ASTM A182 Duplex Stainless Steel Flanges provides both high strength and excellent corrosion resistance

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

The service temperature of 2205 duplex stainless steel should be limited to below 600¡ãF. Prolonged exposure to high temperatures can make 2205 stainless steel brittle.

There are different pressure ratings for the flanges based on the system of measurement. Under the ANSI standard, the pressure classes range from class 150 through class 2500.

Super Duplex UNS S32760 Round Rod has many properties and properties due to the elements present in the chemical composition. Due to these characteristics and properties, these super duplex UNS S32760 round bars are used in a large number of industrial applications.

The steel has excellent resistance to chloride stress corrosion cracking, high thermal conductivity, and a low coefficient of thermal expansion.

Super Duplex 2507 cannot be strengthened by heat treating. Annealing is performed at 1920¡ãF – 2060¡ãF (1049¡ãC – 1127¡ãC), followed by rapid cooling.

Duplex steel flange also offers Good weldability and workability, High energy absorption and Low thermal expansion.

Super Duplex Steel Stud Bolt is available in lengths ranging from 2mm to 200mm and has high strength values as well. Super Duplex S32750 is the most common duplex ferritic, austenitic stainless steel grade used for producing stud bolts.

The S31803 fastener series demonstrates the properties of ferritic and austenitic stainless steels. These fasteners exhibit excellent resistance to crevice corrosion, stress corrosion cracking and pitting corrosion in harsh environments. In addition, these are excellent in resistance to chloride and sulfide stress corrosion environments.

Super Duplex 2507 Equal tees are the most common fittings.

Due to the alloy’s strong resistance to chemical compositions including acids, bases and neutral solutions, duplex steel uns s31803 nuts would be an ideal addition to these industries.

Alloy 2205 UNS S32305/S31803 is a 22% chromium, 3% molybdenum, 5-6% nickel, nitrogen alloyed Duplex Stainless Steel Pipe with high general, localized, and stress corrosion resistance properties in addition to high strength and excellent impact toughness.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The chemistry of this steel ensures better performance with higher mechanical properties in comparison to austenitic stainless steel pipes.

It accounts for around 80% of overall duplex stainless steel production.

Duplex 2507 is usually used in Desalination Equipment, Chemical process pressure vessels, piping and heat exchangers and Marine Applications.

Super Duplex Stainless Steel 1.4410 Nuts?is a super duplex stainless steel with 25 percent chromium, 4 percent molybdenum, and 7 percent nickel. High molybdenum, chromium and nitrogen content in?Super Duplex 2507 Hex Nuts?help the material withstand pitting and crevice corrosion.?

2205 flange has good general corrosion resistance, high resistance to chloride stress corrosion cracking, as well as pitting and crevice corrosion.

Duplex steel UNS S31803, UNS S32205 round rods and wires are widely used in chemical, oil and gas, fertilizer and other application industries.

Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Material: Duplex Steel ASTM A789 S31803,S32205,S32750, S32760
ASTM A790 S31803,S32205,S32750, S32760

The combination of the ferritic phase and austenitic phase provides both high strength and excellent corrosion resistance.

S31803 has been supplemented by S32205 (F60) which dual conforms to S31803 but has a higher minimum N, MO, NI and Cr which guarantees a better corrosion resistance.

Duplex 2205 stainless steel (both ferritic and austenitic) is used extensively in applications that require good corrosion resistance and strength. This grade offers higher resistance to corrosion

Duplex stainless steels have a microstructure which is 50% ferritic and 50% austenitic. This composition gives them a better strength than either ferritic or austenitic steels. Further details about this topic are given below (see ASTM A790 pipes).

Duplex UNS S32750 coils have very low corrosion rates under very high corrosive conditions.

Super Duplex UNS S32760 is one of the most common super duplex grades on the market. UNS S32760 is a duplex stainless steel designed for use in corrosive chlorine-containing environments, with the addition of W and Cu compared to UNS S32750.

Some steels also contain the alloy elements such as Mo, Cu, Nb, Ti and N, etc. Compared with ferritic stainless, duplex stainless steel has higher plasticity, ductility and better intergranular corrosion resistance and weldability.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The composition of UNS S32750 super duplex steel strip contains chromium, nickel and molybdenum.

Both ASME B16.5 and ASME B16.47 have endorsed pipe flanges made from a series of duplex stainless steel grades.

DIN 933 technically ranges from M1. 6 to M52, whereas ISO 4017 ranges from M1. 6 to M64. Secondly, that’s it really, the DIN 933 and ISO 4017 standards are the exact same with the exception of M10, M12, M14 and M22.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

In the annealed condition, S31803 contains approximately 40-50% ferrite. S31803 is often referred to as the workhorse grade and is the most widely used grade in duplex stainless steel pipes. The use of S31803 stainless steel pipe should be limited to temperatures below 600¡ãF.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.64