on various parameters of quality for ensuring flawlessness and defect free. These products are widely used in various industries and widely appreciated by clients for owning unmatchable characteristics. Offered range supplied in quality assured packaging material.

ASME SA 335 P91 Alloy Steel Pipe also has some other great features like low maintenance, efficient work, high demands, etc. We offer a range of ASTM A335 P91 alloy steel pipes for a wide range of applications in various industries.

UNS S32760 (F55, 1.4501) is a high alloy super duplex stainless steel mainly used in a variety of strongly corrosive environments. S32760 has strong strength and corrosion resistance and is mainly used in chemical processing, petrochemical and subsea equipment.

When compared to other types of pipes, the pricing of SS 316 pipes is competitive. Check the quality of the pipes before purchasing them while comparing the 316 stainless steel pipe pricing list.

We are manufacturer & exporters of A105 Flanges, ASTM A350 Carbon Steel Flanges, A694 Carbon Steel Flanges, Alloy Steel Pipe Fittings, ASTM A182 Alloy Steel Flanges, ASTM A182 F5, ASTM A182 F9, ASTM A182 F11, ASTM A182 F12, ASTM A182 F22, ASTM A182 F91, ASTM A105 Flange, ASTM A350 Flanges, ASTM A694 Flanges

Grade 316 stainless steel fasteners are designed for applications in extreme environmental conditions. Therefore, these industries require the 300-grade stainless steel series to provide enhanced protection and higher corrosion resistance. SS 316 Bolts and Nuts are constructed of Ni-Cr-Mo alloy austenitic stainless steel for good strength and excellent corrosion resistance.

SS 316/316L/316Ti round bars/rods are made from chemical compositions such as carbon, nickel, copper, chromium, titanium, iron and manganese. These rods and rods are designed with physical and mechanical properties such as density, yield strength, tensile strength, elongation, thermal conductivity, electrical conductivity, modulus of expansion, and electrical expansion.

Monel 400? sheet is available in thicknesses ranging from .018 to .140″.Butt-weld and forged fittings are available or can be manufactured with short lead times.

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

The alloy also exhibits resistance to physical deterioration, e.g. – surface pitting and cracking.

Our Alloy Steel A234 WP9 Pipe Elbow are available in a number of pipe end connections, like threaded, bevelled, square, grooved, bent, barbed and seamless and in a variety of wall thickness.The salts in Alloy Steel WP9 Pipe Reducer may create when hydrochloric acid interacts with iron and copper.

Flange connection has good strength and sealing, simple structure and low cost. It can be repeatedly disassembled.

ASTM A182 F22 Forging raw material used for the manufacturing process is well-tested and inspected by inspection agencies and quality experts.

Thermocouple sheaths. Ethylene dichloride (EDC) cracking tubes.

304l pipe has good oxidation resistance in intermittent duty up to 870¡ãC and continuous duty up to 925¡ãC. However, continuous use at 425-860¡ãC is not recommended. In this case, 304L is recommended because of its resistance to carbide precipitation. Where high strength is required at temperatures above 500¡ãC and up to 800¡ãC, Grade 304H is recommended. This material will remain resistant to water corrosion.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Inconel 625 elbow has also found its way into the aircraft industry, particularly for exhaust equipment, fuel lines, heat exchanger casings, and rocket components.

The A420 Grade WPL6 fitting is used in pipelines in the paper and pulp industries, condensers, sea water, marine engineering, waste water management and pollution control systems.

Due to its thin chemical composition, RA 253 MA is very economical compared to most heat resistant alloys. Stainless steel 253 MA fasteners have equivalent grades such as UNS S30815, standard SS 253 MA and its WERKSTOFF NR. is 1.4835. The mechanical properties in the specified limit minimum are its 2″ elongation of 40%, its ultimate tensile strength of 87,000 psi, its area reduction of 50%, and its offset yield strength of 45,000 psi.

These Incoloy 800HT Bolt Elbow are made from high quality raw materials resulting in high quality Incoloy 800HT Bolt Elbow. They also have built-in compliance with applicable standards and laws. Additionally, the necessary standards, regulations and guidelines are followed in the manufacture of these Incoloy 800HT Bolted Elbow, resulting in a high quality product. These Incoloy 800HT Bolt Elbow are also well made.

The addition of elements such as silicon and manganese through heat treatment provides alloyed steel with improved properties and additional benefits, such as increased corrosion resistance or increased reliability. Alloy steels are also found in applications where their response to magnetism is important, such as in transformers and electric motors.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

Tempering: The quenched workpiece is heated to an appropriate temperature below the critical point AC1 for a certain period of time, and then cooled by a method that meets the requirements to obtain the required structure and properties.